Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM › from 2014.08
RM1440E _51 Engine / Hybrid System _056124 1GR-FE ENGINE CONTROL _0273876 SFI SYSTEM J

1GR-FE ENGINE CONTROL  SFI SYSTEM  VC Output Circuit  


DESCRIPTION

The ECM constantly generates 5 V power source voltage from the battery voltages supplied to the +B, +B2 (BATT) terminal to operate the microprocessor. The ECM also provides this power to the sensors through the VC output circuit.

A256646E05
1.667,0.833 2.604,1.125 0.938,0.292 10 false from EFI Fuse 1.656,1.188 2.656,1.469 1,0.281 10 false from MAIN Fuse 0.26,1.802 2.708,2.417 2.448,0.615 10 false to Throttle Position Sensor, Accelerator Pedal Sensor Assembly, etc. (Sensors which have an IC) 0.229,2.708 2.656,3.271 2.427,0.563 10 false to Engine Coolant Temperature Sensor, Intake Air Temperature Sensor, etc. 4.927,3.083 5.333,3.448 0.406,0.365 10 false ECM 2.948,0.76 3.333,0.906 0.385,0.146 10 false BATT 2.865,1.115 3.49,1.323 0.625,0.208 10 false +B, +B2 3.01,1.99 3.292,2.177 0.281,0.188 10 false VC 4.385,0.854 6.177,1.208 1.792,0.354 10 false 5 V Constant Voltage Circuit 5.365,1.927 6.354,2.281 0.99,0.354 10 false Microprocessor 4.073,2.844 4.219,3.01 0.146,0.167 10 false R

When the VC circuit is short-circuited, the microprocessor in the ECM and sensors that are supplied with power through the VC circuit are deactivated because the power is not supplied from the VC circuit. Under this condition, the system does not start up and the MIL does not illuminate even if the system malfunctions.

HINT:

Under normal conditions, the MIL is illuminated when the ignition switch is turned on. The MIL goes off when the engine is started.


WIRING DIAGRAM

A327954E02
0.354,1.458 0.677,1.604 0.323,0.146 10 false B22 0.344,1.625 2.802,1.802 2.458,0.177 10 false VVT Sensor (for Intake Side of Bank 2) 5.031,0.74 5.229,0.885 0.198,0.146 10 false 12 0.354,3.167 0.677,3.313 0.323,0.146 10 false B24 0.354,3.354 2.927,3.531 2.573,0.177 10 false VVT Sensor (for Exhaust Side of Bank 2) 0.333,4.865 0.656,5.01 0.323,0.146 10 false B53 0.344,5.01 2.583,5.188 2.24,0.177 10 false No. 1 Emission Control Valve Set* 0.375,6.542 0.698,6.688 0.323,0.146 10 false B54 0.385,6.698 2.615,6.875 2.229,0.177 10 false No. 2 Emission Control Valve Set* 0.354,8.281 0.677,8.427 0.323,0.146 10 false B31 0.354,8.448 2.615,8.625 2.26,0.177 10 false Power Steering Oil Pressure Switch 2.99,8.427 5.354,8.802 2.365,0.375 10 false *: w/ Secondary Air Injection System 2.125,3.792 2.24,3.938 0.115,0.146 10 false 2 5,7.5 5.198,7.646 0.198,0.146 10 false 16 5.104,4.073 5.281,4.219 0.177,0.146 10 false 1 5.115,5.781 5.292,5.927 0.177,0.146 10 false 2 5.021,2.75 5.219,2.896 0.198,0.146 10 false 17 5.01,2.417 5.219,2.615 0.208,0.198 10 false 18 5.031,1.052 5.229,1.198 0.198,0.146 10 false 11 5.021,0.427 5.219,0.573 0.198,0.146 10 false 16 2.125,0.729 2.24,0.875 0.115,0.146 10 false 1 2.135,0.385 2.25,0.531 0.115,0.146 10 false 3 2.135,4.427 2.25,4.573 0.115,0.146 10 false 4 2.125,4.115 2.24,4.26 0.115,0.146 10 false 3 2.135,2.76 2.25,2.906 0.115,0.146 10 false 2 2.135,2.406 2.25,2.552 0.115,0.146 10 false 1 2.146,2.094 2.26,2.24 0.115,0.146 10 false 3 2.146,1.052 2.26,1.198 0.115,0.146 10 false 2 1.813,0.5 2.063,0.667 0.25,0.167 10 false VC 5.604,7.573 5.958,7.74 0.354,0.167 10 false PSP 1.854,4.521 2.083,4.688 0.229,0.167 10 false E2 1.813,4.219 2.063,4.375 0.25,0.156 10 false AIP 1.823,3.885 2.063,4.042 0.24,0.156 10 false VC 1.771,2.5 2.083,2.667 0.313,0.167 10 false EX+ 1.75,2.177 2.063,2.344 0.313,0.167 10 false VC2 1.688,0.833 2.073,0.979 0.385,0.146 10 false VVL+ 5.604,0.833 5.979,0.99 0.375,0.156 10 false VV2+ 5.615,1.052 5.969,1.229 0.354,0.177 10 false VV2- 5.583,2.51 5.969,2.677 0.385,0.167 10 false EV2+ 5.594,2.75 5.948,2.906 0.354,0.156 10 false EV2- 1.708,1.125 2.063,1.323 0.354,0.198 10 false VVL- 1.802,2.833 2.104,2.99 0.302,0.156 10 false EX- 5.594,4.198 5.948,4.396 0.354,0.198 10 false AIP 5.594,5.896 5.948,6.052 0.354,0.156 10 false AIP2 5.25,0.49 5.573,0.635 0.323,0.146 10 false B36 5.25,0.833 5.573,0.979 0.323,0.146 10 false B36 5.25,1.135 5.583,1.313 0.333,0.177 10 false B36 5.26,2.5 5.583,2.646 0.323,0.146 10 false B36 5.24,2.833 5.563,2.979 0.323,0.146 10 false B36 5.25,7.594 5.573,7.74 0.323,0.146 10 false B37 5.271,4.188 5.594,4.333 0.323,0.146 10 false F51 5.25,5.885 5.573,6.031 0.323,0.146 10 false F51 5.594,0.417 6,0.563 0.406,0.146 10 false VCV2 6.094,8.531 6.448,8.729 0.354,0.198 10 false ECM 2.125,5.479 2.24,5.625 0.115,0.146 10 false 2 2.135,6.104 2.25,6.25 0.115,0.146 10 false 4 2.135,5.813 2.25,5.958 0.115,0.146 10 false 3 1.781,6.177 2.052,6.344 0.271,0.167 10 false E22 1.729,5.896 2.063,6.052 0.333,0.156 10 false AIP2 1.771,5.573 2.094,5.729 0.323,0.156 10 false VC2 2.135,7.188 2.25,7.333 0.115,0.146 10 false 1 2.135,7.802 2.25,7.948 0.115,0.146 10 false 3 2.135,7.5 2.25,7.646 0.115,0.146 10 false 2 1.833,7.906 2.063,8.073 0.229,0.167 10 false E2 1.74,7.583 2.042,7.74 0.302,0.156 10 false PSP 1.833,7.26 2.073,7.417 0.24,0.156 10 false VC 5.104,4.427 5.281,4.573 0.177,0.146 10 false 7 5.594,4.417 6.052,4.573 0.458,0.156 10 false ETHA 5.25,4.521 5.573,4.667 0.323,0.146 10 false B37

A327955E02
0.302,3.042 0.625,3.188 0.323,0.146 10 false B21 0.292,3.198 2.75,3.375 2.458,0.177 10 false VVT Sensor (for Intake Side of Bank 1) 0.313,4.677 0.635,4.823 0.323,0.146 10 false B23 0.323,4.854 2.896,5.031 2.573,0.177 10 false VVT Sensor (for Exhaust Side of Bank 1) 0.313,6.719 0.635,6.865 0.323,0.146 10 false B13 0.302,6.885 2.552,7.063 2.25,0.177 10 false Throttle Body with Motor Assembly 0.292,9.385 0.615,9.531 0.323,0.146 10 false A3 0.292,9.521 2.615,9.698 2.323,0.177 10 false Accelerator Pedal Sensor Assembly 2.854,9.354 5.177,9.677 2.323,0.323 10 false *: w/ Secondary Air Injection System 2.063,5.313 2.177,5.458 0.115,0.146 10 false 5 4.969,0.938 5.188,1.104 0.219,0.167 10 false 15 5.01,0.302 5.208,0.448 0.198,0.146 10 false 8 2.042,2.302 2.156,2.448 0.115,0.146 10 false 1 2.042,2 2.156,2.146 0.115,0.146 10 false 3 2.063,5.958 2.177,6.104 0.115,0.146 10 false 4 2.052,5.625 2.167,5.771 0.115,0.146 10 false 6 2.063,4.271 2.188,4.427 0.125,0.156 10 false 2 2.063,3.938 2.177,4.083 0.115,0.146 10 false 1 2.052,3.615 2.167,3.76 0.115,0.146 10 false 3 2.052,2.635 2.167,2.781 0.115,0.146 10 false 2 1.75,2.083 2,2.25 0.25,0.167 10 false VC 1.604,6.042 2,6.208 0.396,0.167 10 false VTA2 1.677,5.729 2,5.885 0.323,0.156 10 false VTA 1.75,5.396 1.99,5.552 0.24,0.156 10 false VC 1.719,4.021 2.031,4.188 0.313,0.167 10 false EX+ 1.698,3.719 2.01,3.885 0.313,0.167 10 false VC2 1.583,2.385 1.969,2.531 0.385,0.146 10 false VVR+ 5.51,2.396 5.885,2.552 0.375,0.156 10 false VV1+ 5.51,2.625 5.865,2.802 0.354,0.177 10 false VV1- 5.531,4.01 5.917,4.177 0.385,0.167 10 false EV1+ 5.521,4.26 5.875,4.417 0.354,0.156 10 false EV1- 1.625,2.708 1.979,2.906 0.354,0.198 10 false VVR- 0.323,1.344 0.688,1.49 0.365,0.146 10 false O21 0.333,1.5 1.875,1.677 1.542,0.177 10 false Canister Pump Module* 2.052,0.635 2.167,0.781 0.115,0.146 10 false 7 2.052,0.938 2.167,1.083 0.115,0.146 10 false 6 2.052,0.302 2.167,0.448 0.115,0.146 10 false 8 1.667,1.021 2,1.188 0.333,0.167 10 false VCC 1.583,0.708 2.031,0.854 0.448,0.146 10 false VOUT 1.583,0.385 2.021,0.583 0.438,0.198 10 false SGND 1.729,4.344 2.031,4.5 0.302,0.156 10 false EX- 5.51,5.344 5.917,5.542 0.406,0.198 10 false VCTA 5.51,5.729 5.917,5.885 0.406,0.156 10 false VTA1 5.51,6.063 5.927,6.219 0.417,0.156 10 false VTA2 5.177,1.031 5.5,1.177 0.323,0.146 10 false B36 5.177,0.719 5.5,0.865 0.323,0.146 10 false B37 5.177,0.385 5.5,0.531 0.323,0.146 10 false B37 5.021,2.281 5.177,2.427 0.156,0.146 10 false 9 5.177,2.406 5.5,2.552 0.323,0.146 10 false B36 4.958,2.635 5.156,2.781 0.198,0.146 10 false 10 5.167,2.719 5.49,2.865 0.323,0.146 10 false B36 4.958,3.938 5.156,4.083 0.198,0.146 10 false 13 5.177,4.031 5.5,4.177 0.323,0.146 10 false B36 4.958,4.271 5.156,4.417 0.198,0.146 10 false 14 5.177,4.354 5.5,4.5 0.323,0.146 10 false B36 4.958,5.313 5.156,5.458 0.198,0.146 10 false 13 5.167,5.406 5.49,5.552 0.323,0.146 10 false B38 4.948,5.625 5.146,5.771 0.198,0.146 10 false 15 5.167,5.729 5.49,5.875 0.323,0.146 10 false B38 4.958,5.958 5.156,6.104 0.198,0.146 10 false 16 5.177,6.063 5.5,6.208 0.323,0.146 10 false B38 4.958,6.281 5.156,6.427 0.198,0.146 10 false 14 5.177,6.365 5.5,6.51 0.323,0.146 10 false B38 5.021,7.354 5.167,7.5 0.146,0.146 10 false 4 5.177,7.448 5.5,7.594 0.323,0.146 10 false F50 5.01,7.667 5.177,7.813 0.167,0.146 10 false 2 5.177,7.771 5.5,7.917 0.323,0.146 10 false F50 5.01,7.958 5.177,8.104 0.167,0.146 10 false 6 5.188,8.094 5.51,8.24 0.323,0.146 10 false F50 5.01,8.292 5.156,8.438 0.146,0.146 10 false 5 5.177,8.396 5.5,8.542 0.323,0.146 10 false F50 5.01,8.625 5.156,8.771 0.146,0.146 10 false 3 5.188,8.729 5.51,8.875 0.323,0.146 10 false F50 4.99,8.938 5.135,9.083 0.146,0.146 10 false 1 5.177,9.052 5.5,9.198 0.323,0.146 10 false F50 5.51,0.938 5.917,1.083 0.406,0.146 10 false VCV1 5,0.615 5.177,0.76 0.177,0.146 10 false 1 5.51,0.708 5.958,0.854 0.448,0.146 10 false PPMP 5.5,0.292 5.969,0.458 0.469,0.167 10 false ETHW 6.021,9.531 6.375,9.729 0.354,0.198 10 false ECM 2.052,7.354 2.167,7.5 0.115,0.146 10 false 4 2.063,8 2.177,8.146 0.115,0.146 10 false 6 2.052,7.698 2.167,7.844 0.115,0.146 10 false 1 1.656,8.083 1.979,8.25 0.323,0.167 10 false VPA 1.594,7.771 1.99,7.927 0.396,0.156 10 false VCP2 1.573,7.448 1.969,7.604 0.396,0.156 10 false VCPA 2.063,8.313 2.177,8.458 0.115,0.146 10 false 3 2.063,8.948 2.177,9.094 0.115,0.146 10 false 2 2.063,8.635 2.177,8.781 0.115,0.146 10 false 5 1.583,9.042 1.979,9.208 0.396,0.167 10 false EPA2 1.667,8.74 1.969,8.896 0.302,0.156 10 false EPA 1.594,8.406 1.99,8.563 0.396,0.156 10 false VPA2 5.521,6.281 5.854,6.438 0.333,0.156 10 false ETA 2.063,6.271 2.177,6.417 0.115,0.146 10 false 3 1.75,6.354 1.979,6.521 0.229,0.167 10 false E2 5.531,8.083 5.854,8.25 0.323,0.167 10 false VPA 5.531,7.688 5.927,7.844 0.396,0.156 10 false VCP2 5.521,7.354 5.917,7.51 0.396,0.156 10 false VCPA 5.531,8.938 5.927,9.104 0.396,0.167 10 false EPA2 5.531,8.646 5.833,8.802 0.302,0.156 10 false EPA 5.521,8.375 5.917,8.531 0.396,0.156 10 false VPA2

PROCEDURE

1.CHECK MIL
a.

Check that the Malfunction Indicator Lamp (MIL) lights up when the ignition switch is turned to ON.

OK:

MIL lights up.



Result
Result Proceed to
NG A
OK B


A

2.CHECK COMMUNICATION BETWEEN GTS

B

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

2.CHECK COMMUNICATION BETWEEN GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Check the communication between the GTS and ECM.

Result
Result Proceed to
Communication is not possible A
Communication is possible B



A

3.CHECK MIL (THROTTLE BODY WITH MOTOR ASSEMBLY)

B

3.CHECK MIL (THROTTLE BODY WITH MOTOR ASSEMBLY)
a.

Disconnect the throttle body with motor assembly connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result
Result Proceed to
MIL does not illuminate A
MIL illuminates B



A

4.CHECK MIL (ACCELERATOR PEDAL SENSOR ASSEMBLY)

B

REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY

4.CHECK MIL (ACCELERATOR PEDAL SENSOR ASSEMBLY)
a.

Disconnect the accelerator pedal sensor assembly connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result
Result Proceed to
MIL does not illuminate A
MIL illuminates B



A

5.CHECK MIL (VVT SENSOR FOR INTAKE SIDE OF BANK 1)

B

REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY

5.CHECK MIL (VVT SENSOR FOR INTAKE SIDE OF BANK 1)
a.

Disconnect the VVT sensor (for intake side of bank 1) connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result
Result Proceed to
MIL does not illuminate A
MIL illuminates B



A

6.CHECK MIL (VVT SENSOR FOR INTAKE SIDE OF BANK 2)

B

REPLACE VVT SENSOR (FOR INTAKE SIDE OF BANK 1)

6.CHECK MIL (VVT SENSOR FOR INTAKE SIDE OF BANK 2)
a.

Disconnect the VVT sensor (for intake side of bank 2) connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result
Result Proceed to
MIL does not illuminate A
MIL illuminates B



A

7.CHECK MIL (VVT SENSOR FOR EXHAUST SIDE OF BANK 1)

B

REPLACE VVT SENSOR (FOR INTAKE SIDE OF BANK 2)

7.CHECK MIL (VVT SENSOR FOR EXHAUST SIDE OF BANK 1)
a.

Disconnect the VVT sensor (for exhaust side of bank 1) connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result
Result Proceed to
MIL does not illuminate A
MIL illuminates B



A

8.CHECK MIL (VVT SENSOR FOR EXHAUST SIDE OF BANK 2)

B

REPLACE VVT SENSOR (FOR EXHAUST SIDE OF BANK 1)

8.CHECK MIL (VVT SENSOR FOR EXHAUST SIDE OF BANK 2)
a.

Disconnect the VVT sensor (for exhaust side of bank 2) connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result
Result Proceed to
MIL does not illuminate A
MIL illuminates B



A

9.CHECK MIL (POWER STEERING OIL PRESSURE SWITCH)

B

REPLACE VVT SENSOR (FOR EXHAUST SIDE OF BANK 2)

9.CHECK MIL (POWER STEERING OIL PRESSURE SWITCH)
a.

Disconnect the power steering oil pressure switch connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result
Result Proceed to
MIL does not illuminate (w/ Secondary Air Injection System) A
MIL does not illuminate (w/o Secondary Air Injection System) B
MIL illuminates C



A

10.CHECK MIL (NO. 1 EMISSION CONTROL VALVE SET)

B

13.CHECK HARNESS AND CONNECTOR

C

10.CHECK MIL (NO. 1 EMISSION CONTROL VALVE SET)
a.

Disconnect the No. 1 emission control valve set connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result
Result Proceed to
MIL does not illuminate A
MIL illuminates B



A

11.CHECK MIL (NO. 2 EMISSION CONTROL VALVE SET)

B

11.CHECK MIL (NO. 2 EMISSION CONTROL VALVE SET)
a.

Disconnect the No. 2 emission control valve set connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result
Result Proceed to
MIL does not illuminate A
MIL illuminates B



A

12.CHECK MIL (CANISTER PUMP MODULE)

B

12.CHECK MIL (CANISTER PUMP MODULE)
a.
A225195

Disconnect the canister pump module connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result
Result Proceed to
MIL does not illuminate A
MIL illuminates B



A

13.CHECK HARNESS AND CONNECTOR

B

13.CHECK HARNESS AND CONNECTOR
a.

Disconnect the throttle body with motor assembly connector.


b.

Disconnect the accelerator pedal sensor assembly connector.


c.

Disconnect the VVT sensor (for intake side of bank 1) connector.


d.

Disconnect the VVT sensor (for intake side of bank 2) connector.


e.

Disconnect the VVT sensor (for exhaust side of bank 1) connector.


f.

Disconnect the VVT sensor (for exhaust side of bank 2) connector.


g.

Disconnect the power steering oil pressure switch connector.


h.

Disconnect the No. 1 emission control valve set connector*.


i.

Disconnect the No. 2 emission control valve set connector*.


j.

Disconnect the canister pump module connector*.


k.

Disconnect the ECM connectors.


l.

Measure the resistance according to the value(s) in the table below.

*: w/ Secondary Air Injection System

Standard Resistance:
Tester Connection Condition Specified Condition
B38-13 (VCTA) - Body ground Always 10 kΩ or higher
F50-4 (VCPA) - Body ground Always 10 kΩ or higher
F50-2 (VCP2) - Body ground Always 10 kΩ or higher
B36-15 (VCV1) - Body ground Always 10 kΩ or higher
B36-16 (VCV2) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR