Home › Engine / Hybrid System · 1NZ-FE › ENGINE CONTROL › 1NZ-FE SFI SYSTEM

1NZ-FE SFI SYSTEM > Fuel Pump Control Circuit

for Preparation Click here


DESCRIPTION

When the engine is cranked, the ST (Starter) relay drive signal is input to the STA terminal of the ECM, and NE signal generated by the crankshaft position sensor is also input to the NE+ terminal. Thus, the ECM interprets that the engine has been cranked, and turns the transistor Tr1 in the ECM internal circuit ON. The current flows to the C/OPN (Circuit Opening) relay by turning the Tr1 ON. Then, the fuel pump operates. While the NE signal is input to the ECM with the engine running, the ECM turns the Tr1 on continuously.

WIRING DIAGRAM


A254129E03


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP/SPD)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel pump/Speed.

  1. Check whether the fuel pump operating sound occurs when performing the Active Test on the tester.


Result 
Result
Proceed to
Fuel pump operating sound does not occur
A
Fuel pump operating sound occurs
B


B
Go to step 6
A


2.INSPECT NO. 1 INTEGRATION RELAY (C/OPN RELAY)
  1. Inspect the No. 1 integration relay (C/OPN relay) (Click here).



NG
REPLACE NO.1 INTEGRATION RELAY (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM)
  1. Remove the No. 1 integration relay from the engine room relay block.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.


Standard Resistance:

Tester Connection
Condition
Specified Condition
1E-11 - A74-7 (FC)
Always
Below 1 Ω
1E-11 or A74-7 (FC) - Body ground
Always
10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - FUEL PUMP - BODY GROUND)
  1. Remove the No. 1 integration relay from the engine room relay block.

  1. Disconnect the fuel pump connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    1E-5 - K17-4
    Always
    Below 1 Ω
    K17-5 - Body ground
    Always
    Below 1 Ω
    1E-5 or K17-4 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.INSPECT FUEL PUMP
  1. Inspect the fuel pump (Click here).



NG
REPLACE FUEL PUMP (Click here)
OK

REPLACE ECM (Click here)  

6.READ VALUE USING INTELLIGENT TESTER (STARTING SIGNAL)
  1. Connect the intelligent tester to the DLC3.

  1. turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.

  1. Check the result when the ignition switch is ON and the engine starts.

    OK:

    Ignition Switch Condition
    Starter Signal
    ON
    OFF
    START
    ON



NG
CHECK STARTER SIGNAL CIRCUIT (Click here)
OK


7.READ VALUE USING INTELLIGENT TESTER (ENGINE SPEED)
  1. Connect the intelligent tester to the DLC3.

  1. turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.

  1. Read the values displayed on the tester while cranking.

    OK:
    Values are displayed continuously.



NG
CHECK CRANKSHAFT POSITION SENSOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)