Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM
RM1440E _51 Engine / Hybrid System _056124 1GR-FE ENGINE CONTROL _0273876 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0365  Camshaft Position Sensor "B" Circuit (Bank 1)  P0367  Camshaft Position Sensor "B" Circuit Low Input (Bank 1)  P0368  Camshaft Position Sensor "B" Circuit High Input (Bank 1)  P0390  Camshaft Position Sensor "B" Circuit (Bank 2)  P0392  Camshaft Position Sensor "B" Circuit Low Input (Bank 2)  P0393  Camshaft Position Sensor "B" Circuit High Input (Bank 2)  


DESCRIPTION

The exhaust camshaft's Variable Valve Timing (VVT) sensor (EV1, EV2 signal) consists of a magnet and MRE (Magnetoresistive Element).

The exhaust camshaft has a sensor plate with 3 teeth on its outer circumference.

When the exhaust camshaft rotates, changes occur in the air gaps between the 3 teeth and MRE, which affects the magnetic field. As a result, the resistance of the MRE material fluctuates. The VVT sensor converts the exhaust camshaft rotation data to pulse signals, uses the pulse signals to determine the camshaft angle, and sends the camshaft angle data to the ECM.

DTC No. DTC Detection Condition Trouble Area
P0365
P0390
There is no VVT sensor signal despite the crankshaft position sensor input being normal at an engine speed of 600 rpm or more (1 trip detection logic).
·

Open or short in VVT sensor for exhaust camshaft circuit

·

VVT sensor for exhaust camshaft

·

Exhaust camshaft

·

Timing chain has jumped tooth

·

ECM


P0367
P0392
Output voltage of the VVT sensor is below 0.3 V for 4 seconds (1 trip detection logic).
·

Open or short in VVT sensor for exhaust camshaft circuit

·

VVT sensor for exhaust camshaft

·

Exhaust camshaft

·

Timing chain has jumped tooth

·

ECM


P0368
P0393
Output voltage of the VVT sensor is higher than 4.7 V for 4 seconds (1 trip detection logic).
·

Open or short in VVT sensor for exhaust camshaft circuit

·

VVT sensor for exhaust camshaft

·

Exhaust camshaft

·

Timing chain has jumped tooth

·

ECM



A228079E04
1.063,2.833 2.042,3.031 0.979,0.198 10 false 20 msec./DIV. 0.083,0.813 0.646,0.979 0.563,0.167 10 false 5 V/DIV. 0.198,1.573 0.479,1.771 0.281,0.198 10 false NE 0.115,2.073 0.479,2.271 0.365,0.198 10 false EV1 3.052,1.552 3.385,1.75 0.333,0.198 10 false GND 3.042,2.167 3.375,2.365 0.333,0.198 10 false GND 3.052,2.563 3.385,2.76 0.333,0.198 10 false GND 0.115,2.479 0.479,2.677 0.365,0.198 10 false EV2 0.354,0.271 2.76,0.469 2.406,0.198 10 false EV1, EV2 and NE Signal Waveforms

Reference: Inspection using an oscilloscope

HINT:
·

The correct waveforms are as shown.

·

EV1+ and EV2+ are the VVT sensor signal, and NE+ is the crankshaft position sensor signal.

Item Content
Terminal NE+ - NE-
EV1+ - EV1-
EV2+ - EV2-
Equipment Setting 5 V/DIV.
20 msec./DIV.
Condition Cranking or idling




MONITOR DESCRIPTION

If no signal is transmitted by the VVT sensor despite the camshaft revolving, or the rotations of the camshaft and crankshaft are not synchronized, the ECM interprets this as a malfunction of the sensor.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE

1.CHECK TERMINAL VOLTAGE (SENSOR POWER SOURCE)
a.
U180632E01
0.436,0.969 0.703,1.131 0.267,0.163 10 B23 0.436,1.321 0.703,1.484 0.267,0.163 10 B24 2.317,1.684 2.774,1.847 0.457,0.163 10 VC2 0.079,0.042 0.269,0.205 0.190,0.163 10 *a 1.96,1.346 2.274,1.674 false

Disconnect the VVT sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B23-3 (VC2) - Body ground Ignition switch ON 4.5 to 5.0 V
B24-3 (VC2) - Body ground Ignition switch ON 4.5 to 5.0 V


Text in Illustration
*a Front view of wire harness connector
(to VVT Sensor)


d.

Reconnect the VVT sensor connector.



OK

2.CHECK HARNESS AND CONNECTOR (VVT SENSOR - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (VVT SENSOR - ECM)
a.

Disconnect the VVT sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
B23-1 (EX+) - B36-13 (EV1+) Always Below 1 Ω
B23-2 (EX-) - B36-14 (EV1-) Always Below 1 Ω
B24-1 (EX+) - B36-18 (EV2+) Always Below 1 Ω
B24-2 (EX-) - B36-17 (EV2-) Always Below 1 Ω
B23-1 (EX+) or B36-13 (EV1+) - Body ground Always 10 kΩ or higher
B23-2 (EX-) or B36-14 (EV1-) - Body ground Always 10 kΩ or higher
B24-1 (EX+) or B36-18 (EV2+) - Body ground Always 10 kΩ or higher
B24-2 (EX-) or B36-17 (EV2-) - Body ground Always 10 kΩ or higher



d.

Reconnect the VVT sensor connector.


e.

Reconnect the ECM connector.



OK

3.CHECK SENSOR INSTALLATION (VVT SENSOR FOR EXHAUST CAMSHAFT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK SENSOR INSTALLATION (VVT SENSOR FOR EXHAUST CAMSHAFT)
a.
A388055E03
1.281,1.385 2.042,1.583 0.76,0.198 10 false Clearance 0.354,1.646 1.01,1.896 0.656,0.25 10 false Normal 2.469,1.781 3.167,1.99 0.698,0.208 10 false Abnormal

Check the VVT sensor installation.

OK:

Sensor is installed correctly.




OK

4.CHECK EXHAUST CAMSHAFT

NG

4.CHECK EXHAUST CAMSHAFT
a.

Check the teeth of the camshaft.


OK:

Teeth do not have any cracks or deformation.



OK

5.REPLACE VVT SENSOR

NG

5.REPLACE VVT SENSOR

NEXT

6.CHECK WHETHER DTC OUTPUT RECURS
6.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.



e.

Start the engine.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Code.


g.

Read DTCs.

Result
Display (DTC Output) Proceed to
No output A
P0365, P0367, P0368, P0390, P0392 or P0393 B

HINT:

If the engine does not start, replace the ECM.




A

END

B