Home › BRAKE › BRAKE CONTROL › ANTI-LOCK BRAKE SYSTEM (for Hatchback)

DTC    C1403    Rear Speed Sensor RH Malfunction

DTC    C1404    Rear Speed Sensor LH Malfunction

for Preparation Click here


DESCRIPTION

Refer to DTCs C1401 and C1402 .

DTC Code
DTC Detection Condition
Trouble Area
C1403
C1404
When any of the following is detected:
  1. At a vehicle speed of 10 km/h (6 mph) or more, the output speed signal from one of the speed sensors is equal to or less than 14 % of that of one of other 3 sensors for 15 seconds or more.
  2. At a vehicle speed of 10 km/h (6 mph) or more, the output from one of the speed sensors is 0 km/h (0 mph) for 1 second or more.
  3. At a vehicle speed of 10 km/h (6 mph) or more, the outputs from 2 of the speed sensors are 0 km/h (0 mph) for 15 seconds or more.
  1. Rear speed sensor RH/LH
  2. Speed sensor rotor
  3. Sensor installation
  4. Brake actuator assembly (Skid control ECU)
C1273
C1274
Detected only during Test Mode.
  1. Rear speed sensor RH/LH
  2. Sensor installation
  3. Speed sensor rotor

HINT:
  1. DTCs C1273 and C1274 are output only in the Test Mode.
  2. DTCs C1273 and C1274 can be deleted when the speed sensor sends a vehicle speed signal or the Test Mode ends.
  3. DTCs C1403 and C1273 are for the rear speed sensor RH.
  4. DTCs C1404 and C1274 are for the rear speed sensor LH.


INSPECTION PROCEDURE

NOTICE:
Do not disassemble the rear speed sensor from the rear axle hub and bearing assembly.

1.CHECK REAR SPEED SENSOR INSTALLATION


    C170210E01
  1. Turn the ignition switch off.

  1. Check the speed sensor installation.

    OK:
    There is no clearance between the sensor and rear axle carrier.

    HINT:
    Because the rear axle hub and bearing assembly cannot be disassembled, if the rear speed sensor needs replacement, replace the rear axle hub and bearing assembly.



NG
REPLACE REAR AXLE HUB AND BEARING ASSEMBLY (REAR SPEED SENSOR) (Click here)
OK


2.INSPECT REAR SPEED SENSOR


    C170209E01
  1. Disconnect the rear speed sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH 
    Tester Connection
    Condition
    Specified Condition
    1 (RR-) - Body ground
    Always
    10 kΩ or higher
    2 (RR+) - Body ground
    Always
    10 kΩ or higher
    for LH 
    Tester Connection
    Condition
    Specified Condition
    1 (RL-) - Body ground
    Always
    10 kΩ or higher
    2 (RL+) - Body ground
    Always
    10 kΩ or higher

    NOTICE:
    Check the speed sensor signal after replacement (Click here).

HINT:
Because the rear axle hub and bearing assembly cannot be disassembled, if the rear speed sensor needs replacement, replace the rear axle hub and bearing assembly.



NG
REPLACE REAR AXLE HUB AND BEARING ASSEMBLY (REAR SPEED SENSOR) (Click here)
OK


3.RECONFIRM DTC
  1. Clear the DTC (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.

  1. Check if the same DTC is recorded (Click here).
    Result 
    Result
    Proceed to
    DTC not output
    A
    DTC output
    B

    HINT:
    If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A

END