Refer to P0412 (See page Engine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>P0412).
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| P2445 | Both of the following conditions are met for 7 seconds (2 trip detection logic):
(a) Engine is running (b) Secondary air injection pressure is less than 1 kPa (7.5 mmHg) when secondary air injection is ON |
·
Air pump assembly ·
Open in air pump circuit ·
Air injection system piping ·
Pressure sensor ·
Open or short in pressure sensor circuit ·
Air injection control driver ·
ECM ·
Open or short in air pump heater circuit ·
Air pump heater relay (AIR PUMP HTR) |
The ECM monitors the pressure in the secondary air passage using the pressure sensor located on the emission control valve set of the secondary air injection system. The sensor measures the pressure in the secondary air passage and transmits a signal to the ECM.
If a malfunction is detected, the ECM illuminates the MIL and stores a DTC.
Example:
DTC P2445 mainly indicate a malfunction in which the air pump is stuck off.
This Secondary Air Injection Check only allows technicians to operate the secondary air injection system for a maximum of 5 seconds. Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks. While secondary air injection system operation using the GTS is prohibited, the GTS display indicates the prohibition (WAIT or ERROR). If ERROR is displayed on the GTS during the test, stop the engine for 10 minutes, and then try again.
Performing Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If it is necessary to repeat the check, leave an interval of several minutes between System Check operations to prevent the system from overheating.
When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
Turn the ignition switch off when the Secondary Air Injection Check operation finishes.
Start the engine and warm it up.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation) (See page Engine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.
Start the engine after the GTS initialization is finished.
Perform the System Check operation by pressing ENTER (Next).
Perform the following to confirm the secondary air injection system pending codes: Press ENTER (Exit).
Check for pending DTCs.
No pending DTC is output.
After Secondary Air Injection Check is completed, check All Readiness by entering the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P2445.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and the DTC judgment result again.
Turn the ignition switch off.
Refer to DTC P0412 (See page Engine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>P0412).
Refer to "Data List / Active Test" [Air Pump Pressure (Absolute), Air Pump2 Pressure (Absolute) and Air Pump Pulsation Pressure] (See page Engine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>DATA LIST / ACTIVE TEST).
Determination by ECM monitoring:
The ECM detects malfunctions in the secondary air injection system by detecting the pressure in the secondary air injection passage between the air pump and emission control valve and stores a DTC. Soon after a cold engine start, the monitor runs for a short time while the secondary air injection system is both ON and OFF. The ECM detects both the pressure and the exhaust pulsation and compares them.
The following 8 patterns are secondary air injection system pressure conditions in the secondary air injection system passage.
| Air Pump | ON |
| Emission Control Valve | Open |
| Pressure | 1 kPa or higher |
| Pulsation Detection | Exhaust gas pulsation detected |
| Air Pump | OFF |
| Emission Control Valve | Open |
| Pressure | Below 3 kPa |
| Pulsation Detection | Exhaust gas pulsation detected |
| Air Pump | ON |
| Emission Control Valve | Closed |
| Pressure | 1 kPa or higher |
| Pulsation Detection | Exhaust gas pulsation not detected |
| Air Pump | OFF |
| Emission Control Valve | Closed |
| Pressure | Below 3 kPa |
| Pulsation Detection | Exhaust gas pulsation not detected |
| Air Pump | ON |
| Emission Control Valve | Open |
| Pressure | 1 kPa or higher |
| Pulsation Detection | Exhaust gas pulsation detected |
| Air Pump | OFF |
| Emission Control Valve | Open |
| Pressure | Below 3 kPa |
| Pulsation Detection | Exhaust gas pulsation detected |
| Air Pump | ON |
| Emission Control Valve | Closed |
| Pressure | 1 kPa or higher |
| Pulsation Detection | Exhaust gas pulsation not detected |
| Air Pump | OFF |
| Emission Control Valve | Closed |
| Pressure | Below 3 kPa |
| Pulsation Detection | Exhaust gas pulsation not detected |
If the detected pressure is high, the air pump is assumed to be ON and if it alternates sharply, the emission control valve is assumed to be open. The ECM detects malfunctions from the combination of pressures detected when the secondary air injection system is ON and OFF.
The exhaust pulsation value is calculated in the ECM. If the calculated value exceeds a certain level, the ECM determines that the exhaust pulsation is in the secondary air injection system.
In cases 3 and 7, as the pressure sensor detects a slight pump operation pulsation, the detected value is not constant. Since the pump outlet is blocked by closing the emission control valve, the average pressure is higher than in case 1 (approximately 15 to 25 kPa).
In case 1, the average pressure is approximately 3 to 11 kPa. The value of 1 kPa indicated in the table above is a threshold for detecting pump malfunctions.
| Detected Condition while Secondary Air Injection Operating:
Air Pump ON, Emission Control Valve Open |
Detected Condition while Secondary Air Injection not Operating:
Air Pump OFF, Emission Control Valve Closed |
ECM Determination | DTC Output |
|---|---|---|---|
| Case 1 | Case 8 | Normal or emission control valve set stuck Closed | -
or P2441 or P2443 |
| Case 1 | Case 6 | Emission control valve set stuck open | P2440 and P2442
or P2442 |
| Case 1 | Case 7 | Normal | - |
| Case 2 | Case 8 | Air pump assembly stuck OFF | P2445 |
| Case 3 | Case 8 | Normal | - |
| Case 1 | Case 5 | Normal | - |
| Case 2 | Case 6 | Emission control valve stuck open and air pump stuck OFF | P2440 and/or P2442
and P2445 |
| Case 3 | Case 7 | Normal | - |
| Case 4 | Case 8 | Normal | - |
By using the GTS to perform the Secondary Air Injection Check operation in the System Check, the air-fuel ratio and the pressure in the secondary air injection system passage can be checked while the secondary air injection system is operating. This helps technicians to troubleshoot the system when it malfunctions. Furthermore, pending codes also can be checked by performing Utility / Secondary Air Injection Check / Automatic Mode after the repair.
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
System Check:
The pressure in the secondary air passage can be checked using the GTS.
Start the engine and warm it up.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV 1: OPEN, ASV 2: OPEN and AIR PUMP: OFF, ASV 1: CLOSE, ASV 2: CLOSE.
When Manual Mode is selected, the GTS initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.
Start the engine.
Perform the secondary air injection system forced operation while the engine is idling.
Check that the Data List values for the air pump (AIR PUMP), emission control valve (ASV) and pressure in the secondary air injection system passage (PRESSURE) displayed on the GTS are as shown in the table below.
| GTS Operation | Air Pump | Emission Control Valve | Pressure*1 | Pulsation*2 |
|---|---|---|---|---|
| AIR PUMP: ON, ASV: OPEN | ON | OPEN | 1 kPa or higher | 15 kPa or higher |
| AIR PUMP: OFF, ASV: CLOSE | OFF | CLOSE | Below 3 kPa | Below 25 kPa |
*1: Average pumping pressure (gauge pressure). The pressure should be 1 kPa or higher when the secondary air injection system operates.
*2: The cumulative exhaust pulsation calculated by the ECM. If the calculated value exceeds a certain level, the ECM determines that the exhaust pulsation is in the secondary air injection system.
Turn the ignition switch off.
This Secondary Air Injection Check only allows technicians to operate the secondary air injection system for a maximum of 5 seconds. Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks. While secondary air injection system operation using the GTS is prohibited, the GTS display indicates the prohibition (WAIT or ERROR). If ERROR is displayed on the GTS during the test, stop the engine for 10 minutes, and then try again.
Performing Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If it is necessary to repeat the check, leave an interval of several minutes between System Check operations to prevent the system from overheating.
When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
Turn the ignition switch off when the Secondary Air Injection Check operation finishes.
Bank 1 refers to the bank that includes the NO. 1 cylinder*.
*: The NO. 1 cylinder is the cylinder which is farthest from the transmission.
Bank 2 refers to the bank that does not include the NO. 1 cylinder.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
|---|---|
| P2445 is output | A |
| P2445 and other DTCs are output | B |
If any DTCs other than P2445 are output, troubleshoot those DTCs first.
A
B
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Read the values of Air Pump Freeze, Air Switching Valve Freeze and Air Switching Valve2 Freeze from the freeze frame data recorded previously.
Referring to the following table, proceed to the appropriate step according to the result of the data reading.
| Result | Proceed to | ||
|---|---|---|---|
| Air Pump Freeze | Air Switching Valve Freeze | Air Switching Valve2 Freeze | |
| OFF | OFF | OFF | B |
| Except above | A | ||
A
B
Disconnect the air pump connector.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT/ Active Test / Activate the Air Pump Heater.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A50-1 (APH+) - Body ground | Activate the Air Pump Heater is ON | 11 to 14 V |
| *a | Front view of wire harness connector
(to Air Pump Assembly) |
Reconnect the air pump connector.
OK
NG
Inspect the air pump assembly (See page Engine / Hybrid System>1GR-FE EMISSION CONTROL>AIR PUMP>INSPECTION).
OK
NG
Inspect the air pump heater relay (AIR PUMP HTR) (See page Engine / Hybrid System>1GR-FE ENGINE CONTROL>RELAY>ON-VEHICLE INSPECTION).
OK
NG
Remove the air pump heater relay (AIR PUMP HTR).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| air pump heater relay (AIR PUMP HTR) terminal 5 - Body ground | Always | 11 to 14 V |
| *1 | Air Pump Heater Relay (AIR PUMP HTR) |
| *2 | Engine Room Relay Block |
Reinstall the air pump heater relay (AIR PUMP HTR).
OK
NG
Remove the air pump heater relay (AIR PUMP HTR).
Disconnect the air pump connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| air pump heater relay (AIR PUMP HTR) terminal 3 - A50-1 (APH+) | Always | Below 1 Ω |
| A50-3 (APHG) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| air pump heater relay (AIR PUMP HTR) terminal 3 or A50-1 (APH+) - Body ground | Always | 10 kΩ or higher |
Reinstall the air pump heater relay (AIR PUMP HTR).
Reconnect the air pump connector.
OK
NG
Start the engine and warm it up.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV1: OPEN, ASV2: OPEN and AIR PUMP: OFF, ASV1: CLOSE, ASV2: CLOSE.
When Manual Mode is selected, the GTS initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.
Start the engine.
Perform the secondary air injection system forced operation while the engine is idling.
Check that the Data List values for the air pump (AIR PUMP), emission control valve (ASV) and pressure in the secondary air injection system passage (PRESSURE) displayed on the GTS are as shown in the table below.
| Tester Operation | Air Pump | Emission Control Valve | PRESSURE* |
|---|---|---|---|
| AIR PUMP: ON, ASV: OPEN | ON | ON | 1 kPa or higher [A] |
| AIR PUMP: OFF, ASV: CLOSE | OFF | OFF | Below 3 kPa [B] |
*: Average pumping pressure. The pressure should be 1 kPa or higher when the secondary air injection system operates.
The pressures for [A] and [B] should differ by 1 kPa or more.
Turn the ignition switch off.
This Secondary Air Injection Check only allows technicians to operate the secondary air injection system for a maximum of 5 seconds. Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks. While secondary air injection system operation using the GTS is prohibited, the GTS display indicates the prohibition (WAIT or ERROR). If ERROR is displayed on the GTS during the test, stop the engine for 10 minutes, and then try again.
Performing Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If it is necessary to repeat the check, leave an interval of several minutes between System Check operations to prevent the system from overheating.
When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
Turn the ignition switch off when the Secondary Air Injection Check operation finishes.
OK
NG
Start the engine and warm it up.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (if stored) (See page Engine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).
Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.
Start the engine after the GTS initialization is finished.
Perform the System Check operation by pressing ENTER (Next).
Perform the following to confirm the secondary air injection system pending codes: Press the Exit button.
Check for pending DTCs.
Turn the ignition switch off.
When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
Turn the ignition switch off when the Secondary Air Injection Check operation finishes.
| Result | Proceed to |
|---|---|
| P2445 is output | A |
| No pending DTC is output | B |
A
B
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Air Pump Pressure (Absolute) and Air Pump2 Pressure (Absolute).
Check the pressure displayed on the GTS.
45 to 135 kPa
The GTS displays the air pump pressure as absolute pressure.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for Bank 1) | B |
| NG (for Bank 2) | C |
A
B
C
Check that all the pipes and hoses between the air pump and emission control valve are securely connected.
Inspect the pipes and hoses for blockages and damage.
Secondary air injection system piping has no blockages or damage.
OK
NG
Disconnect the air injection control driver connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A49-1 (E) - Body ground | Always | Below 1 Ω |
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A48-1 (BATT) - Body ground | Always | 11 to 14 V (near battery voltage) |
| *a | Front view of wire harness connector
(to Air Injection Control Driver) |
Reconnect the air injection control driver connectors.
OK
NG
Disconnect the ECM connector.
Disconnect the air injection control driver connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B37-23 (AIRP) - A49-4 (SIP) | Always | Below 1 Ω |
Reconnect the ECM connector.
Reconnect the air injection control driver connector.
OK
NG
Inspect the air pump assembly (See page Engine / Hybrid System>1GR-FE EMISSION CONTROL>AIR PUMP>ON-VEHICLE INSPECTION).
OK
NG
Replace the air pump assembly (See page Engine / Hybrid System>1GR-FE EMISSION CONTROL>AIR PUMP>REMOVAL).
NEXT
Start the engine and warm it up.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (if stored) (See page Engine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).
Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air injection check / Automatic Mode.
Start the engine after the GTS initialization is finished.
Perform the System Check operation by pressing ENTER (Next).
Perform the following to confirm the secondary air injection system pending codes: Press the Exit button.
Check for pending DTCs.
No pending DTC is output.
Turn the ignition switch off.
When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
Turn the ignition switch off when the Secondary Air Injection Check operation finishes.
OK
NG
Disconnect the air injection control driver connector.
Connect terminals DI and SIV of the wire harness connector for the air injection control driver.
| *1 | Air Injection Control Driver |
| *2 | ECM |
| *a | Front view of wire harness connector
(to Air Injection Control Driver) |
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV 1: OPEN, ASV 2: OPEN.
When Manual Mode is selected, the GTS initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.
Start the engine.
Perform the secondary air injection system forced operation while the engine is idling.
Measure the voltage between the SIV and E terminals of the ECM connector when the secondary air injection system is ON and OFF.
Turn the ignition switch off.
Performing Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If it is necessary to repeat the check, leave an interval of several minutes between System Check operations to prevent the system from overheating.
When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
Turn the ignition switch off when the Secondary Air Injection Check operation finishes.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A49-3 (SIV) - A49-1 (E) | AIR PUMP: ON, ASV: OPEN | 0.5 to 2 V |
| A49-3 (SIV) - A49-1 (E) | AIR PUMP: OFF, ASV: CLOSE | 11 to 14 V |
Connect terminals DI and SIP of the wire harness connector for the air injection control driver.
| *1 | Air Injection Control Driver |
| *2 | ECM |
| *a | Front view of wire harness connector
(to Air Injection Control Driver) |
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV 1: OPEN, ASV 2: OPEN.
When Manual Mode is selected, the GTS initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.
Start the engine.
Perform the secondary air injection system forced operation while the engine is idling.
Measure the voltage between the SIP and E terminals of the ECM connector when the secondary air injection system is ON and OFF.
Turn the ignition switch off.
Performing Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If it is necessary to repeat the check, leave an interval of several minutes between System Check operations to prevent the system from overheating.
When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
Turn the ignition switch off when the Secondary Air Injection Check operation finishes.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A49-4 (SIP) - A49-1 (E) | AIR PUMP: ON, ASV: OPEN | 0.5 to 2 V |
| A49-4 (SIP) - A49-1 (E) | AIR PUMP: OFF, ASV: CLOSE | 11 to 14 V |
Reconnect the air injection control driver connector.
OK
NG
Replace the air injection control driver (See page Engine / Hybrid System>1GR-FE EMISSION CONTROL>AIR INJECTION DRIVER>REMOVAL).
NEXT
Start the engine and warm it up.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (if stored) (See page Engine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).
Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air injection check / Automatic Mode.
Start the engine after the GTS initialization is finished.
Perform the System Check operation by pressing ENTER (Next).
Perform the following to confirm the secondary air injection system pending codes: Press the Exit button.
Check for pending DTCs.
No pending DTC is output.
Turn the ignition switch off.
When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
Turn the ignition switch off when the Secondary Air Injection Check operation finishes.
OK
NG