1.INSTALL STUD BOLT
Install the oil pan stud bolt.
Using E6 and E8 "TORX" socket wrenches, install the 6 stud bolts as shown in the illustration.
| *a | 73 mm (2.87 in) |
| *b | 20 mm (0.787 in.) |
| *c | 13 mm (0.512 in.) |
| *d | 27 mm (1.06 in.) |
| *e | 16 mm (0.630 in.) |
| *f | 9 mm (0.354 in.) |
| *g | 19 mm (0.748 in.) |
| *h | 9 mm (0.354 in.) |
| *i | 9 mm (0.354 in.) |
Install the cylinder head cover LH stud bolt.
Using an E6 "TORX" socket wrench, install the stud bolt as shown in the illustration.
| *a | 34 mm (1.34 in.) |
| *b | 21 mm (0.827 in.) |
| *c | 9 mm (0.354 in.) |
2.INSTALL RING PIN
Using a plastic-faced hammer, tap in new ring pins to the camshaft housing.
2.7 to 3.3 mm (0.106 to 0.130 in.)
| *A | LH | *B | RH |
| *1 | Protrusion Height | - | - |
3.INSTALL STRAIGHT PIN
Using a plastic-faced hammer, tap in new straight pins to the camshaft housing.
| Item | Specified Condition |
|---|---|
| Ring pin A | 7.7 to 8.3 mm (0.303 to 0.327 in.) |
| Ring pin B | 5.7 to 6.3 mm (0.224 to 0.248 in.) |
| *A | LH | *B | RH |
| *1 | Protrusion Height | - | - |
11432A
4.INSTALL NO. 1 TAPER SCREW PLUG
Apply adhesive to 2 or 3 threads of the No. 1 taper screw plug end.
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
Install the No. 1 taper screw plug.
| *a | LH side |
Install the No. 1 taper screw plug within 3 minutes after applying adhesive.
Do not expose the No. 1 taper screw plug to coolant within 1 hour of the installation.
11381A
5.INSTALL REAR CRANKSHAFT OIL SEAL
Using SST and a hammer, tap in a new oil seal until its surface is flush with the rear oil seal retainer edge.
Apply MP grease to the lip of the oil seal.
11381
6.INSTALL ENGINE REAR OIL SEAL RETAINER
Remove any old packing (FIPG) material and be careful not to drop any oil on the contact surfaces of the oil seal retainer or cylinder block.
Apply seal packing in a continuous line as shown in the illustration.
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
| *1 | Seal Packing |
Remove any oil from the contact surfaces.
Install the oil seal retainer within 3 minutes after applying seal packing.
2 to 3 mm (0.0787 to 0.118 in.)
Install the oil seal retainer with the 5 bolts and 2 nuts.
When installing the oil seal retainer, make sure the lip of the oil seal is not damaged.
When installing the oil seal retainer, make sure the lip of the oil seal is not folded incorrectly.
Do not start the engine for at least 2 hours after installation.
7.INSTALL CYLINDER BLOCK WATER JACKET SPACER
Install the 2 water jacket spacers as shown in the illustration.
| *1 | UP Mark |
| *2 | L Mark |
| *3 | R Mark |
Make sure that face the "L mark", "R mark" and "UP mark" are oriented as shown in the illustration.
8.INSTALL KNOCK SENSOR
16332
9.INSTALL NO. 1 WATER OUTLET PIPE
11115
10.INSTALL CYLINDER HEAD GASKET
11101
11.INSTALL CYLINDER HEAD SUB-ASSEMBLY
11116
12.INSTALL NO. 2 CYLINDER HEAD GASKET
11102
13.INSTALL CYLINDER HEAD LH
13716
14.INSTALL VALVE STEM CAP
Apply a light coat of engine oil to the valve stem caps.
Install the 24 valve stem caps to the cylinder head.
13750
15.INSTALL VALVE LASH ADJUSTER ASSEMBLY
Inspect the valve lash adjuster (See page Engine / Hybrid System>1GR-FE ENGINE MECHANICAL>ENGINE UNIT>INSPECTION).
Install the 24 valve lash adjusters to the cylinder head.
Install the lash adjuster at the same place it was removed from.
13801
16.INSTALL NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY
Apply engine oil to the lash adjuster tips and valve stem cap ends.
Install the 24 valve rocker arms as shown in the illustration.
| *1 | Valve Rocker Arm |
| *2 | Lash Adjuster |
| *3 | Valve Stem |
| *4 | Valve Stem Cap |
17.INSTALL CAMSHAFT BEARING CAP (for Bank 2)
Apply a light coat of engine oil to the camshaft journals, camshaft housings and bearing caps.
Install the No. 3 camshaft and No. 4 camshaft to the camshaft housing.
Check the marks and numbers on the camshaft bearing caps and place each of them in the proper position facing the proper direction.
Temporarily install the 8 bolts in the order shown in the illustration.
11104A
18.INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY LH
Make sure that the valve rocker arm is installed as shown in the illustration.
| *1 | Valve Rocker Arm |
| *2 | Lash Adjuster |
| *3 | Valve Stem |
| *4 | Valve Stem Cap |
Apply seal packing in a continuous line as shown in the illustration.
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
3.5 to 4.5 mm (0.138 to 0.177 in.)
| *1 | Seal Packing |
Remove any oil from the contact surface.
Install the camshaft housing within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.
Install the camshaft housing sub-assembly LH and tighten the 13 bolts in the order shown in the illustration.
| *1 | Knock Pin |
| *a | Front View |
When installing the camshaft housing sub-assembly LH, it is necessary to correctly position the camshafts as shown in the illustration. Failure to correctly position these parts may result in damage due to contact between the pistons and valves. If a camshaft is rotated with a piston at TDC, valve contact will occur.
If any of the bolts are loosened during installation, remove the camshaft housing sub-assembly LH, clean the installation surfaces and reapply seal packing.
If the camshaft housing sub-assembly LH is removed because any of the bolts are loosened during installation, make sure that the previously applied seal packing does not enter any oil passages.
Do not start the engine for at least 2 hours after installing.
Tighten the 8 bolts in the order shown in the illustration.
Thoroughly wipe clean any seal packing.
19.INSTALL CAMSHAFT BEARING CAP (for Bank 1)
Apply a light coat of engine oil to the camshaft journals, camshaft housings and bearing caps.
Install the camshaft and No. 2 camshaft to the camshaft housing.
Check the marks and numbers on the camshaft bearing caps and place each of them in the proper position facing the proper direction.
Temporarily install the 8 bearing cap bolts in the order shown in the illustration.
11103C
20.INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY RH
Make sure that the No. 1 valve rocker arm sub-assembly is installed as shown in the illustration.
| *1 | Valve Rocker Arm |
| *2 | Lash Adjuster |
| *3 | Valve Stem |
| *4 | Valve Stem Cap |
Apply seal packing in a continuous line as shown in the illustration.
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
3.5 to 4.5 mm (0.138 to 0.177 in.)
| *1 | Seal Packing |
Remove any oil from the contact surface.
Install the camshaft housing within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.
Install the camshaft housing sub-assembly RH and tighten the 12 bolts in the order shown in the illustration.
| *1 | Knock Pin |
| *a | Front View |
When installing the camshaft housing RH, it is necessary to correctly position the camshafts as shown in the illustration.
Failure to correctly position these parts may result in damage due to contact between the pistons and valves. If a camshaft is rotated with a piston at TDC, valve contact will occur.
If any of the bolts are loosened during installation, remove the camshaft housing sub-assembly RH, clean the installation surfaces and reapply seal packing.
If the camshaft housing sub-assembly RH is removed because any of the bolts are loosened during installation, make sure that the previously applied seal packing does not enter any oil passages.
Do not start the engine for at least 2 hours after installing.
Tighten the 8 bolts in the order shown in the illustration.
Thoroughly wipe clean any seal packing.
13560A
21.INSTALL NO. 3 CHAIN TENSIONER ASSEMBLY (for Bank 2)
Install the No. 3 chain tensioner assembly with the bolt.
Push in the tensioner and insert a pin with a diameter of 1.0 mm (0.0394 in.) into the hole to hold the tensioner.
| *1 | Pin |
| *2 | Plunger |
| *a | Push |
22.INSTALL CAMSHAFT TIMING GEARS AND NO. 2 CHAIN (for Bank 2)
Align the mark plates (yellow) with the timing marks of the camshaft timing gear assemblies as shown in the illustration.
| *1 | Timing Mark |
| *2 | Mark Plate |
Apply a light coat of engine oil to the bolt threads and bolt-seating surface.
Align the knock pin of the camshaft with the pin hole of the camshaft timing gear assembly. Install the camshaft timing gear assembly and camshaft timing exhaust gear LH with the No. 2 chain sub-assembly installed.
Using SST to hold the hexagonal portion of each camshaft, tighten the bolts of the camshaft timing gear assembly and camshaft timing exhaust gear assembly.
| *a | Turn |
| *b | Hold |
Remove the pin from the No. 3 chain tensioner assembly.
13550
23.INSTALL NO. 2 CHAIN TENSIONER ASSEMBLY (for Bank 1)
Install the No. 2 chain tensioner assembly with the bolt.
Push in the No. 2 chain tensioner assembly and insert a pin with a diameter of 1.0 mm (0.0394 in.) into the hole to hold the tensioner.
| *1 | Pin |
| *2 | Plunger |
| *a | Push |
24.INSTALL CAMSHAFT TIMING GEARS AND NO. 2 CHAIN (for Bank 1)
Align the mark plates (yellow) with the timing marks of the camshaft timing gear assemblies as shown in the illustration.
| *1 | Timing Mark |
| *2 | Mark Plate |
Apply a light coat of engine oil to the bolt threads and bolt-seating surface.
Align the knock pin of the camshaft with the pin hole of the camshaft timing gear assembly. Install the camshaft timing gear assembly and camshaft timing exhaust gear assembly with the No. 2 chain sub-assembly installed.
Using SST to hold the hexagonal portion of each camshaft, tighten the bolts of the camshaft timing gear assembly and camshaft timing exhaust gear assembly.
| *a | Turn |
| *b | Hold |
Remove the pin from the No. 2 chain tensioner assembly.
13561
25.INSTALL NO. 1 CHAIN VIBRATION DAMPER
Install the No. 1 chain vibration damper with the 2 bolts.
13562
26.INSTALL NO. 2 CHAIN VIBRATION DAMPER
Install the 2 No. 2 chain vibration dampers.
13521
27.INSTALL CRANKSHAFT TIMING SPROCKET
Align the key groove of the timing sprocket with the timing sprocket set key.
Install the timing sprocket to the crankshaft with the sprocket facing inward as shown in the illustration.
| *a | Inward |
13581
28.INSTALL NO. 1 IDLE GEAR SHAFT
Apply a light coat of engine oil to the sliding surface of the No. 1 idle gear shaft.
Temporarily install the No. 1 idle gear shaft and No. 1 idle gear with the No. 2 idle gear shaft while aligning the knock pin of the No. 1 idle gear shaft with the knock pin groove of the cylinder block.
| *1 | Knock Pin |
Make sure that the idle gear is installed facing the proper direction.
Using a 10 mm hexagon wrench, tighten the No. 2 idle gear shaft.
Remove the bar from the chain tensioner.
13506
29.INSTALL NO. 1 CHAIN SUB-ASSEMBLY
Align the mark plate and timing marks as shown in the illustration and install the chain.
| *1 | Mark Plate |
| *2 | Timing Mark |
The camshaft mark plates are orange.
Do not pass the chain around the crankshaft, just temporarily place it on the crankshaft.
Turn the camshaft timing gear assembly on bank 1 counterclockwise to tighten the chain between the banks.
| *1 | Chain Plate |
| *a | When idle sprocket is reused |
| *b | Mark |
| *c | Align |
|
Turn |
When the idle sprocket assembly is reused, align the chain plate with the mark where the plate had been when tightening the chain between the banks.
Align the mark plate and timing marks as shown in the illustration and install the chain to the crankshaft timing sprocket.
| *1 | Mark Plate |
| *2 | Timing Mark |
The crankshaft mark plate is yellow.
Temporarily install the pulley set bolt.
Turn the crankshaft clockwise to set it to the RH block bore center line (TDC/compression).
| *1 | Center Line |
| *2 | Timing Mark |
| *3 | Sensor Plate |
13559
30.INSTALL CHAIN TENSIONER SLIPPER
Install the chain tensioner slipper.
13540
31.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY
Turn the stopper plate of the tensioner clockwise and push in the plunger of the tensioner as shown in the illustration.
| *1 | Stopper Plate |
| *a | Push |
Turn the stopper plate of the tensioner counterclockwise and insert a pin of φ1.27 mm (0.0500 in.) into the holes on the stopper plate and tensioner to fix the stopper plate in place.
Install the chain tensioner with the 2 bolts.
Remove the pin from the No. 1 chain tensioner.
32.INSPECT VALVE TIMING
Check the camshaft timing marks.
Check each timing mark from a viewpoint directly in line with the center of the camshaft and the timing mark on each camshaft timing gear.
If the timing marks are checked from any other viewpoint, the valve timing may appear misaligned.
Check that each camshaft timing mark is positioned as shown in the illustration.
| *1 | Timing Mark | - | - |
| *a | Viewpoint | - | - |
for Intake Camshaft:
Be sure to check mark A at the point when marks B, C and D are positioned in line. If the marks are checked from any other viewpoint, they cannot be checked correctly.
If the valve timing is misaligned, reinstall the timing chain.
Remove the pulley set bolt.
11301C
33.INSTALL FRONT CRANKSHAFT OIL SEAL
16100
34.INSTALL WATER PUMP ASSEMBLY
Install a new gasket and the water pump with the 8 bolts.
11302
35.INSTALL TIMING CHAIN COVER SUB-ASSEMBLY
12121
36.INSTALL NO. 1 OIL PAN BAFFLE PLATE
Install the No. 1 oil pan baffle plate with the 6 bolts.
12101
37.INSTALL OIL PAN SUB-ASSEMBLY
15104
38.INSTALL OIL STRAINER SUB-ASSEMBLY
12102A
39.INSTALL NO. 2 OIL PAN SUB-ASSEMBLY
12101A
40.INSTALL OIL PAN DRAIN PLUG
Install a new gasket and the drain plug.
41.POUR ENGINE OIL
Before installing the cylinder head cover, pour engine oil into the locations shown in the illustration.
11193
42.INSTALL SPARK PLUG TUBE GASKET
Using a cutter knife, cut off the seal part of the removed gasket.
|
Area to cut off |
Using the removed gasket and a hammer, tap in a new gasket until it stops.
| *1 | Removed Gasket |
| *2 | New Gasket |
If the removed gasket does not fit on the new one, correct the removed one with pliers.
Apply a light coat of MP grease to the gasket lip.
Return the ventilation baffle plate claws to their original positions.
11201
43.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY
Remove any old packing (FIPG) material and be careful not to drop any oil on the contact surfaces of the cylinder head, timing chain cover or cylinder head cover.
Apply seal packing as shown in the illustration.
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
2 to 3 mm (0.0787 to 0.118 in.)
|
Seal Packing |
Remove any oil from the contact surface.
Install the cylinder head cover within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.
Install 3 new gaskets as shown in the illustration.
Install a new gasket to the cylinder head cover.
Install the seal washers to the bolts.
Temporarily install the cylinder head cover with the 12 bolts. Tighten the bolts uniformly in several steps.
| Item | Length |
|---|---|
| A | 25 mm (0.984 in.) |
| B | 35 mm (1.38 in.) |
| C | 65 mm (2.56 in.) |
| D | 60 mm (2.36 in.) |
|
Bolt A |
|
Bolt B |
|
Bolt C |
|
Bolt D |
Do not start the engine for at least 2 hours after the installation.
11202
44.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY LH
Remove any old packing (FIPG) material and be careful not to drop any oil on the contact surfaces of the cylinder head, timing chain cover or cylinder head cover.
Apply seal packing as shown in the illustration.
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
2 to 3 mm (0.0787 to 0.118 in.)
|
Seal Packing |
Remove any oil from the contact surface.
Install the cylinder head cover within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.
Install 3 new gaskets as shown in the illustration.
Install a new gasket to the cylinder head cover.
Install the seal washers to the bolts.
Temporarily install the cylinder head cover with the 12 bolts. Tighten the bolts uniformly in several steps.
| Item | Length |
|---|---|
| A | 25 mm (0.984 in.) |
| B | 35 mm (1.38 in.) |
| C | 70 mm (2.76 in.) |
| D | 60 mm (2.36 in.) |
|
Bolt A |
|
Bolt B |
|
Bolt C |
|
Bolt D |
Do not start the engine for at least 2 hours after the installation.
13471
45.INSTALL CRANKSHAFT PULLEY
12204
46.INSTALL PCV VALVE SUB-ASSEMBLY
Apply adhesive to 2 or 3 threads of the PCV valve.
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
Install the PCV valve.
Install the PCV valve hose.
19100P
47.INSTALL SPARK PLUG
16356
48.INSTALL REAR WATER BY-PASS JOINT
Apply soapy water to a new O-ring and install it to the No. 1 water outlet pipe. Then install 2 new gaskets to the water ports LH and RH.
| *1 | New O-Ring |
| *2 | New Gasket |
Install the rear water by-pass joint with the 2 bolts and 4 nuts.
16323
49.INSTALL WATER INLET HOUSING
15671
50.INSTALL OIL FILTER BRACKET
51.INSTALL OIL FILTER ELEMENT
15772
52.INSTALL NO. 2 OIL PIPE
15771
53.INSTALL NO. 1 OIL PIPE
12185
54.INSTALL OIL FILLER CAP HOUSING
Install a new gasket and the oil filler cap housing with the 2 nuts.
| *1 | New Gasket |
Install the oil filler cap.
15330B
55.INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
RH:
Apply a light coat of engine oil to 2 new O-rings.
Install the 2 O-rings to the 2 oil control valves.
Install the 2 oil control valves with the 2 bolts.
Be careful that the O-ring is not cracked when installing the camshaft timing oil control valve.
LH:
Apply a light coat of engine oil to 2 new O-rings.
Install the 2 O-rings to the 2 oil control valves.
Install the 2 oil control valves with the 2 bolts.
Be careful that the O-ring is not cracked when installing the camshaft timing oil control valve.
56.INSTALL CRANKSHAFT POSITION SENSOR
Install the sensor with the bolt.
57.INSTALL VVT SENSOR
RH:
Install the 2 VVT sensors with the 2 bolts.
LH:
Install the 2 VVT sensors with the 2 bolts.
11415
58.INSTALL CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY
Apply adhesive to 2 or 3 threads of the water drain cock end.
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
Install the water drain cock sub-assembly.
| *a | RH side |
| *b | Front |
Install the drain cock sub-assembly within 3 minutes after applying adhesive.
Do not expose the water drain cock sub-assembly to coolant within 1 hour of the installation.
Rotate the water drain cock sub-assembly clockwise to the position shown in the illustration.
Do not rotate the water drain cock sub-assembly by more than 1 revolution (360°) after tightening the water drain cock sub-assembly to the specified torque.
Do not loosen the water drain cock sub-assembly after setting it correctly.
Install the water drain cock plug to the water drain cock.
89422
59.INSTALL ENGINE COOLANT TEMPERATURE SENSOR
Install a new gasket to the sensor.
Using a 19 mm deep socket wrench, install the sensor.
83530
60.INSTALL ENGINE OIL PRESSURE SWITCH ASSEMBLY
Using a 24 mm deep socket wrench, install the oil pressure switch.