Home › BRAKE › BRAKE CONTROL › VEHICLE STABILITY CONTROL SYSTEM

DTC    C0200/31    Front Speed Sensor RH Circuit

DTC    C0205/32    Front Speed Sensor LH Circuit

DTC    C1235/35    Foreign Object is Attached on Tip of Front Speed Sensor RH

DTC    C1236/36    Foreign Object is Attached on Tip of Front Speed Sensor LH

for Preparation Click here


DESCRIPTION

The speed sensor detects wheel speed and sends the appropriate signals to the ECU. These signals are used to control the ABS, BA, TRAC, A-TRAC, VSC, AUTO LSD, DAC and HAC control systems. This speed sensor contains a sensor IC, which consists of 2 MREs (Magnetic Resistance Element). The speed sensor rotor, which consists of 48 sets of N and S poles that are arranged in a circle, is integrated with the inner race of the hub bearing.
To detect the rotation direction, the output waves are used to determine the relationship of the pulses that are generated by 2 MREs. Upon receiving this signal, the sensor IC outputs a forward or backward wave to the ECU.
I042838E01

DTC No.
DTC Detection Condition
Trouble Area
C0200/31
C0205/32
When any of the following conditions is detected:
1. At a vehicle speed of 6 mph (10 km/h) or more, pulses are not input for 1 second.
2. Momentary interruption of the speed sensor signal occurs at least 255 times when switching the ignition switch ON and OFF.
3. Continuous noise occurs in speed sensor signals at a vehicle speed of 12 mph (20 km/h) or more.
4. Speed sensor signal circuit is open for 0.12 seconds or more.
5. 3 of the wheel sensors detect normal reversing signals, and the other wheel sensor detects malfunction signals 75 times with IG ON while reversing at 3 km/h.
6. Rotating direction of each wheel changes 7 times within 0.006 seconds with IG ON while driving at 10 km/h or more.
7. Rotating direction of one of the wheels is not the same as that of the other wheels for 1 second while driving at 30 km/h or more.
8. Reversing signal is output for 1 second or more while driving at 100 km/h or more.
9. Rotating direction of one of the wheels is not detected normally, and the rotating direction of each of the other wheels is not the same for 1 second while driving at 30 km/h or more.
  1. Right front and left front speed sensor
  2. Each speed sensor circuit
  3. Speed sensor rotor
  4. Sensor installation
  5. Master cylinder solenoid
C1235/35
C1236/36
Continuous noise occurs in speed sensor signals when vehicle speed is 12 mph (20 km/h) or more for 5 seconds or more.
  1. Right front and left front speed sensor
  2. Speed sensor rotor
  3. Sensor installation
  4. Master cylinder solenoid

HINT:
  1. DTC C0200/31 and C1235/35 are for the right front speed sensor.
  2. DTC C0205/32 and C1236/36 are for the left front speed sensor.


WIRING DIAGRAM


C114554E04


INSPECTION PROCEDURE

NOTICE:
When replacing the master cylinder solenoid, perform zero point calibration (Click here).

1.READ VALUE OF INTELLIGENT TESTER (MOMENTARY INTERRUPTION OF FRONT SPEED SENSOR)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to the ON position and push the intelligent tester main switch ON.

  1. Select "DATA LIST" mode on the intelligent tester.

    Item
    Measurement Item / Range
    (Display)
    Normal Condition
    Diagnostic Note
    SPD SEN FR
    Speed sensor open detection (FR)/OPN DET or NORMAL
    OPN DET: Momentary interruption
    NORMAL: Normal
    -
    SPD SEN FL
    Speed sensor open detection (FL)/OPN DET or NORMAL
    OPN DET: Momentary interruption
    NORMAL: Normal
    -

  1. Check for any momentary interruption in the wire harness and connector corresponding to a DTC (Click here).

    OK:
    There are no momentary interruptions.

HINT:
Perform the above inspection before removing the sensor and connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (SPEED SENSOR CIRCUIT)
OK


2.READ VALUE OF INTELLIGENT TESTER (FRONT SPEED SENSOR)

Item
Measurement Item / Range
(Display)
Normal Condition
Diagnostic Note
WHEEL SPD FR
Wheel speed sensor (FR) reading /Min.: 0 mph (0 km/h), Max.: 202 mph (326 km/h)
Actual wheel speed
Similar speed as indicated on speedometer
WHEEL SPD FL
Wheel speed sensor (FL) reading/ Min.: 0 mph (0 km/h), Max.: 202 mph (326 km/h)
Actual wheel speed
Similar speed as indicated on speedometer
  1. Check that there is no difference between the speed value output from the speed sensor displayed on the intelligent tester and the speed value displayed on the speedometer when driving the vehicle.

    OK:
    The speed value output from the speed sensor displayed on the intelligent tester is the same as the actual vehicle speed.



NG
Go to step 4
OK


3.PERFORM TEST MODE (SIGNAL CHECK)
  1. Check if test mode (signal check) DTCs are detected.

    Result:

    Condition
    Proceed to
    Test mode (signal check) DTC is output
    A
    Test mode (signal check) DTC is not output
    B



B
Go to step 10
A


4.INSPECT FRONT SPEED SENSOR INSTALLATION


    I044006E04
  1. Check the speed sensor installation.

    OK:
    The installation bolt is tightened properly.
    There is no clearance between the sensor and the front steering knuckle.

Torque:
8.3 N*m{ 85 kgf*cm , 73 in.*lbf }

NOTICE:
Check the speed sensor signal after replacement (Click here).



NG
INSTALL FRONT SPEED SENSOR CORRECTLY
OK


5.INSPECT SPEED SENSOR TIP
  1. Remove the front speed sensor (Click here).

  1. Check the sensor tip.

    OK:
    No scratches or foreign matter on the sensor tip.

    NOTICE:
    Check the speed sensor signal after cleaning/replacement (Click here).



NG
CLEAN OR REPLACE FRONT SPEED SENSOR
OK


6.INSPECT FRONT SPEED SENSOR


    I045651E01
  1. Install the front speed sensor.

  1. Turn the ignition switch off.

  1. Disconnect the front speed sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    RH:
    Tester Connection
    Specified Condition
    A10-2 (FR+) - Body ground
    10 kΩ or higher
    A10-1 (FR-) - Body ground
    10 kΩ or higher
    LH:
    Tester Connection
    Specified Condition
    A9-2 (FL+) - Body ground
    10 kΩ or higher
    A9-1 (FL-) - Body ground
    10 kΩ or higher



NG
REPLACE FRONT SPEED SENSOR
OK


7.INSPECT SKID CONTROL SENSOR WIRE


    I044003E01
  1. Disconnect the skid control sensor wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    RH:
    Tester Connection
    Specified Condition
    A10 ("A"-2) - A10 ("B"-2)
    Below 1 Ω
    A10 ("A"-2) - A10 ("B"-1)
    10 kΩ or higher
    A10 ("A"-2) - Body ground
    10 kΩ or higher
    A10 ("A"-1) - A10 ("B"-1)
    Below 1 Ω
    A10 ("A"-1) - A10 ("B"-2)
    10 kΩ or higher
    A10 ("A"-1) - Body ground
    10 kΩ or higher
    LH:
    Tester Connection
    Specified Condition
    A9 ("A"-2) - A9 ("B"-2)
    Below 1 Ω
    A9 ("A"-2) - A9 ("B"-1)
    10 kΩ or higher
    A9 ("A"-2) - Body ground
    10 kΩ or higher
    A9 ("A"-1) - A9 ("B"-1)
    Below 1 Ω
    A9 ("A"-1) - A9 ("B"-2)
    10 kΩ or higher
    A9 ("A"-1) - Body ground
    10 kΩ or higher

    NOTICE:
    Check the speed sensor signal after replacement (Click here).



NG
REPLACE SKID CONTROL SENSOR WIRE
OK


8.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - FRONT SPEED SENSOR)


    I045084E02
  1. Disconnect the skid control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    RH:
    Tester Connection
    Specified Condition
    S28-3 (FR+) - A10-2 (FR+)
    Below 1 Ω
    S28-3 (FR+) - Body ground
    10 kΩ or higher
    S28-17 (FR-) - A10-1 (FR-)
    Below 1 Ω
    S28-17 (FR-) - Body ground
    10 kΩ or higher
    LH:
    Tester Connection
    Specified Condition
    S28-18 (FL+) - A9-2 (FL+)
    Below 1 Ω
    S28-18 (FL+) - Body ground
    10 kΩ or higher
    S28-4 (FL-) - A9-1 (FL-)
    Below 1 Ω
    S28-4 (FL-) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9.INSPECT MASTER CYLINDER SOLENOID


    I045852E02
  1. Reconnect the skid control ECU connector.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    RH:
    Tester Connection
    Specified Condition
    A10-2 (FR+) - Body ground
    7.5 to 12 V
    LH:
    Tester Connection
    Specified Condition
    A9-2 (FL+) - Body ground
    7.5 to 12 V



NG
REPLACE MASTER CYLINDER SOLENOID
OK


10.RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Drive the vehicle at a speed of approximately 20 mph (32 km/h) or more for 60 seconds or more.

  1. Check if the same pending DTCs are detected (Click here).

    HINT:
    Reinstall the sensors, connectors, etc. and restore the previous vehicle conditions before rechecking for DTCs.


    Result:

    Condition
    Proceed to
    DTC is output
    A
    DTC is not output (When troubleshooting in accordance with the DTC CHART.)
    B
    DTC is not output (When troubleshooting in accordance with the PROBLEM SYMPTOMS TABLE.)
    C



B
END

C
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE
A


11.REPLACE FRONT SPEED SENSOR
  1. Replace the front speed sensor (Click here).

    NOTICE:
    Check the speed sensor signal after replacement (Click here).


NEXT


12.RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Drive the vehicle at a speed of approximately 20 mph (32 km/h) or more for 60 seconds or more.

  1. Check if the same pending DTCs are detected (Click here).

    HINT:
    Reinstall the sensors, connectors, etc. and restore the previous vehicle conditions before rechecking for DTCs.


    Result:

    Condition
    Proceed to
    DTC is output
    A
    DTC is not output
    B



B
END
A


13.INSPECT SPEED SENSOR ROTOR
  1. Remove the front axle with ABS rotor bearing assembly (Click here for 2WD, or Click here for 4WD).

  1. Check the sensor rotor.

    OK:
    No scratches, oil, or foreign matter on the rotors.

    NOTICE:
    Check the speed sensor signal after cleaning/replacement (Click here).



NG
CLEAN OR REPLACE FRONT AXLE ABS ROTOR BEARING ASSEMBLY (SPEED SENSOR ROTOR)
OK

REPLACE MASTER CYLINDER SOLENOID