1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page Power Source / Network>1GR-FE BATTERY / CHARGING>GENERATOR>REMOVAL).
51405A
2.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
51450
3.REMOVE REAR ENGINE UNDER COVER ASSEMBLY
53736
4.REMOVE FRONT FENDER APRON SEAL RH
53736B
5.REMOVE NO. 1 FRONT FENDER APRON TO FRAME SEAL RH
6.DRAIN AUTOMATIC TRANSMISSION FLUID
36179
7.REMOVE TRANSFER CASE LOWER PROTECTOR
Remove the 4 bolts and transfer case lower protector.
37140
8.REMOVE FRONT PROPELLER SHAFT ASSEMBLY
Remove the front propeller shaft (See page Drivetrain>DRIVE SHAFT / PROPELLER SHAFT>FRONT PROPELLER SHAFT ASSEMBLY>REMOVAL).
37110
9.REMOVE PROPELLER SHAFT ASSEMBLY
Remove the propeller shaft (See page Drivetrain>DRIVE SHAFT / PROPELLER SHAFT>PROPELLER SHAFT ASSEMBLY(for 4WD)>REMOVAL).
17410
10.REMOVE FRONT EXHAUST PIPE ASSEMBLY
Remove the front exhaust pipe assembly (See page Engine / Hybrid System>1GR-FE INTAKE / EXHAUST>EXHAUST PIPE>REMOVAL).
33820B
11.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY
Remove the nut and clip, and disconnect the transmission control cable from the automatic transmission.
32921
12.DISCONNECT NO. 1 INLET OIL COOLER TUBE AND NO. 1 OUTLET OIL COOLER TUBE
Remove the 2 bolts to open the 2 No. 2 flexible hose clamps.
Using a union nut wrench, disconnect the No. 1 oil cooler inlet tube and No. 1 oil cooler outlet tube from each oil cooler tube union.
17118
13.REMOVE MANIFOLD STAY
Remove the 3 bolts and stay.
17119
14.REMOVE NO. 2 MANIFOLD STAY
Remove the 3 bolts and stay.
28100
15.REMOVE STARTER ASSEMBLY
Remove the starter assembly (See page Engine / Hybrid System>1GR-FE STARTING>STARTER>REMOVAL).
32101A
16.REMOVE DRIVE PLATE AND TORQUE CONVERTER CLUTCH SETTING BOLT
Remove the flywheel housing side cover.
Turn the crankshaft to gain access to the 6 bolts and remove each bolt while holding the crankshaft pulley setting bolt with a wrench.
17.SUPPORT AUTOMATIC TRANSMISSION ASSEMBLY
Support the transmission with a transmission jack. Lift the transmission slightly from the crossmember.
51226A
18.REMOVE FRONT SUSPENSION MEMBER BRACKET LH AND RH
Remove the 8 bolts and front suspension member bracket LH and RH.
51204
19.REMOVE NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY
Remove the 4 bolts of the rear engine mounting insulator.
Remove the 4 nuts, 4 bolts and frame crossmember.
12371
20.REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR
Remove the bolt and rear engine mounting heat insulator.
Remove the 4 bolts and rear engine mounting insulator from the transmission.
21.DISCONNECT WIRE HARNESS AND CONNECTOR
Remove the nut and disconnect the ground cable.
Tilt the transmission downward.
Make sure the cooling fan does not contact the fan shroud.
Disconnect the park/neutral position switch connector, transmission wire connector, 2 transmission speed sensor connectors and transfer control side connectors.
Detach the claw, press down the lever, and then disconnect the transmission wire connector.
Detach the 2 connector clamps and 7 harness clamps, and disconnect wire harness.
35104V
22.DISCONNECT BREATHER PLUG HOSE
Disconnect the 3 breather plug hoses from the engine.
35000
23.REMOVE AUTOMATIC TRANSMISSION ASSEMBLY
Remove the 9 bolts and transmission.
Do not use excess force when prying the transmission assembly.
36100
24.REMOVE TRANSFER ASSEMBLY
Remove the transfer (See page Drivetrain>VF4BM TRANSFER / 4WD / AWD>TRANSFER ASSEMBLY>REMOVAL).
33823
25.REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET
Remove the 2 bolts and control cable bracket.
32000
26.REMOVE TORQUE CONVERTER CLUTCH ASSEMBLY
32000
27.INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY
Inspect the torque converter clutch (See page Drivetrain>A750F AUTOMATIC TRANSMISSION / TRANSAXLE>TORQUE CONVERTER CLUTCH AND DRIVE PLATE>INSPECTION).