Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2010.08
RM1440E _54 Brake _056142 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0274004 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1422  Master Cylinder Pressure Sensor Zero Point High Malfunction  C1456  Control Pressure Sensor Zero Point High  


DESCRIPTION

Refer to DTCs C1421, C1423, C1424, C1455, C1457 and C1458 (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1281).

DTC Code DTC Detection Condition Trouble Area
C1422 When the stop light switch is off, the PM/C1 terminal voltage is 0.86 V or higher for 5 seconds or more.
·

Stop light switch

·

Stop light switch circuit

·

Master cylinder pressure sensor circuit

·

Master cylinder solenoid (Master cylinder pressure sensor)


C1456 When the stop light switch is off, the PCTRL terminal voltage is 0.86 V or higher for 5 seconds or more.
·

Stop light switch

·

Stop light switch circuit

·

Pressure control sensor circuit

·

Master cylinder solenoid (Pressure control sensor)



CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the master cylinder solenoid, perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:

When DTC C1425 is output together with DTC C1422 and/or C1456, inspect and repair the trouble areas indicated by DTC C1425 first (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1425).


PROCEDURE

1.CHECK STOP LIGHT OPERATION
a.

Check that the stop lights come on when the brake pedal is depressed and go off when the brake pedal is released.

OK:
Condition Illumination Condition
Brake pedal depressed On
Brake pedal released Off




OK

2.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SW)

NG

GO TO LIGHTING SYSTEM (PROBLEM SYMPTOMS TABLE)

2.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SW)
a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch/ ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-


f.

Check that the stop light condition observed on the intelligent tester changes according to brake pedal operation.

OK:

The intelligent tester displays ON or OFF according to brake pedal operation.




OK

3.CHECK BRAKE PEDAL AND STOP LIGHT SWITCH INSTALLATION

NG

5.CHECK TERMINAL VOLTAGE (STP)
3.CHECK BRAKE PEDAL AND STOP LIGHT SWITCH INSTALLATION
a.

Turn the ignition switch off.


b.

Check the brake pedal height and stop light switch installation (See page Brake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL>ADJUSTMENT).

OK:

The brake pedal height and stop light switch installation are normal.




OK

4.RECONFIRM DTC

NG

ADJUST BRAKE PEDAL OR STOP LIGHT SWITCH

4.RECONFIRM DTC

b.

Start the engine.


c.

Drive the vehicle at a speed of 40 km/h (25 mph) or more and perform a braking test (decelerate the vehicle by depressing the brake pedal).


d.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC C1422 is not output A
DTC C1422 is output B



A

B

REPLACE MASTER CYLINDER SOLENOID

5.CHECK TERMINAL VOLTAGE (STP)
a.

Disconnect the A6 skid control ECU connector.


b.
U180898E02
1.667,1.135 2.438,0.677 true 0.135,0.052 0.427,0.271 0.292,0.219 10 false *a 2.521,0.552 2.917,0.813 0.396,0.26 10 false STP 0.177,1.042 0.469,1.26 0.292,0.219 10 false A6

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A6-7 (STP) - Body ground Brake pedal depressed 8 to 14 V
Brake pedal released Below 1.5 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU)



OK

REPLACE MASTER CYLINDER SOLENOID

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP1 CIRCUIT)