Home › Power Source / Network · NETWORKING › CAN COMMUNICATION SYSTEM (for Separate Type Yaw Rate Sensor)

CAN COMMUNICATION SYSTEM (for Separate Type Yaw Rate Sensor) > Check CAN Bus Lines for Short Circuit

for Preparation Click here


DESCRIPTION

There may be a short circuit between the CAN bus lines when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 54 Ω.

Symptom
Trouble Area
The resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 54 Ω.
  1. Short between CAN bus lines
  2. ECM
  3. Combination meter assembly
  4. Airbag sensor assembly
  5. Skid control ECU (brake actuator assembly)
  6. Main body ECU (multiplex network body ECU)
  7. Power steering ECU assembly
  8. Steering angle sensor (spiral cable sub-assembly)
  9. Yaw rate sensor
  10. Air conditioning amplifier assembly
  11. No. 1 junction connector
  12. No. 2 junction connector

WIRING DIAGRAM


E236735E01


E236736E01


INSPECTION PROCEDURE

NOTICE:
  1. Turn the ignition switch off before measuring the resistances of the CAN main wire and the CAN branch wire.
  2. After the ignition switch is turned off, check that the key reminder warning system and light reminder warning system are not in operation.
  3. Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If doors need to be opened in order to check connectors, open the doors and leave them open.

HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

1.CHECK SHORT IN CAN BUS WIRES (DLC3 BRANCH WIRE)
  1. Turn the ignition switch off.

  1. Disconnect the F83 No. 2 junction connector.



    C152423E05
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    F4-6 (CANH) - F4-14 (CANL)
    Ignition switch off
    1 MΩ or higher

    Text in Illustration 
    *a
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (DLC3 BRANCH WIRE)
OK


2.CONNECT CONNECTOR
  1. Reconnect the F83 No. 2 junction connector.


NEXT


3.CHECK SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR)
  1. Disconnect the A61 and F82 No. 1 junction connectors.



    C152423E05
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    F4-6 (CANH) - F4-14 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Front view of DLC3



NG
Go to step 7
OK


4.CHECK SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - ECM)


    E219745E21
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A61-9 (CANH) - A61-20 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)



NG
Go to step 15
OK


5.CHECK SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY))


    E219745E29
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A61-10 (CANH) - A61-21 (CANL)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)



NG
Go to step 16
OK


6.CHECK SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))


    E219745E34
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    F82-1 (CANH) - F82-12 (CANL)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)



NG
Go to step 17
OK

REPLACE NO. 1 JUNCTION CONNECTOR 

7.CHECK SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)
  1. Disconnect the F83 No. 2 junction connector.



    E219745E28
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    F82-4 (CANH) - F82-15 (CANL)
    Ignition switch off
    1 MΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)



NG
REPAIR OR REPLACE CAN BUS MAIN WIRE OR CONNECTOR (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)
OK


8.CONNECT CONNECTOR
  1. Reconnect the A61 and F82 No. 1 junction connectors.


NEXT


9.CHECK SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)


    E219745E20
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    F83-7 (CANH) - F83-18 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)



NG
Go to step 18
OK


10.CHECK SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)


    E219745E24
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    F83-8 (CANH) - F83-19 (CANL)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)



NG
Go to step 19
OK


11.CHECK SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - STEERING ANGLE SENSOR (SPIRAL CABLE SUB-ASSEMBLY))


    E219745E25
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    F83-1 (CANH) - F83-12 (CANL)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)



NG
Go to step 20
OK


12.CHECK SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - YAW RATE SENSOR)


    E219745E52
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    F83-9 (CANH) - F83-20 (CANL)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)



NG
Go to step 21
OK


13.CHECK SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - POWER STEERING ECU ASSEMBLY)


    E219745E36
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    F83-6 (CANH) - F83-17 (CANL)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)



NG
Go to step 22
OK


14.CHECK SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - AIRBAG SENSOR ASSEMBLY)


    E219745E27
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    F83-4 (CANH) - F83-15 (CANL)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)



NG
Go to step 23
OK

REPLACE NO. 2 JUNCTION CONNECTOR 

15.CHECK SHORT IN CAN BUS WIRES (ECM MAIN WIRE)
  1. Disconnect the A74 ECM connector.



    E219745E21
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A61-9 (CANH) - A61-20 (CANL)
    Ignition switch off
    1 MΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)
    Result 
    Result
    Proceed to
    NG
    A
    OK (for 1NZ-FE)
    B
    OK (for 2NZ-FE)
    C



B
REPLACE ECM (Click here)

C
REPLACE ECM (Click here)
A

REPAIR OR REPLACE CAN BUS MAIN WIRE OR CONNECTOR (ECM MAIN WIRE) 

16.CHECK SHORT IN CAN BUS WIRES (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) BRANCH WIRE)
  1. Disconnect the A54 skid control ECU (brake actuator assembly) connector.



    E219745E29
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A61-10 (CANH) - A61-21 (CANL)
    Ignition switch off
    1 MΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)



NG
REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) BRANCH WIRE)
OK

REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) (Click here)  

17.CHECK SHORT IN CAN BUS WIRES (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) BRANCH WIRE)
  1. Disconnect the F76 main body ECU (multiplex network body ECU) connector.



    E219745E34
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    F82-1 (CANH) - F82-12 (CANL)
    Ignition switch off
    1 MΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)



NG
REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) BRANCH WIRE)
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)  

18.CHECK SHORT IN CAN BUS WIRES (COMBINATION METER ASSEMBLY MAIN WIRE)
  1. Disconnect the F1 combination meter assembly connector.



    E219745E20
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    F83-7 (CANH) - F83-18 (CANL)
    Ignition switch off
    1 MΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)



NG
REPAIR OR REPLACE CAN BUS MAIN WIRE OR CONNECTOR (COMBINATION METER ASSEMBLY MAIN WIRE)
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)  

19.CHECK SHORT IN CAN BUS WIRES (AIR CONDITIONING AMPLIFIER ASSEMBLY BRANCH WIRE)
  1. Disconnect the F42*1 or F41*2 air conditioning amplifier assembly connector.

*1: for Automatic Air Conditioning System
*2: for Manual Air Conditioning System


    E219745E24
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    F83-8 (CANH) - F83-19 (CANL)
    Ignition switch off
    1 MΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)



NG
REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY BRANCH WIRE)
OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)  

20.CHECK SHORT IN CAN BUS WIRES (STEERING ANGLE SENSOR (SPIRAL CABLE SUB-ASSEMBLY) BRANCH WIRE)
  1. Disconnect the F30 steering angle sensor (spiral cable sub-assembly) connector.



    E219745E25
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    F83-1 (CANH) - F83-12 (CANL)
    Ignition switch off
    1 MΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)



NG
REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (STEERING ANGLE SENSOR (SPIRAL CABLE SUB-ASSEMBLY) BRANCH WIRE)
OK

REPLACE STEERING ANGLE SENSOR (SPIRAL CABLE SUB-ASSEMBLY) (Click here)  

21.CHECK SHORT IN CAN BUS WIRES (YAW RATE SENSOR BRANCH WIRE)
  1. Disconnect the F122 yaw rate sensor connector.



    E219745E52
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    F83-9 (CANH) - F83-20 (CANL)
    Ignition switch off
    1 MΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)



NG
REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (YAW RATE SENSOR BRANCH WIRE)
OK

REPLACE YAW RATE SENSOR (Click here)  

22.CHECK SHORT IN CAN BUS WIRES (POWER STEERING ECU ASSEMBLY BRANCH WIRE)
  1. Disconnect the F6 power steering ECU assembly connector.



    E219745E36
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    F83-6 (CANH) - F83-17 (CANL)
    Ignition switch off
    1 MΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)



NG
REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (POWER STEERING ECU ASSEMBLY BRANCH WIRE)
OK

REPLACE POWER STEERING ECU ASSEMBLY (Click here)  

23.CHECK SHORT IN CAN BUS WIRES (AIRBAG SENSOR ASSEMBLY BRANCH WIRE)
  1. Disconnect the F16 airbag sensor assembly connector.



    E219745E27
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    F83-4 (CANH) - F83-15 (CANL)
    Ignition switch off
    1 MΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)



NG
REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (AIRBAG SENSOR ASSEMBLY BRANCH WIRE)
OK

REPLACE AIRBAG SENSOR ASSEMBLY (Click here)