Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM
RM1440E _51 Engine / Hybrid System _056124 1GR-FE ENGINE CONTROL _0273876 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0340  Camshaft Position Sensor Circuit Malfunction  P0342  Camshaft Position Sensor "A" Circuit Low Input (Bank 1 or Single Sensor)  P0343  Camshaft Position Sensor "A" Circuit High Input (Bank 1 or Single Sensor)  P0345  Camshaft Position Sensor "A" Circuit (Bank 2)  P0347  Camshaft Position Sensor "A" Circuit Low Input (Bank 2)  P0348  Camshaft Position Sensor "A" Circuit High Input (Bank 2)  


DESCRIPTION

The intake camshaft's Variable Valve Timing (VVT) sensor (VV1, VV2 signal) consists of a magnet and MRE (Magnetoresistive Element).

The camshaft timing gear has a sensor plate with 3 teeth on its outer circumference. When the gear rotates, changes occur in the air gaps between the sensor plate and MRE, which affects the magnetic field. As a result, the resistance of the MRE material fluctuates. The VVT sensor converts the gear rotation data to pulse signals, uses the pulse signals to determine the camshaft angle, and sends the camshaft angle data to the ECM.

The crankshaft position sensor plate has 34 teeth. The pickup coil generates 34 signals for each crankshaft revolution. Based on a combination of the VVT signal and NE signal, the ECM detects the crankshaft angle. Then the ECM uses this data to control fuel injection time and injection timing. Also, based on the NE signal, the ECM detects the engine speed.

DTC No. DTC Detection Condition Trouble Area
P0340 Either condition is met:
·

No VVT sensor signal is sent to the ECM while cranking (2 trip detection logic).

·

There is no VVT sensor signal despite the crankshaft position sensor input being normal at an engine speed of 600 rpm or more (1 trip detection logic).


·

Open or short in VVT sensor circuit for intake camshaft

·

VVT sensor for intake camshaft

·

Camshaft timing gear for intake camshaft

·

Timing chain for intake camshaft has jumped tooth

·

ECM


P0345 There is no VVT sensor signal despite the crankshaft position sensor input being normal at an engine speed of 600 rpm or more (1 trip detection logic).
·

Open or short in VVT sensor circuit for intake camshaft

·

VVT sensor for intake camshaft

·

Camshaft timing gear for intake camshaft

·

Timing chain for intake camshaft has jumped tooth

·

ECM


P0342
P0347
Output voltage of the VVT sensor is below 0.3 V for 4 seconds (1 trip detection logic).
·

Open or short in VVT sensor circuit for intake camshaft

·

VVT sensor for intake camshaft

·

Camshaft timing gear for intake camshaft

·

Timing chain for intake camshaft has jumped tooth

·

ECM


P0343
P0348
Output voltage of the VVT sensor is higher than 4.7 V for 4 seconds (1 trip detection logic).
·

Open or short in VVT sensor circuit for intake camshaft

·

VVT sensor for intake camshaft

·

Camshaft timing gear for intake camshaft

·

Timing chain for intake camshaft has jumped tooth

·

ECM



A199235E01
1.292,2.8 2.322,3.001 1.031,0.201 10 20 msec./DIV. 0.149,0.864 0.832,1.065 0.684,0.201 10 5 V/DIV. 0.174,1.448 0.458,1.649 0.284,0.201 10 NE 0.088,1.947 0.455,2.148 0.367,0.201 10 VV1 3.01,1.465 3.342,1.666 0.332,0.201 10 GND 3.01,2.067 3.342,2.268 0.332,0.201 10 GND 3.01,2.462 3.342,2.663 0.332,0.201 10 GND 0.088,2.342 0.455,2.543 0.367,0.201 10 VV2 0.329,0.245 2.735,0.446 2.406,0.201 10 VV1, VV2 and NE Signal Waveforms

Reference: Inspection using an oscilloscope

HINT:
·

The correct waveforms are as shown.

·

VV1+ and VV2+ are the VVT sensor signals, and NE+ is the crankshaft position sensor signal.



Item Content
Terminal NE+ - NE-
VV1+ - VV1-
VV2+ - VV2-
Equipment Setting 5 V/DIV.
20 msec./DIV.
Condition Cranking or idling


MONITOR DESCRIPTION

If no signal is transmitted by the VVT sensor despite the camshaft revolving, or the rotations of the camshaft and crankshaft are not synchronized, the ECM interprets this as a malfunction of the VVT sensor.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK TERMINAL VOLTAGE (SENSOR POWER SOURCE)
a.
U149588E01
0.492,0.997 0.759,1.160 0.267,0.163 10 B21 0.492,1.35 0.759,1.513 0.267,0.163 10 B22 2.317,1.684 2.593,1.847 0.276,0.163 10 VC 0.079,0.042 0.269,0.205 0.190,0.163 10 *a 1.96,1.346 2.274,1.674 false

Disconnect the VVT sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
B21-3 (VC) - Body ground Ignition switch ON 4.5 to 5.0 V
B22-3 (VC) - Body ground Ignition switch ON 4.5 to 5.0 V


Text in Illustration
*a Front view of wire harness connector
(to VVT Sensor)


c.

Reconnect the VVT sensor connector.



OK

2.CHECK HARNESS AND CONNECTOR (VVT SENSOR FOR INTAKE CAMSHAFT - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (VVT SENSOR FOR INTAKE CAMSHAFT - ECM)
a.

Disconnect the VVT sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B21-1 (VVR+) - B36-9 (VV1+) Always Below 1 Ω
B21-2 (VVR-) - B36-10 (VV1-) Always Below 1 Ω
B22-1 (VVL+) - B36-12 (VV2+) Always Below 1 Ω
B22-2 (VVL-) - B36-11 (VV2-) Always Below 1 Ω
B21-1 (VVR+) or B36-9 (VV1+) - Body ground Always 10 kΩ or higher
B21-2 (VVR-) or B36-10 (VV1-) - Body ground Always 10 kΩ or higher
B22-1 (VVL+) or B36-12 (VV2+) - Body ground Always 10 kΩ or higher
B22-2 (VVL-) or B36-11 (VV2-) - Body ground Always 10 kΩ or higher



d.

Reconnect the VVT sensor connector.


e.

Reconnect the ECM connector.



OK

3.CHECK SENSOR INSTALLATION (VVT SENSOR FOR INTAKE CAMSHAFT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK SENSOR INSTALLATION (VVT SENSOR FOR INTAKE CAMSHAFT)
a.
A388055E02
1.708,1.573 2.469,1.771 0.76,0.198 10 false Clearance 0.417,1.823 0.74,2.031 0.323,0.208 10 false OK 2.635,1.813 2.958,2.021 0.323,0.208 10 false NG

Check the VVT sensor installation.

OK:

Sensor is installed correctly.




OK

4.CHECK CAMSHAFT TIMING GEAR ASSEMBLY (TEETH OF PLATE)

NG

4.CHECK CAMSHAFT TIMING GEAR ASSEMBLY (TEETH OF PLATE)
a.

Check the teeth of the signal plate.

OK:

Sensor plate teeth do not have any cracks or deformation.




OK

5.REPLACE VVT SENSOR

NG

REPLACE CAMSHAFT TIMING GEAR ASSEMBLY

5.REPLACE VVT SENSOR

NEXT

6.CHECK WHETHER DTC OUTPUT RECURS
6.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.



e.

Start the engine.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Code / Pending.


g.

Read DTCs.

Result
Display (DTC Output) Proceed to
No output A
P0340, P0342, P0343, P0345, P0347 or P0348 B

HINT:

If the engine does not start, replace the ECM.




A

END

B