Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2010.08
RM1440E _54 Brake _056142 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0274004 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  Brake Warning Light Remains ON  


DESCRIPTION

The brake warning light comes on when brake fluid is insufficient, the parking brake is applied or the EBD is defective.

WIRING DIAGRAM

C214520E02
0.978,3.578 1.528,3.748 0.549,0.170 10 Brake 0.474,4.52 1.709,4.792 1.235,0.272 10 Combination Meter 3.043,4.377 4.402,4.598 1.360,0.221 10 Parking Brake Switch 3.024,2.879 4.546,3.234 1.522,0.355 10 Main Body ECU (Driver Side Junction Block) 5.364,4.302 6.989,4.667 1.626,0.364 10 Master Cylinder Solenoid (Skid Control ECU) 0.8,5.158 3.243,5.351 2.443,0.193 10 : CAN Communication System 1.277,1.201 1.558,1.367 0.281,0.165 10 IG+ 0.474,4.341 0.767,4.520 0.293,0.179 10 F14 3.043,4.23 3.282,4.427 0.239,0.198 10 A2 3.239,3.831 3.371,4.005 0.133,0.174 10 1 3.024,2.706 3.272,2.881 0.248,0.174 10 2D 2.902,2.065 3.132,2.254 0.230,0.188 10 17 3.225,2.173 3.654,2.361 0.429,0.188 10 PKB 5.364,4.13 5.617,4.295 0.253,0.165 10 A6

CAUTION / NOTICE / HINT

NOTICE:

When replacing the master cylinder solenoid, perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).


PROCEDURE

1.CHECK FOR DTC
a.

Check for DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is not output A
DTC is output B



A

2.CHECK CAN COMMUNICATION LINE

B

2.CHECK CAN COMMUNICATION LINE

OK

3.READ VALUE USING INTELLIGENT TESTER (PARKING BRAKE SW)

NG

GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

3.READ VALUE USING INTELLIGENT TESTER (PARKING BRAKE SW)
a.

Turn the ignition switch off.


b.

Connect the intelligent tester tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the intelligent tester tester on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Parking Brake SW Parking brake switch/ ON or OFF ON: Parking brake applied
OFF: Parking brake released
-


f.

Using the intelligent tester, check the input of the switch operation when the parking brake pedal is operated.

OK:

When the parking brake is operated, the display changes as shown above.




OK

4.READ VALUE USING INTELLIGENT TESTER (BRAKE WARNING LIGHT)

NG

5.INSPECT PARKING BRAKE SWITCH
4.READ VALUE USING INTELLIGENT TESTER (BRAKE WARNING LIGHT)
a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Brake Warning Light Brake warning light/ ON or OFF ON: Warning light on
OFF: Warning light off
-


f.

When performing the Brake Warning Light Active Test, check Brake Warning Light in the Data List (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST).

ABS/VSC/TRC
Tester Display Test Part Control Range Diagnostic Note
Brake Warning Light Brake warning light Warning light ON/OFF Observe the combination meter.


Result
Result Proceed to
Data List Display Data List Display when Performing Active Test ON/OFF Operation
ON Does not change between ON and OFF A
Changes between ON and OFF B
OFF Does not change between ON and OFF A
Changes between ON and OFF B


A

REPLACE MASTER CYLINDER SOLENOID

B

GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

5.INSPECT PARKING BRAKE SWITCH
a.

Disconnect the A2 parking brake switch connector.


b.
C215408E01
0.223,0.014 0.560,0.229 0.336,0.215 10 *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 - Body ground Parking brake applied
(Switch pin not pushed in)
Below 1 Ω
Parking brake released
(Switch pin pushed in)
10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Parking Brake Switch)



OK

6.CHECK HARNESS AND CONNECTOR (PARKING BRAKE SWITCH - MAIN BODY ECU [DRIVER SIDE JUNCTION BLOCK])

NG

REPLACE PARKING BRAKE SWITCH ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (PARKING BRAKE SWITCH - MAIN BODY ECU [DRIVER SIDE JUNCTION BLOCK])
a.

Disconnect the A2 parking brake switch connector.


b.

Disconnect the 2D main body ECU (driver side junction block assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A2-1 - 2D-17 (PKB) Always Below 1 Ω
A2-1 - Body ground Always 10 kΩ or higher




OK

REPLACE MAIN BODY ECU (DRIVER SIDE JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR