Home › Drivetrain · U340E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM

DTC    P2714    Pressure Control Solenoid "D" Performance (Shift Solenoid Valve SLT)

for Preparation Click here


DESCRIPTION

Shift solenoid valve SLT controls the transmission line pressure for smooth transmission operation based on signals from the throttle position sensor and vehicle speed sensor. The ECM adjusts the current to shift solenoid valve SLT to control the hydraulic line pressure coming from the primary regulator valve. Appropriate line pressure assures smooth shifting with varying engine outputs.

C233512E01


DTC No.
DTC Detection Condition
Trouble Area
P2714
ECM detects malfunction on SLT (ON side) according to difference in revolutions of turbine (input) and output shaft (2 trip detection logic).
  1. Shift solenoid valve SLT remains open or closed
  2. Valve body is blocked
  3. Torque converter assembly
  4. Automatic transaxle (clutch, brake or gear etc.)
  5. Shift solenoid valve SLT

MONITOR DESCRIPTION

In any forward position, when the difference between the revolutions of the turbine and output shaft exceeds the specified value (varies with output speed) determined by the ECM, the ECM illuminates the MIL and stores the DTC. When shift solenoid valve SLT remains on, the oil pressure goes down and the clutch engagement force decreases.

INSPECTION PROCEDURE


ACTIVE TEST

HINT:
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the intelligent tester to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the intelligent tester on.

  6. Enter the following menus: Powertrain / Engine and ECT / Active Test.

  7. In accordance with the display on the tester, perform the Active Test.

    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Activate the Solenoid (SLT)*
    [Test Details]
    Operate shift solenoid SLT and raise line pressure.

    HINT:
    OFF: Line pressure up (when active test of Solenoid (SLT) is performed, ECM turns off SLT solenoid)
    ON: No action (normal operation)

    ON/OFF
    [Vehicle Condition]
    1. Vehicle Stopped
    2. Shift lever in P or N
    3. Vehicle speed sensor normal
    4. Accelerator pedal is released
    *: Activate the Solenoid (SLT) in the Active Test is performed to check the line pressure changes by connecting SST to the automatic transaxle, which is used in the Hydraulic Test (Click here) as well.

    HINT:
    The pressure values in Active Test and Hydraulic Test are different from each other.

1.CHECK OTHER DTCS OUTPUT (IN ADDITION TO DTC P2714)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs using the tester.
    Result 
    Result
    Proceed to
    Only P2714 is output
    A
    P2714 and other DTCs are output
    B

    HINT:
    If any other DTCs besides P2714 are output, perform troubleshooting for those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.INSPECT SHIFT SOLENOID VALVE SLT
C204845E06
  1. Remove shift solenoid valve SLT.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    5.0 to 5.6 Ω

  1. Connect the positive (+) lead with a 21 W bulb to terminal 2 and the negative (-) lead to terminal 1 of the solenoid valve connector, then check the movement of the valve.

    OK:
    The solenoid makes operating sounds.

    Text in Illustration 
    *a
    Component without harness connected
    (Shift Solenoid Valve SLT)



NG
REPLACE SHIFT SOLENOID VALVE SLT (Click here)
OK


3.INSPECT TRANSMISSION VALVE BODY ASSEMBLY
  1. Check the transmission valve body assembly (Click here).

    OK:
    There are no foreign objects on any valves and they operate smoothly.



NG
REPLACE TRANSMISSION VALVE BODY ASSEMBLY (Click here)
OK


4.INSPECT TORQUE CONVERTER ASSEMBLY
  1. Check the torque converter assembly (Click here).

    OK:
    The torque converter operates normally.



NG
REPLACE TORQUE CONVERTER ASSEMBLY (Click here)
OK

REPLACE AUTOMATIC TRANSAXLE ASSEMBLY (Click here)