Home › Engine / Hybrid System · 1NZ-FE › ENGINE CONTROL › 1NZ-FE SFI SYSTEM

DTC    P0031    Oxygen Sensor Heater Control Circuit Low (Bank 1 Sensor 1)

DTC    P0032    Oxygen Sensor Heater Control Circuit High (Bank 1 Sensor 1)

DTC    P0037    Oxygen Sensor Heater Control Circuit Low (Bank 1 Sensor 2)

DTC    P0038    Oxygen Sensor Heater Control Circuit High (Bank 1 Sensor 2)

for Preparation Click here


DESCRIPTION

The heated oxygen sensor is used to monitor the oxygen concentration in the exhaust gas. For optimum catalytic converter operation, the air-fuel mixture must be maintained near the ideal stoichiometric air-fuel ratio. The heated oxygen sensor output voltage changes suddenly in the vicinity of the stoichiometric air-fuel ratio. The ECM adjusts the fuel injection time so that the air-fuel ratio is nearly stoichiometric. The heated oxygen sensor generates a voltage between 0 and 1V in response to the oxygen concentration in the exhaust gas.
If the oxygen concentration in the exhaust gas increases, the air-fuel ratio is described as lean. The heated oxygen sensor voltage drops to below 0.45 V and the heated oxygen sensor informs the ECM of the lean condition. If there is little oxygen in the exhaust gas, the air-fuel ratio is described as rich. The heated oxygen sensor voltage increases to above 0.45 V and the heated oxygen sensor informs the ECM of the rich condition.

A112653E01

HINT:
  1. Sensor 1 refers to the sensor mounted in front of the Three-Way Catalytic Converter (TWC) and located near the engine assembly.
  2. Sensor 2 refers to the sensor mounted behind the TWC and located far from the engine assembly.


A254131E01


A259951E01


DTC No.
DTC Detection Condition
Trouble Area
P0031
P0037
Heated oxygen sensor heater current below 0.25 A when heater operates with +B greater than 10.5 V
(1 trip detection logic)
  1. Open in Heated oxygen sensor heater circuit
  2. Heated oxygen sensor heater
  3. No. 1 integration relay (EFI MAIN relay)
  4. ECM
P0032
P0038
Heated oxygen sensor heater current exceeds 2 A when heater operates
(1 trip detection logic)
  1. Short in Heated oxygen sensor heater circuit
  2. Heated oxygen sensor heater
  3. No. 1 integration relay (EFI MAIN relay)
  4. ECM

MONITOR DESCRIPTION

The sensing portion of the heated oxygen sensor has a zirconia element which is used to detect the oxygen concentration in the exhaust. If the zirconia element is at the proper temperature and the difference in the oxygen concentration between the inside and outside surface of the sensor is large, the zirconia element will generate voltage signals. In order to increase the oxygen concentration detecting capacity in the zirconia element, the ECM supplements the heat from the exhaust with heat from a heating element inside the sensor. When the current in the heated oxygen sensor heater is out of the standard operating range, the ECM interprets this as a fault in the heated oxygen sensor heater. The ECM illuminates the MIL and stores a DTC.
Example: The ECM stores either DTC P0032 or P0038 when the current in the heated oxygen sensor heater is more than 2 A despite the heater being OFF. Conversely, when the heater current is less than 0.25 A despite the heater being ON, DTC P0031 or P0037 is stored.

MONITOR STRATEGY


Required Sensors/Components (Main)
Heated oxygen sensor heater
Required Sensors/Components (Related)
Vehicle speed sensor
Frequency of Operation
Continuous

TYPICAL ENABLING CONDITIONS


Battery voltage
10.5 V or more
Engine
Running
Starter
OFF

P0031 and P0037 
Duration of following conditions
2 seconds or more
Learned heater current during heater OFF
Completed

P0032 and P0038 
Duration of following conditions
0.1 seconds or more
Learned heater current during heater OFF
Completed

TYPICAL MALFUNCTION THRESHOLDS


P0031 and P0037 
Heated oxygen sensor heater current when heated oxygen sensor heater ON
Less than 0.25 A

P0032 and P0038 
Heated oxygen sensor heater current when heated oxygen sensor heater OFF
More than 2 A

COMPONENT OPERATING RANGE


Heated oxygen sensor heater current
0.25 to 2 A (when idling with warm engine and battery voltage 11 to 14 V)

CONFIRMATION DRIVING PATTERN


A198819E42

  1. Connect the intelligent tester to the DLC3.
  2. Turn the ignition switch to ON and turn the tester on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the tester on [A].
  6. Start the engine and idle it for 5 minutes or more [B].
  7. With the vehicle stationary, depress the accelerator pedal and maintain an engine speed of 3000 rpm for 1 minute [C].
  8. Idle the engine for 5 minutes or more [D].
  9. Enter the following menus: Powertrain / Engine and ECT / DTC [E].
  10. Read DTCs.

    HINT:
    1. If a DTC is output, the system is malfunctioning.
    2. If a DTC is not output, perform the following procedure.

  11. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  12. Input the DTC: P0031, P0032, P0037 or P0038.
  13. Check the DTC judgment result.

    Tester Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

HINT:
  1. If the judgment result shows NORMAL, the system is normal.
  2. If the judgment result shows ABNORMAL, the system has a malfunction.
  3. If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [E] again.


WIRING DIAGRAM


A254074E01


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
  1. Sensor 1 refers to the sensor closest to the engine assembly.
  2. Sensor 2 refers to the sensor farthest away from the engine assembly.
  3. Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  4. Change the fuel injection volume using the Control the Injection Volume function provided in the Active Test and monitor the heated oxygen sensor output voltage . If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.

1.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)
  1. Inspect heated oxygen sensor.

    HINT:
    1. For the heated oxygen sensor (sensor 1) inspection, refer to the following procedures (Click here).
    2. For the heated oxygen sensor (sensor 2) inspection, refer to the following procedures (Click here).



NG
REPLACE HEATED OXYGEN SENSOR (SENSOR 1) (Click here)

NG
REPLACE HEATED OXYGEN SENSOR (SENSOR 2) (Click here)
OK


2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF HEATED OXYGEN SENSOR HEATER)


    A258725E01
  1. Disconnect the heated oxygen sensor (sensor 1 and 2) connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage (for sensor 1):
    Tester Connection
    Switch Condition
    Specified Condition
    B37-2 (+B) - Body ground
    Ignition switch ON
    11 to 14 V

    Standard Voltage (for sensor 2):
    Tester Connection
    Switch Condition
    Specified Condition
    F80-2 (+B) - Body ground
    Ignition switch ON
    11 to 14 V

Text in Illustration 
*a
Front view of wire harness connector
(to Heated Oxygen Sensor)
*b
for sensor 1
*c
for sensor 2


NG
Go to step 5
OK


3.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)
  1. Disconnect the heated oxygen sensor (sensor 1 and 2) connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (for sensor 1):

    Tester Connection
    Condition
    Specified Condition
    B37-1 (HT1A) - B84-109 (HT1A)
    Always
    Below 1 Ω
    B37-1 (HT1A) or B84-109 (HT1A) - Body ground
    Always
    10 kΩ or higher


    Standard Resistance (for sensor 2):

    Tester Connection
    Condition
    Specified Condition
    F80-1 (HT1B) - B84-47 (HT1B)
    Always
    Below 1 Ω
    F80-1 (HT1B) or B84-47 (HT1B) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0031, P0032, P0037 OR P0038)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Clear DTCs (Click here).

  1. Start the engine.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC P0031, P0032, P0037 or P0038 are output
    B



B
REPLACE ECM (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

5.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - NO. 1 INTEGRATION RELAY)
  1. Disconnect the heated oxygen sensor (sensor 1 and 2) connector.

  1. Remove the No. 1 integration relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (for sensor 1):

    Tester Connection
    Condition
    Specified Condition
    B37-2 (+B) - 1E-4
    Always
    Below 1 Ω
    B37-2 (+B) or 1E-4 - Body ground
    Always
    10 kΩ or higher


    Standard resistance (for sensor 2):

    Tester Connection
    Condition
    Specified Condition
    F80-2 (+B) - 1D-11
    Always
    Below 1 Ω
    F80-2 (+B) or 1D-11 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CHECK ECM POWER SOURCE CIRCUIT (Click here)