Home › Drivetrain › A750E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION ASSEMBLY
RM1440E _52 Drivetrain _056133 A750E AUTOMATIC TRANSMISSION / TRANSAXLE _0273933 AUTOMATIC TRANSMISSION ASSEMBLY A

A750E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION ASSEMBLY  REMOVAL  


PROCEDURE

Hide 1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page Power Source / Network>1GR-FE BATTERY / CHARGING>GENERATOR>REMOVAL).


Hide 51405A 2.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

Hide 51450 3.REMOVE REAR ENGINE UNDER COVER ASSEMBLY

Hide 53736B 5.REMOVE FRONT NO. 1 FENDER APRON TO FRAME SEAL RH

Hide 37110 7.REMOVE PROPELLER SHAFT ASSEMBLY

Hide 17410 8.REMOVE FRONT EXHAUST PIPE ASSEMBLY

a.

Hide 17118 9.REMOVE MANIFOLD STAY

C171485

a.

Remove the 3 bolts and stay.


Hide 17119 10.REMOVE NO. 2 MANIFOLD STAY

C171486

a.

Remove the 3 bolts and stay.


Hide 33820B 11.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

C214587

a.

Remove the nut and clip, and disconnect the transmission control cable from the transmission.


Hide 32921 12.DISCONNECT NO. 1 OIL COOLER INLET TUBE AND NO. 1 OIL COOLER OUTLET TUBE

U150048

a.

Remove the 2 bolts to open the 2 No. 2 flexible hose clamps.


b.

Using a union nut wrench, disconnect the inlet tube and outlet tube from each oil cooler tube union.


Hide 28100 13.REMOVE STARTER ASSEMBLY

a.

Hide 32101A 14.REMOVE DRIVE PLATE AND TORQUE CONVERTER CLUTCH SETTING BOLT

U148189E01
2.113,0.98 2.055,1.014 false 2.108,0.954 2.074,0.974 false

a.

Remove the flywheel housing side cover.


b.
U148190E01
2.117,0.982 2.059,1.015 false 2.112,0.955 2.079,0.976 false

Turn the crankshaft to gain access to the 6 bolts and remove each bolt while holding the crankshaft pulley bolt with a wrench.


Hide 35000 15.SUPPORT AUTOMATIC TRANSMISSION ASSEMBLY

C112848

a.

Support the transmission with a transmission jack. Lift the transmission slightly from the crossmember.


Hide 51225B 16.REMOVE FRONT SUSPENSION MEMBER BRACKET LH AND RH

C216979

a.

Remove the 8 bolts and front suspension member bracket LH and RH.


Hide 51204 17.REMOVE NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY

C216980

a.

Remove the 4 bolts of the rear engine mounting insulator.


b.
C216981

Remove the 4 nuts, 4 bolts and frame crossmember.


Hide 12371 18.REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR

C216982

a.

Remove the bolt and rear engine mounting heat insulator.


b.

Remove the 4 bolts and rear engine mounting insulator from the transmission.


Hide 19.DISCONNECT WIRE HARNESS AND CONNECTOR

a.
C112849

Tilt the transmission downward.

NOTICE:

Make sure the cooling fan does not contact the fan shroud.



b.

Disconnect the park/neutral position switch connector, transmission wire connector and 2 speed sensor connectors.

HINT:

Detach the claw, press down the lever, and then disconnect the transmission wire connector.


U150233


c.

Detach the 2 connector clamps and 4 harness clamps, and disconnect the wire harness.


Hide 35104V 20.DISCONNECT BREATHER PLUG HOSE

C216991

a.

Disconnect the breather plug hose from the engine side.


Hide 35000 21.REMOVE AUTOMATIC TRANSMISSION ASSEMBLY

C157018

a.

Remove the 9 bolts and automatic transmission.

NOTICE:

Do not use excess force when prying the transmission assembly.



Hide 22.REMOVE HARNESS CLAMP BRACKET

C216984

a.

Remove the 4 bolts and 4 harness clamp brackets.


Hide 33823 23.REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET

C111232

a.

Remove the 2 bolts and transmission control cable bracket.


Hide 32000 24.REMOVE TORQUE CONVERTER CLUTCH ASSEMBLY

Hide 32000 25.INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY