Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM (for Separate Type Yaw Rate Sensor)

DTC    C1210    Zero Point Calibration of Yaw Rate Sensor Undone

DTC    C1336    Zero Point Calibration of Acceleration Sensor Undone

for Preparation Click here


DESCRIPTION

The skid control ECU (brake actuator assembly) receives signals from the yaw rate and deceleration sensor (yaw rate sensor) via the CAN communication system.
The yaw rate and deceleration sensor (yaw rate sensor) has a built in deceleration sensor and detects the vehicle's condition using 2 circuits (GL1, GL2). If there is trouble in the bus lines between the yaw rate and deceleration sensor (yaw rate sensor) and the CAN communication system, the DTCs U0123 (Lost Communication with Yaw Rate Sensor Module) and U0124 (Lost Communication with Lateral Acceleration Sensor Module) are output.
The DTCs are also output when the calibration has not been completed.

DTC No.
DTC Detection Condition
Trouble Area
C1210
Zero point calibration of yaw rate sensor undone.
  1. Yaw rate and deceleration sensor (Yaw rate sensor)
  2. Skid control ECU (Brake actuator assembly)
C1336
Zero point calibration of acceleration sensor undone.
  1. Yaw rate and deceleration sensor (Yaw rate sensor)
  2. Skid control ECU (Brake actuator assembly)

INSPECTION PROCEDURE

NOTICE:
When replacing the brake actuator assembly, perform zero point calibration (Click here).

HINT:
When DTC U0123, U0124 and/or U0126 is output together with DTC C1210 and/or C1336, inspect and repair the trouble areas indicated by DTC U0123, U0124 and/or U0126 first (Click here).

1.PERFORM ZERO POINT CALIBRATION OF YAW RATE AND DECELERATION SENSOR
  1. Perform zero point calibration of the yaw rate and deceleration sensor (Click here).


NEXT


2.PERFORM TEST MODE (SIGNAL CHECK)
  1. Turn the ignition switch off.

  1. Perform the sensor check in the Test Mode procedure (Click here).

    OK:
    All Test Mode DTCs are cleared.

    HINT:
    If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).

Result 
Result
Proceed to
NG
A
OK
B


B
END
A


3.CHECK YAW RATE AND DECELERATION SENSOR (YAW RATE SENSOR)
  1. Turn the ignition switch off.

  1. Check that the yaw rate and deceleration sensor (yaw rate sensor) has been installed properly (Click here).

    OK:
    The sensor should be tightened to the specified torque.
    The sensor is not installed in a tilted position.



NG
INSTALL YAW RATE AND DECELERATION SENSOR (YAW RATE SENSOR) CORRECTLY (Click here)
OK


4.READ VALUE USING INTELLIGENT TESTER (YAW RATE AND DECELERATION SENSOR)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

  1. According to the display on the intelligent tester, read the Data List.

    ABS/VSC/TRC (Skid Control ECU) 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Deceleration Sensor
    Acceleration sensor/
    min.: -18.525 m/s2,
    max.: 18.387 m/s2
    -
    During deceleration/acceleration: Changes continuously
    Deceleration Sensor2
    Acceleration sensor 2/
    min.: -18.525 m/s2,
    max.: 18.387 m/s2
    -
    During deceleration/acceleration: Changes continuously
    Yaw Rate Sensor
    Yaw rate sensor/
    min.: -128°/s,
    max.: 127°/s
    Vehicle stationary: 0°/s
    Right turn: -128 to 0°/s
    Left turn: 0 to 127°/s
    -

  1. Check the yaw rate and deceleration sensor (yaw rate sensor) output value displayed on the intelligent tester.

    OK:
    The yaw rate and deceleration sensor (yaw rate sensor) output value is normal.

    NOTICE:
    Check the yaw rate and deceleration sensor (yaw rate sensor) signal after replacement (Click here).

HINT:
If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).



NG
REPLACE YAW RATE AND DECELERATION SENSOR (YAW RATE SENSOR) (Click here)
OK

REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)