Home › BRAKE › BRAKE CONTROL › ANTI-LOCK BRAKE SYSTEM (for Hatchback)

DTC    C1407    Open or Short in Rear Speed Sensor RH Circuit

DTC    C1408    Open or Short in Rear Speed Sensor LH Circuit

for Preparation Click here


DESCRIPTION

Refer to DTCs C1401 and C1402 .

DTC Code
DTC Detection Condition
Trouble Area
C1407
C1408
When any of the following is detected:
  1. Open in speed sensor signal circuit continues for 0.5 seconds or more.
  2. With the IG1 terminal voltage 9.5 V or more, the sensor power supply voltage decreases for 0.5 seconds or more.
  1. Rear speed sensor RH/LH
  2. Speed sensor circuit
  3. Brake actuator assembly (Skid control ECU)
C1273
C1274
Detected only during Test Mode.
  1. Rear speed sensor RH/LH
  2. Sensor installation
  3. Speed sensor rotor

HINT:
  1. DTCs C1273 and C1274 are output only in the Test Mode.
  2. DTCs C1273 and C1274 can be deleted when the speed sensor sends a vehicle speed signal or the Test Mode ends.
  3. DTCs C1407 and C1273 are for the rear speed sensor RH.
  4. DTCs C1408 and C1274 are for the rear speed sensor LH.


WIRING DIAGRAM


C149728E21


INSPECTION PROCEDURE

NOTICE:
Disassembly of the rear speed sensor from the rear axle hub and bearing assembly is prohibited.

1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
  1. Using an intelligent tester, check for any momentary interruption in the wire harness and connector corresponding to a DTC (Click here).

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    RR Speed Open
    RR speed sensor open detection / Error or Normal
    Error: Momentary interruption
    Normal: Normal
    -
    RL Speed Open
    RL speed sensor open detection / Error or Normal
    Error: Momentary interruption
    Normal: Normal
    -

    OK:
    There are no momentary interruptions.

    HINT:
    Perform the above inspection before removing the sensor and connector.



NG
Go to step 3
OK


2.RECONFIRM DTC
  1. Clear the DTC (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.

  1. Check if the same DTC is recorded (Click here).
    Result 
    Result
    Proceed to
    DTC not output
    A
    DTC output
    B



B
Go to step 9
A

CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) (Click here)  

3.CHECK IF SKID CONTROL ECU AND REAR SPEED SENSOR CONNECTOR ARE SECURELY CONNECTED
  1. Check if the skid control ECU and the rear speed sensor connectors are securely connected.


NEXT


4.RECONFIRM DTC
  1. Clear the DTC (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.

  1. Check if the same DTC is recorded (Click here).
    Result 
    Result
    Proceed to
    DTC output
    A
    DTC not output
    B



B
END
A


5.INSPECT REAR SPEED SENSOR
  1. Make sure that there is no looseness at the locking part and the connecting part of the connectors.



    C170209E01
  1. Disconnect the rear speed sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH:
    Tester Connection
    Condition
    Specified Condition
    1 (RR-) - Body ground
    Always
    10 kΩ or higher
    2 (RR+) - Body ground
    Always
    10 kΩ or higher
    for LH:
    Tester Connection
    Condition
    Specified Condition
    1 (RL-) - Body ground
    Always
    10 kΩ or higher
    2 (RL+) - Body ground
    Always
    10 kΩ or higher

    NOTICE:
    Check the speed sensor signal after replacement (Click here).

    HINT:
    Because the rear axle hub and bearing assembly cannot be disassembled, if the rear speed sensor needs replacement, replace the rear axle hub and bearing assembly.



NG
REPLACE REAR AXLE HUB AND BEARING ASSEMBLY (REAR SPEED SENSOR) (Click here)
OK


6.CHECK HARNESS AND CONNECTOR (SPEED SENSOR WIRE)


    C129355E08
  1. Disconnect the speed sensor wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH:
    Tester Connection
    Condition
    Specified Condition
    Z1-1 - ZJ1-1
    Always
    10 kΩ or higher
    Z1-1 - ZJ1-2
    Always
    Below 1 Ω
    Z1-1 - Body ground
    Always
    10 kΩ or higher
    Z1-2 - ZJ1-1
    Always
    Below 1 Ω
    Z1-2 - ZJ1-2
    Always
    10 kΩ or higher
    Z1-2 - Body ground
    Always
    10 kΩ or higher
    for LH:
    Tester Connection
    Condition
    Specified Condition
    a1-1 - aJ1-1
    Always
    10 kΩ or higher
    a1-1 - aJ1-2
    Always
    Below 1 Ω
    a1-1 - Body ground
    Always
    10 kΩ or higher
    a1-2 - aJ1-1
    Always
    Below 1 Ω
    a1-2 - aJ1-2
    Always
    10 kΩ or higher
    a1-2 - Body ground
    Always
    10 kΩ or higher

    NOTICE:
    Check the speed sensor signal after replacement (Click here).



NG
REPLACE SPEED SENSOR WIRE
OK


7.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - REAR SPEED SENSOR)


    C168929E06
  1. Reconnect the speed sensor wire.

  1. Disconnect the skid control ECU connector.

  1. Inspect both the connector case and the terminal for deformation and corrosion.

    OK:
    No deformation or corrosion.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH:
    Tester Connection
    Condition
    Specified Condition
    A15-17 (RR+) - Z1-2 (RR+)
    Always
    Below 1 Ω
    A15-17 (RR+) - Body ground
    Always
    10 kΩ or higher
    A15-16 (RR-) - Z1-1 (RR-)
    Always
    Below 1 Ω
    A15-16 (RR-) - Body ground
    Always
    10 kΩ or higher
    for LH:
    Tester Connection
    Condition
    Specified Condition
    A15-5 (RL+) - a1-2 (RL+)
    Always
    Below 1 Ω
    A15-5 (RL+) - Body ground
    Always
    10 kΩ or higher
    A15-4 (RL-) - a1-1 (RL-)
    Always
    Below 1 Ω
    A15-4 (RL-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.INSPECT SKID CONTROL ECU (SENSOR INPUT)


    C156480E22
  1. Reconnect the skid control ECU connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for RH:
    Tester Connection
    Switch Condition
    Specified Condition
    Z1-2 (RR+) - Body ground
    Ignition switch ON
    8 to 14 V
    for LH:
    Tester Connection
    Switch Condition
    Specified Condition
    a1-2 (RL+) - Body ground
    Ignition switch ON
    8 to 14 V



NG
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
OK


9.REPLACE REAR AXLE HUB AND BEARING ASSEMBLY
  1. Turn the ignition switch off.

  1. Replace the rear speed sensor and rear axle hub and bearing assembly (Click here).

    HINT:
    The rear speed sensor rotor is incorporated into the rear axle hub and bearing assembly.
    If the rear speed sensor rotor needs to be replaced, replace it together with the rear axle hub and bearing assembly with rear speed sensor.

    NOTICE:
    Check the speed sensor signal after replacement (Click here).


NEXT


10.RECONFIRM DTC
  1. Clear the DTC (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.

  1. Check if the same DTC is recorded (Click here).
    Result 
    Result
    Proceed to
    DTC not output
    A
    DTC output
    B

    HINT:
    If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A

END