Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2010.08
RM1440E _54 Brake _056142 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0274004 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1210  Zero Point Calibration of Yaw Rate Sensor Undone  C1336  Zero Point Calibration of Acceleration Sensor Undone  


DESCRIPTION

The skid control ECU receives signals from the yaw rate and acceleration sensor via the CAN communication system.

The yaw rate sensor has a built-in acceleration sensor and detects the vehicle's condition using 2 circuits (GL1, GL2). If there is trouble in the bus lines between the yaw rate and acceleration sensor and the CAN communication system, DTCs U0123 (yaw rate sensor communication trouble) and U0124 (acceleration sensor communication trouble) are stored.

The DTCs are also stored when the calibration has not been completed.

DTC Code DTC Detection Condition Trouble Area
C1210 Zero point calibration of the yaw rate sensor is incomplete.
·

Zero point calibration incomplete

·

Sensor installation

·

Yaw rate and acceleration sensor

·

Master cylinder solenoid (Skid control ECU)


C1336 Zero point calibration of the acceleration sensor is incomplete.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

When replacing the master cylinder solenoid, perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).


HINT:

When DTC U0123, U0124 and/or U0126 is output together with DTC C1210 and/or C1336, inspect and repair the trouble areas indicated by DTC U0123, U0124 and/or U0126 first (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>U0073).


PROCEDURE

1.PERFORM ZERO POINT CALIBRATION OF YAW RATE AND ACCELERATION SENSOR
a.

Perform zero point calibration of the yaw rate and acceleration sensor (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).



NEXT

2.PERFORM TEST MODE (SIGNAL CHECK)
2.PERFORM TEST MODE (SIGNAL CHECK)
a.

Turn the ignition switch off.


b.

Perform the signal check in the Test Mode Procedure (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).

OK:

All test mode DTCs are cleared.




OK

END

NG

3.CHECK YAW RATE AND ACCELERATION SENSOR INSTALLATION
3.CHECK YAW RATE AND ACCELERATION SENSOR INSTALLATION
a.

Turn the ignition switch off.


b.

Check that the yaw rate and acceleration sensor has been installed properly (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>YAW RATE AND ACCELERATION SENSOR>REMOVAL).

OK:

The sensor is tightened to the specified torque.

The sensor is not installed at an angle.




OK

4.READ VALUE USING INTELLIGENT TESTER (YAW RATE AND ACCELERATION SENSOR)

NG

INSTALL YAW RATE AND ACCELERATION SENSOR CORRECTLY

4.READ VALUE USING INTELLIGENT TESTER (YAW RATE AND ACCELERATION SENSOR)
a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Deceleration Sensor Acceleration sensor/ Min.: -18.183 m/s2, Max.: 18.183 m/s2 - Changes continuously during acceleration/deceleration.
Deceleration Sensor 2 Acceleration sensor 2/ Min.: -18.183 m/s2, Max.: 18.183 m/s2 - Changes continuously during acceleration/deceleration.
Yaw Rate Sensor Yaw rate sensor/ Min.: -128°/s, Max.: 127°/s Vehicle stationary: 0°/s
Right turn: -128 to 0°/s
Left turn: 0 to 127°/s
-
Yaw Rate Sensor 2 Yaw rate sensor 2/ Min.: -128°/s, Max.: 127°/s Vehicle stationary: 0°/s
Right turn: -128 to 0°/s
Left turn: 0 to 127°/s
-


f.

Check that the yaw rate and acceleration sensor output value is displayed on the intelligent tester.

OK:

The yaw rate and acceleration sensor output value is normal.


NOTICE:

Check the yaw rate and acceleration sensor signal after replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).




OK

REPLACE MASTER CYLINDER SOLENOID

NG