Home › Engine / Hybrid System › 1GR-FE COOLING › RADIATOR › 2009.08–2013.08
RM1440E _51 Engine / Hybrid System _056129 1GR-FE COOLING _0273913 RADIATOR A

1GR-FE COOLING  RADIATOR  INSTALLATION  


PROCEDURE

Hide 16561 1.INSTALL NO. 1 RADIATOR TO SUPPORT SEAL

a.
A225191

Install the seal to the radiator assembly as shown in the illustration.


Hide 16562 2.INSTALL NO. 2 RADIATOR TO SUPPORT SEAL

a.
A225190

Install the seal to the radiator assembly as shown in the illustration.


Hide 16400 3.INSTALL RADIATOR ASSEMBLY

a.
A224958

Insert the radiator bracket hooks into the radiator support holes.


b.

Install the radiator with the 4 bolts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


c.
A224976E01
1.222,0.143 1.392,0.289 0.170,0.145 10 *a

Connect the 2 oil cooler hoses.

Text in Illustration
*a Upper

HINT:

Make sure the direction of the hose clamp is as shown in the illustration.



Hide 16711 4.INSTALL FAN SHROUD

a.

Install the fan pulley to the water pump.


b.

Place the shroud together with the coupling fan between the radiator and engine.

NOTICE:

Be careful not to damage the radiator core.



c.
A229548E06
2.417,0.854 2.583,0.854 2.583,0.854 2.594,1.677 true 2.406,1.104 2.583,1.104 true 0.656,0.99 0.802,1.135 0.146,0.146 10 false *1 2.521,1.708 2.667,1.854 0.146,0.146 10 false *1

Align the paint marks on the heads of the water pump stud bolts with the paint marks of the same color on the outer edge of the fluid coupling flange and install the fluid coupling to the water pump.

Text in Illustration
*1 Paint Mark


d.

Temporarily install the fluid coupling fan to the water pump with the 4 nuts. Tighten the nuts as much as possible by hand.


e.
A223087

Attach the claws of the shroud to the radiator as shown in the illustration.


f.

Install the shroud with the 2 bolts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


g.

Install the fan and generator V-belt (See page Engine / Hybrid System>1GR-FE ENGINE MECHANICAL>DRIVE BELT>INSTALLATION).


h.

Tighten the 4 nuts of the fluid coupling fan.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 32907C 5.CONNECT OIL COOLER TUBE

a.
A226789

Connect the oil cooler tube with the 2 bolts, and attach the claw to close the flexible hose clamp.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 16470 6.INSTALL RADIATOR RESERVOIR

a.

Install the radiator reservoir with the 3 bolts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


b.

Connect the reservoir hose to upper side of the radiator tank upper.


Hide 16572D 7.INSTALL NO. 2 RADIATOR HOSE

a.
A227084E05
2.958,1.708 2.594,1.708 true 2.958,1.271 2.875,1.271 2.875,1.271 2.563,1.385 true 2.177,0.375 2.281,0.375 2.281,0.375 2.531,0.729 true 2.583,0.146 2.75,0.313 0.167,0.167 10 false *a 1.99,0.302 2.156,0.469 0.167,0.167 10 false *1 3.01,1.219 3.177,1.385 0.167,0.167 10 false *1 3,1.625 3.167,1.792 0.167,0.167 10 false *2 2.042,0.948 2.292,1.094 0.25,0.146 10 false 90°

Connect the No. 2 radiator hose so that its paint mark aligns with the radiator protrusion as shown in the illustration.

Text in Illustration
*1 Paint Mark
*2 Protrusion
*a Upper

HINT:

Make sure the direction of the hose clamp is as shown in the illustration.



b.
A227083E09
2.938,1.646 2.615,1.646 false 2.917,1.208 2.833,1.208 2.833,1.208 2.563,1.333 true 2.333,0.177 2.438,0.177 2.438,0.177 2.698,0.417 true 3.042,0.51 2.969,0.51 2.969,0.51 2.865,0.604 true 2.896,0.104 3.063,0.271 0.167,0.167 10 false *b 1.958,0.708 2.125,0.875 0.167,0.167 10 false *a 3.083,0.438 3.25,0.604 0.167,0.167 10 false *1 2.969,1.146 3.135,1.313 0.167,0.167 10 false *1 2.979,1.573 3.146,1.74 0.167,0.167 10 false *2 2.042,0.479 2.292,0.625 0.25,0.146 10 false 90° 2.104,0.115 2.354,0.26 0.25,0.146 10 false 45°

Connect the No. 2 radiator hose so that its paint mark aligns with the water inlet housing protrusion as shown in the illustration.

Text in Illustration
*1 Paint Mark
*2 Protrusion
*a Front
*b Upper

HINT:

Make sure the direction of the hose clamp is as shown in the illustration.



Hide 16571C 8.INSTALL NO. 1 RADIATOR HOSE

a.
U180675E02
2.865,2.969 2.5,2.969 true 2.823,2.542 2.74,2.542 2.74,2.542 2.448,2.646 true 2.823,2.229 2.74,2.229 2.74,2.229 2.438,1.948 true 1.396,0.198 1.5,0.198 1.5,0.198 1.677,0.458 true 2.208,0.542 2.125,0.542 2.125,0.542 1.833,0.656 true 2.458,1.396 2.625,1.563 0.167,0.167 10 false *b 1.875,0.125 2.042,0.292 0.167,0.167 10 false *b 0.927,0.75 1.094,0.917 0.167,0.167 10 false *a 2.865,2.156 3.031,2.323 0.167,0.167 10 false *1 2.271,0.458 2.438,0.625 0.167,0.167 10 false *1 2.865,2.469 3.031,2.635 0.167,0.167 10 false *1 2.885,2.885 3.052,3.052 0.167,0.167 10 false *2 2.781,1.625 3.031,1.771 0.25,0.146 10 false 90° 1.073,0.448 1.323,0.594 0.25,0.146 10 false 90° 1.146,0.115 1.396,0.26 0.25,0.146 10 false 45° 0.552,0.156 0.688,0.313 0.135,0.156 10 false A 1.896,1.427 2.031,1.583 0.135,0.156 10 false B

Connect the No. 1 radiator hose to the water inlet housing shown in the illustration labeled A.

Text in Illustration
*1 Paint Mark
*2 Protrusion
*a Front
*b Upper

HINT:
·

Make sure the paint mark of the No. 1 radiator hose is facing upward.

·

Make sure the direction of the hose clamp is as shown in the illustration.




b.

Connect the No. 1 radiator hose so that its paint mark aligns with the radiator protrusion as shown in the illustration labeled B.

HINT:
·

Make sure the paint mark of the No. 1 radiator hose is facing upward.

·

Make sure the direction of the hose clamp is as shown in the illustration.




Hide 53294C 9.INSTALL RADIATOR SIDE DEFLECTOR LH

a.

Attach the 3 claws.


b.

Install the deflector with the clip.


Hide 53293C 10.INSTALL RADIATOR SIDE DEFLECTOR RH

a.

Attach the 3 claws.


b.

Install the deflector with the clip.


Hide 52521 11.INSTALL UPPER FRONT BUMPER RETAINER

a.

Install the retainer with the 3 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 52119A 12.INSTALL FRONT BUMPER COVER

a.

Install the front bumper cover (See page Vehicle Exterior>EXTERIOR PANELS / TRIM>FRONT BUMPER>INSTALLATION).


Hide 51405A 15.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY