Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2010.08
RM1440E _54 Brake _056142 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0274004 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  TC and CG Terminal Circuit  


DESCRIPTION

DTC output mode is set by connecting terminals TC and CG of the DLC3.

WIRING DIAGRAM

C200425E14
1.242,4.317 3.194,4.509 1.951,0.193 10 : CAN Communication System 4.296,1.371 5.230,1.545 0.934,0.174 10 A6 4.296,1.563 7.112,1.752 2.816,0.188 10 Master Cylinder Solenoid (Skid Control ECU) 6.062,3.735 6.523,3.928 0.461,0.193 10 DLC3 6.062,3.557 6.329,3.741 0.267,0.184 10 F13 5.986,2.625 6.245,2.807 0.259,0.182 10 TC 5.978,2.988 6.291,3.190 0.313,0.202 10 CG 5.763,2.894 5.948,3.048 0.185,0.154 10 4 5.683,2.489 5.922,2.672 0.239,0.184 10 13 1.42,1.344 1.662,1.528 0.242,0.184 10 28 1.025,1.491 1.284,1.673 0.259,0.182 10 TC 0.635,2.016 0.977,2.209 0.342,0.193 10 F50 0.635,2.194 1.059,2.387 0.424,0.193 10 ECM

HINT:

When each warning light continues blinking, a ground short in the wiring of terminal TC of the DLC3 or an internal ground short in each ECU is suspected.


CAUTION / NOTICE / HINT

NOTICE:

When replacing the master cylinder solenoid, perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).


PROCEDURE

1.INSPECT DLC3
a.

Turn the ignition switch to ON.


b.
U144691E01
0.108,0.087 0.413,0.237 0.304,0.151 10 *a 2.137,0.207 2.441,0.358 0.304,0.151 10 CG 2.205,1.943 2.510,2.094 0.304,0.151 10 TC 1.84,1.465 2.039,2.009 2.039,2.009 2.172,2.009 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F13-13 (TC) - F13-4 (CG) Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of DLC3



OK

2.CHECK CAN COMMUNICATION LINE

NG

4.CHECK HARNESS AND CONNECTOR (ECM - DLC3)
2.CHECK CAN COMMUNICATION LINE

OK

3.CHECK DTC (CAN COMMUNICATION SYSTEM)

NG

GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

3.CHECK DTC (CAN COMMUNICATION SYSTEM)
a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the intelligent tester on.


e.

Check for DTCs (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).

Result
Result Proceed to
CAN system DTC is not output A
CAN system DTC is output B



A

4.CHECK HARNESS AND CONNECTOR (ECM - DLC3)

B

GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

4.CHECK HARNESS AND CONNECTOR (ECM - DLC3)
a.

Turn the ignition switch off.


b.

Disconnect the F50 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F50-28 (TC) - F13-13 (TC) Always Below 1 Ω




OK

5.CHECK HARNESS AND CONNECTOR (DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (DLC3 - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F13-4 (CG) - Body ground Always Below 1 Ω




OK

6.CHECK ECM (DLC3 INPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK ECM (DLC3 INPUT)
a.

Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.


SST
09843-18040  

b.
U144691E01
0.108,0.087 0.413,0.237 0.304,0.151 10 *a 2.137,0.207 2.441,0.358 0.304,0.151 10 CG 2.205,1.943 2.510,2.094 0.304,0.151 10 TC 1.84,1.465 2.039,2.009 2.039,2.009 2.172,2.009 false

Check that the MIL is blinking.

Result
Result Proceed to
MIL is blinking A
MIL is not blinking B

Text in Illustration
*a Front view of DLC3



A

7.CHECK DTC (CAN COMMUNICATION SYSTEM)

B

REPAIR OR REPLACE WIRE HARNESS OR ECM

7.CHECK DTC (CAN COMMUNICATION SYSTEM)
a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the intelligent tester on.


e.

Check for DTCs (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).

Result
Result Proceed to
CAN communication system DTC is not output A
CAN communication system DTC is output B



A

REPLACE MASTER CYLINDER SOLENOID

B

GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)