DTC P0300 Random / Multiple Cylinder Misfire Detected |
DTC P0301 Cylinder 1 Misfire Detected |
DTC P0302 Cylinder 2 Misfire Detected |
DTC P0303 Cylinder 3 Misfire Detected |
DTC P0304 Cylinder 4 Misfire Detected |

| DTC No. | DTC Detection Condition | Trouble Area |
| P0300 | When one of following conditions is detected (2 trip detection logic):
|
|
| P0301 P0302 P0303 P0304 | When one of following conditions is detected (2 trip detection logic):
|
| Required Sensors/Components (Main) | Camshaft position sensor and Crankshaft position sensor |
| Required Sensors/Components (Related) | Engine coolant temperature and intake air temperature sensors and Mass air flow meter |
| Frequency of Operation | Continuous |
| Intake air temperature | -10°C or higher |
| Either of following conditions (a) or (b) met | - |
| (a)Engine coolant temperature at engine start | Higher than -7°C (19°F) |
| (b) Engine coolant temperature | Higher than 20°C (68°F) |
| Duration | Crankshaft 1000 revolution x 4 |
| Duration | Crankshaft 200 revolution x 3 |
| Engine Speed (rpm) | Duration |
| Idling | 8.0 minutes or more |
| 1000 | 4.5 minutes or more |
| 2000 | 2.5 minutes or more |
| 3000 | 1.5 minutes or more |
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO MISFIRE DTCS) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read DTCs.
| Result | Proceed to |
| DTC P0300, P0301, P0302, P0303 and/or P0304 are output | A |
| DTC P0300, P0301, P0302, P0303 and/or P0304 and other DTCs are output | B |
|
| ||||
| A | |
| 2.CHECK PCV HOSE (HOSE CONNECTIONS) |
Check the PCV hose connections (Click here).
|
| ||||
| OK | |
| 3.READ VALUE USING INTELLIGENT TESTER (MISFIRE RPM AND MISFIRE LOAD) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Misfire RPM and Misfire Load.
Read and note the Misfire RPM and Misfire Load values.
| NEXT | |
| 4.READ VALUE USING INTELLIGENT TESTER (CYLINDER #1 MISFIRE COUNT, #2, #3 AND #4) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Cylinder #1 Misfire Count, Cylinder #2 Misfire Count, Cylinder #3 Misfire Count and Cylinder #4 Misfire Count.
Start the engine and allow the engine to idle.
Read each value for Cylinder #1 (to #4) Misfire Count displayed on the tester. If no misfire counts occur in any cylinders, perform the following procedures:
Move the shift lever to first gear.
Check the Cylinder #1 (to #4) Misfire Count.
If misfire counts are still not displayed, perform steps "A" and "B", and then check the misfire counts again. Procedure A: Drive the vehicle while satisfying the Misfire RPM and Misfire Load values noted in the "Read Value Using intelligent tester (Misfire RPM and Misfire Load)" procedure above. Procedure B: Check the Cylinder #1 (to #4) Misfire Count.
| Result | Proceed to |
| Most misfires occur in only 1 or 2 cylinders | A |
| 3 cylinders or more have equal misfire counts | B |
|
| ||||
| A | |
| 5.INSPECT SPARK PLUG |
Inspect the spark plug of the misfiring cylinder .
|
| ||||
| OK | |
| 6.CHECK FOR SPARKS (SPARK TEST) |
Perform a spark test .
| NEXT | |
| 7.CHECK CYLINDER COMPRESSION PRESSURE OF MISFIRING CYLINDER |
Measure the cylinder compression pressure of the misfiring cylinder .
|
| ||||
| OK | |
| 8.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL INJECTOR ASSEMBLY) |
![]() |
Disconnect the fuel injector assembly connectors.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| B5-1 - Body ground | Ignition switch ON | 11 to 14 V |
| B7-1 - Body ground | Ignition switch ON | 11 to 14 V |
| B9-1 - Body ground | Ignition switch ON | 11 to 14 V |
| B11-1 - Body ground | Ignition switch ON | 11 to 14 V |
| *a | Front view of wire harness connector (to Fuel Injector Assembly) |
|
| ||||
| OK | |
| 9.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR ASSEMBLY - ECM) |
Disconnect the fuel injector assembly connectors.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| B5-2 - B84-108 (#10) | Always | Below 1 Ω |
| B7-2 - B84-107 (#20) | Always | Below 1 Ω |
| B9-2 - B84-106 (#30) | Always | Below 1 Ω |
| B11-2 - B84-105 (#40) | Always | Below 1 Ω |
| B5-2 or B84-108 (#10) - Body ground | Always | 10 Ω or higher |
| B7-2 or B84-107 (#20) - Body ground | Always | 10 Ω or higher |
| B9-2 or B84-106 (#30) - Body ground | Always | 10 Ω or higher |
| B11-2 or B84-105 (#40) - Body ground | Always | 10 Ω or higher |
|
| ||||
| OK | |
| 10.CHECK FUEL INJECTOR ASSEMBLY OF MISFIRING CYLINDER |
Check the fuel injector assembly injection (whether fuel volume is high or low, and whether injection pattern is poor) (Click here).
|
| ||||
| OK | |
| 11.CHECK INTAKE SYSTEM |
Check the intake system for vacuum leaks (Click here).
|
| ||||
| OK | |
| 12.CHECK FUEL PRESSURE |
Check the fuel pressure .
|
| ||||
| OK | |
| 13.READ VALUE USING INTELLIGENT TESTER (COOLANT TEMP) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.
Read the Data List twice, when the engine is both cold and warmed up.
| Tester Display | Condition | Specified Condition |
| Coolant Temp | Cold engine | Same as ambient air temperature |
| Warm engine | Between 80 and 100°C (176 and 212°F) |
|
| ||||
| OK | |
| 14.READ VALUE USING INTELLIGENT TESTER (MAF) |
Connect the intelligent tester to the DLC3.
Start the engine.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / MAF and Coolant Temp.
Allows the engine to idle until Coolant Temp reaches 75°C (167°F) or higher.
Read MAF with the engine speed 3000 rpm.
| Tester Display | Condition | Specified Condition |
| MAF | Shift lever position: Neutral A/C: Off Engine Speed: 3000 rpm | Between 4.0 gm/sec and 8.0 gm/sec |
|
| ||||
| OK | |
| 15.CHECK VALVE TIMING |
![]() |
Remove the cylinder head cover.
Turn the crankshaft pulley, and align its groove with the timing mark "0" on the timing chain cover.
Check that the timing marks on the camshaft timing sprocket and camshaft timing gear are facing upward as shown in the illustration. If not, turn the crankshaft 1 revolution (360°), then align the marks as above.
| *a | Timing Mark |
|
| ||||
|
| ||||
| 16.CHECK INTAKE SYSTEM |
Check the intake system for vacuum leaks (Click here).
|
| ||||
| OK | |
| 17.CHECK FUEL PRESSURE |
Check the fuel pressure .
|
| ||||
| OK | |
| 18.READ VALUE USING INTELLIGENT TESTER (COOLANT TEMP) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.
Read the Data List twice, when the engine is both cold and warmed up.
| Tester Display | Condition | Specified Condition |
| Coolant Temp | Cold engine | Same as ambient air temperature |
| Warm engine | Between 80 and 100°C (176 and 212°F) |
|
| ||||
| OK | |
| 19.READ VALUE USING INTELLIGENT TESTER (MAF) |
Connect the intelligent tester to the DLC3.
Start the engine.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / MAF and Coolant Temp.
Allows the engine to idle until Coolant Temp reaches 75°C (167°F) or higher.
Read MAF with the engine speed 3000 rpm.
| Tester Display | Condition | Specified Condition |
| MAF | Shift lever position: Neutral A/C: Off Engine Speed: 3000 rpm | Between 4.0 gm/sec and 8.0 gm/sec |
|
| ||||
| OK | |
| 20.INSPECT SPARK PLUG |
Inspect the spark plug of the misfiring cylinder .
|
| ||||
| OK | |
| 21.CHECK FOR SPARKS (SPARK TEST) |
Perform a spark test .
| NEXT | |
| 22.CHECK CYLINDER COMPRESSION PRESSURE OF MISFIRING CYLINDER |
Measure the cylinder compression pressure of the misfiring cylinder .
|
| ||||
| OK | |
| 23.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL INJECTOR ASSEMBLY) |
![]() |
Disconnect the fuel injector assembly connectors.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| B5-1 - Body ground | Ignition switch ON | 11 to 14 V |
| B7-1 - Body ground | Ignition switch ON | 11 to 14 V |
| B9-1 - Body ground | Ignition switch ON | 11 to 14 V |
| B11-1 - Body ground | Ignition switch ON | 11 to 14 V |
| *a | Front view of wire harness connector (to Fuel Injector Assembly) |
|
| ||||
| OK | |
| 24.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR ASSEMBLY - ECM) |
Disconnect the fuel injector assembly connectors.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| B5-2 - B84-108 (#10) | Always | Below 1 Ω |
| B7-2 - B84-107 (#20) | Always | Below 1 Ω |
| B9-2 - B84-106 (#30) | Always | Below 1 Ω |
| B11-2 - B84-105 (#40) | Always | Below 1 Ω |
| B5-2 or B84-108 (#10) - Body ground | Always | 10 Ω or higher |
| B7-2 or B84-107 (#20) - Body ground | Always | 10 Ω or higher |
| B9-2 or B84-106 (#30) - Body ground | Always | 10 Ω or higher |
| B11-2 or B84-105 (#40) - Body ground | Always | 10 Ω or higher |
|
| ||||
| OK | |
| 25.CHECK FUEL INJECTOR ASSEMBLY OF MISFIRING CYLINDER |
Check the fuel injector assembly injection (whether fuel volume is high or low, and whether injection pattern is poor) (Click here).
|
| ||||
| OK | |
| 26.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER CONNECTOR CONNECTION) |
Check the connection and terminal contact pressure of connectors and wire harnesses between the mass air flow meter and ECM (Click here).
| NEXT | |
| 27.CHECK WHETHER DTC OUTPUT RECURS (DTC P0300, P0301, P0302, P0303 AND/OR P0304) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
| DTC P0300, P0301, P0302, P0303 and/or P0304 are output | A |
| DTC is not output | B |
|
| ||||
| A | |
| 28.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM) |
Disconnect the mass air flow meter connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| B72-3 (VG) - B84-118 (VG) | Always | Below 1 Ω |
| B72-2 (E2G) - B84-116 (E2G) | Always | Below 1 Ω |
| B72-3 (VG) or B84-118 (VG) - Body ground | Always | 10 Ω or higher |
|
| ||||
| OK | |
| 29.REPLACE MASS AIR FLOW METER |
Replace the mass air flow meter (Click here).
| NEXT | |
| 30.CHECK WHETHER DTC OUTPUT RECURS (DTC P0300, P0301, P0302, P0303 AND/OR P0304) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
| DTC P0300, P0301, P0302, P0303 and/or P0304 are output | A |
| DTC is not output | B |
|
| ||||
| A | ||
| ||
| 31.CHECK FUEL LINE |
Check the fuel lines for leaks or blockage.
|
| ||||
| OK | ||
| ||