Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2013.08
RM1440E _54 Brake _056142 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0274004 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1380  Stop Light Control Relay Malfunction  


DESCRIPTION

Upon receiving the hill-start assist control operating signal from the master cylinder solenoid (skid control ECU), the Stop light control relay (Stop light switch assembly) contact turns on and the stop lights come on.

DTC No. DTC Detection Condition Trouble Area
C1380
·

When the voltage at the IG1 terminal is 9.5 V or more and the stop light control relay drive output (STPO) is ON, a signal is not input to the STP2 terminal for 5 seconds or more.


·

When the voltage at the IG1 terminal is 9.5 V or more and the stop light control relay drive output (STPO) is OFF, the signal at the STP terminal is different from the input signal at the STP2 for 5 seconds or more.


·

Stop light switch assembly

·

Stop light switch assembly circuit

·

Master cylinder solenoid (Skid control ECU)



WIRING DIAGRAM

C252945E04
1.521,1.094 1.938,1.26 0.417,0.167 10 false STOP 0.844,1.094 1.26,1.26 0.417,0.167 10 false ALT 5.938,1.865 6.448,2.104 0.51,0.24 10 false STPO 5.74,2.656 5.938,2.823 0.198,0.167 10 false 7 5.688,1.74 5.875,1.906 0.188,0.167 10 false 16 2.375,0.844 2.5,1.01 0.125,0.167 10 false 7 5.938,0.948 6.469,1.167 0.531,0.219 10 false STP2 0.948,1.958 2.375,2.219 1.427,0.26 10 false from Battery 2.417,3.406 2.771,3.583 0.354,0.177 10 false A41 2.396,3.583 4.323,3.938 1.927,0.354 10 false Stop Light Switch Assembly 5.333,4.802 5.677,5 0.344,0.198 10 false A6 5.323,4.958 6.99,5.323 1.667,0.365 10 false Master Cylinder Solenoid (Skid Control ECU) 4.094,2.677 4.271,2.906 0.177,0.229 10 false 1 2.865,4.375 4.188,4.625 1.323,0.25 10 false to Stop Light Circuit 5.688,0.823 5.885,0.99 0.198,0.167 10 false 45 5.938,2.792 6.427,3.073 0.49,0.281 10 false STP 2.375,2.646 2.49,2.813 0.115,0.167 10 false 2 4.094,0.844 4.302,1.073 0.208,0.229 10 false 3 4.094,1.76 4.26,2.01 0.167,0.25 10 false 4 2.552,2.781 2.969,2.948 0.417,0.167 10 false GND 2.563,0.938 2.813,1.104 0.25,0.167 10 false B 3.906,0.938 4.104,1.146 0.198,0.208 10 false L 3.698,1.854 4.094,2.073 0.396,0.219 10 false ACC 3.698,2.771 4.146,3.01 0.448,0.24 10 false OUT

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the master cylinder solenoid, perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).


·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:

When DTC C1425 is output together with DTC C1380, inspect and repair the trouble areas indicated by DTC C1425 first (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1425).


PROCEDURE

1.CHECK STOP LIGHT OPERATION
a.

Check that the stop lights come on when the brake pedal is depressed and go off when the brake pedal is released.

OK:
Condition Illumination Condition
Brake pedal depressed. ON
Brake pedal released. OFF




OK

2.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SW)

NG

INSPECT LIGHTING SYSTEM (STOP LIGHT CIRCUIT)

2.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SW)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Select the Data List on the intelligent tester (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST).

ABS/VSC/TRAC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch assembly / ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-


d.

Check that the stop light switch assembly condition observed on the intelligent tester changes according to brake pedal operation.

OK:

The intelligent tester displays ON or OFF according to brake pedal operation.




OK

3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (STOP LIGHT RELAY)

NG

8.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (STOP LIGHT RELAY)
a.

Select the Active Test on the intelligent tester (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST).

ABS/VSC/TRAC
Tester Display Test Part Control Range Diagnostic Note
Stop Light Relay Stop light control relay (Stop light switch assembly) Relay (Switch) ON/OFF Stop lights come on


b.

Perform the Active Test of the stop light control relay (stop light switch assembly) using the intelligent tester.


c.

Select the Data List on the intelligent tester (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST).

ABS/VSC/TRAC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Stop Light Relay Output Stop light control relay (Stop light switch assembly) output / ON or OFF ON: Relay output on
OFF: Relay output off
-


d.

Check for stop light control relay (stop light switch assembly) operation using the Data List and stop light operation by performing an Active Test.

Result:
Result Proceed to
Data List content and stop light operation are normal. A
Data List content and stop light operation are abnormal or Data List content is normal but stop lights do not turn on or off. B




A

4.CHECK HARNESS AND CONNECTOR (STP2 TERMINAL)

B

6.CHECK STOP LIGHT SWITCH ASSEMBLY
4.CHECK HARNESS AND CONNECTOR (STP2 TERMINAL)
a.
U180901E01
0.111,0.057 0.347,0.259 0.236,0.202 10 *a 2.539,1.538 2.539,1.873 false 2.346,1.886 2.748,2.049 0.402,0.163 10 STP2 1.621,0.323 1.857,0.514 0.235,0.192 10 A6

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


c.

Disconnect the A6 Master Cylinder Solenoid (Skid Control ECU) connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A6-45 (STP2) - Body ground Stop light switch assembly ON (Brake pedal depressed) 11 to 14 V
A6-45 (STP2) - Body ground Stop light switch assembly OFF (Brake pedal released) Below 1.5 V


Text in Illustration
*a Front view of wire harness connector
(to Master Cylinder Solenoid (Skid Control ECU))



OK

5.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP2 CIRCUIT)

5.RECONFIRM DTC
a.

Reconnect the Master Cylinder Solenoid (Skid Control ECU) connector.



c.

Turn the ignition switch to ON.


d.

Perform a road test.


e.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC C1380 is not output. A
DTC C1380 is output. B




A

B

REPLACE MASTER CYLINDER SOLENOID

6.CHECK STOP LIGHT SWITCH ASSEMBLY
a.

Check the stop light control relay (stop light switch assembly) (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION).

OK:

The stop light control relay (stop light switch assembly) is normal.




OK

7.CHECK HARNESS AND CONNECTOR (STPO TERMINAL)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (STPO TERMINAL)
a.
U180902E01
0.111,0.107 0.319,0.300 0.208,0.193 10 *a 2.896,0.651 3.322,0.828 0.427,0.177 10 STPO 2.655,1.15 2.861,0.78 false 1.646,0.348 1.896,0.551 0.249,0.202 10 A6

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


b.

Disconnect the A6 Master Cylinder Solenoid (Skid Control ECU) connector.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A6-16 (STPO) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Master Cylinder Solenoid (Skid Control ECU))



OK

REPLACE MASTER CYLINDER SOLENOID

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STPO CIRCUIT)

8.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
a.
U180903E01
0.111,0.09 0.314,0.266 0.203,0.176 10 *a 2.509,0.565 2.859,0.742 0.350,0.177 10 STP 1.684,1.133 2.457,0.677 false 1.624,0.374 1.920,0.530 0.295,0.156 10 A6

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


c.

Disconnect the A6 Master Cylinder Solenoid (Skid Control ECU) connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A6-7 (STP) - Body ground Stop light switch assembly ON (Brake pedal depressed) 11 to 14 V
A6-7 (STP) - Body ground Stop light switch assembly OFF (Brake pedal released) Below 1.5 V


Text in Illustration
*a Front view of wire harness connector
(to Master Cylinder Solenoid (Skid Control ECU))



OK

REPLACE MASTER CYLINDER SOLENOID

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)