Home › Vehicle Interior › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM

POWER DOOR LOCK CONTROL SYSTEM > Only Back Door cannot be Opened

for Preparation Click here


DESCRIPTION

The main body ECU receives signals from the back door opener switch assembly. Then, the main body ECU activates the back door lock motor.

WIRING DIAGRAM


B288674E01


INSPECTION PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (DOOR LOCK STATUS)
  1. Unlock all doors.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Main Body / Data List.

  1. According to the display on the intelligent tester, read the Data List.


Main Body 
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Back Door Open
Back door open status / Prohibit or Permit
Prohibit: Back door locked
Permit: Back door unlocked
-

OK:
The intelligent tester indicates Permit according to the door lock operation shown in the table.



NG
REPLACE MAIN BODY ECU (Click here)
OK


2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Main Body / Active Test.

  1. According to the display on the intelligent tester, perform the Active Test.

    Main Body 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Trunk and Back-Door Open
    Back door lock motor
    OFF / ON
    -

    OK:
    The back door lock assembly unlatches when ON is selected.



NG
Go to step 4
OK


3.READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Main Body / Data List.

  1. According to the display on the intelligent tester, read the Data List.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Back Door Open Handle SW
    Back door opener switch signal / OFF or ON
    OFF: Back door opener switch not pushed
    ON: Back door opener switch pushed
    -

    OK:
    The intelligent tester indicates ON or OFF according to the switch operation shown in the table.



NG
Go to step 7
OK

REPLACE MAIN BODY ECU (Click here)  

4.INSPECT BACK DOOR LOCK ASSEMBLY
  1. Inspect the back door lock assembly (Click here).



NG
REPLACE BACK DOOR LOCK ASSEMBLY (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (BACK DOOR LOCK ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
  1. Disconnect the P12 back door lock assembly connector.

  1. Disconnect the 3D instrument panel junction block assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    P12-1 (ACT+) - 3D-9 (ACT+)
    Always
    Below 1 Ω
    P12-2 (ACT-) - Body ground
    Always
    Below 1 Ω
    P12-1 (ACT+) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

B289456E02


Text in Illustration 
*A
for LHD
*B
for RHD
*a
Component without harness connected
(Instrument Panel Junction Block Assembly)
-
-
  1. Remove the instrument panel junction block assembly (Click here).

  1. Remove the main body ECU.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    3E-1 - 3D-9
    Always
    10 kΩ or higher
    3E-1 - MB-6 (TR+)
    Always
    Below 1 Ω
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    3F-1 - 3D-9
    Always
    10 kΩ or higher
    3F-1 - MB-6 (TR+)
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    3D-9 - Body ground
    Battery positive (+) → 3E-1
    Battery negative (-) → MB-6
    11 to 14 V
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    3D-9 - Body ground
    Battery positive (+) → 3F-1
    Battery negative (-) → MB-6
    11 to 14 V



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (Click here)
OK

REPLACE MAIN BODY ECU (Click here)  

7.INSPECT BACK DOOR OPENER SWITCH ASSEMBLY
  1. Inspect the back door opener switch assembly (Click here).



NG
REPLACE BACK DOOR OPENER SWITCH ASSEMBLY (Click here)
OK


8.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BACK DOOR OPENER SWITCH ASSEMBLY)
  1. Disconnect the F76 main body ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F76-23 (BDSU) - P8-3 (B)
    Always
    Below 1 Ω
    P8-2 (L) - Body ground
    Always
    Below 1 Ω
    P8-3 (B) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (Click here)