Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2010.08
RM1440E _54 Brake _056142 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0274004 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  TRC OFF Indicator Light Remains ON  


DESCRIPTION

The skid control ECU is connected to the combination meter via the CAN communication system. Pressing the VSC OFF switch turns off traction control and pressing and holding this switch turns off traction control and VSC. If TRC control turns off, the TRC OFF indicator light comes on.

When the temperature inside the hydraulic brake booster becomes too high, the TRC OFF indicator light turns on and traction control is stopped until the temperature decreases.

for 4WD:

When the transfer is in L4, VSC is prohibited and the VSC OFF indicator and TRC OFF indicator lights turn on.

WIRING DIAGRAM

C219844E01
3.402,1.32 3.618,1.490 0.216,0.170 10 U6 3.402,1.535 4.530,1.723 1.128,0.188 10 VSC OFF Switch 4.528,0.937 4.674,1.107 0.146,0.170 10 6 3.248,0.937 3.376,1.093 0.128,0.156 10 3 5.788,1.059 6.185,1.228 0.397,0.170 10 CSW 5.541,0.937 5.672,1.107 0.132,0.170 10 9 2.328,3.119 2.627,3.312 0.299,0.193 10 F47 2.328,3.296 4.280,3.492 1.952,0.195 10 Four Wheel Drive Control ECU 3.449,2.717 3.753,2.892 0.304,0.174 10 RLP 3.841,2.708 4.076,2.885 0.235,0.177 10 15 2.954,2.082 3.258,2.280 0.304,0.198 10 IG 0.964,2.142 1.629,2.354 0.665,0.211 10 TRC OFF 0.469,2.824 0.792,3.017 0.323,0.193 10 F14 0.469,2.973 1.755,3.185 1.286,0.211 10 Combination Meter 1.291,0.806 1.614,0.999 0.323,0.193 10 +IG 5.801,2.866 6.290,3.031 0.489,0.165 10 EXI3*1 5.438,2.736 5.696,2.893 0.258,0.157 10 40 5.764,3.933 6.253,4.098 0.489,0.165 10 EXI3*2 5.401,3.803 5.658,3.960 0.258,0.157 10 40 3.776,3.908 4.830,4.071 1.054,0.163 10 from IG1 Circuit 5.46,4.448 5.711,4.631 0.251,0.184 10 A6 5.46,4.635 7.042,5.031 1.582,0.397 10 Master Cylinder Solenoid (Skid Control ECU) 0.999,4.274 2.926,4.472 1.927,0.198 10 : CAN Communication System 0.383,4.623 1.191,4.779 0.809,0.156 10 *1: for 4WD 0.383,4.954 1.184,5.137 0.802,0.184 10 *2: for 2WD

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the master cylinder solenoid, perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).

·

As there may be malfunctions in the transfer system related to when the transfer operates in L4, check the transfer system first (See page Drivetrain>VF4BM TRANSFER / 4WD / AWD>TRANSFER SYSTEM>INSPECTION).



PROCEDURE

1.CHECK CAN COMMUNICATION LINE

OK

2.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU CSW CIRCUIT)

NG

GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

2.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU CSW CIRCUIT)
a.

Disconnect the A6 skid control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A6-9 (CSW) - Body ground VSC OFF switch not pushed in 10 kΩ or higher
VSC OFF switch pushed in Below 1 Ω




OK

3.CHECK TERMINAL VOLTAGE (EXI3)

NG

5.INSPECT VSC OFF SWITCH
3.CHECK TERMINAL VOLTAGE (EXI3)
a.

Disconnect the A6 skid control ECU connector.


b.
U150103E02
2,1.542 2.083,1.958 2.083,1.958 2.208,1.958 false 0.125,0.115 0.438,0.365 0.313,0.25 10 false *a 2.26,1.885 2.646,2.073 0.385,0.188 10 false EXI3 1.635,0.479 1.896,0.708 0.26,0.229 10 false A6

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A6-40 (EXI3) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU)

Result
Result Proceed to
OK A
NG (for 4WD) B
NG (for 2WD) C



A

4.READ VALUE USING INTELLIGENT TESTER (TRC/VSC OFF MODE)

B

7.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU EXI3 CIRCUIT)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.READ VALUE USING INTELLIGENT TESTER (TRC/VSC OFF MODE)
a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
TRC/VSC Off Mode TRC/VSC off mode/ Normal, TRC OFF or VSC OFF Normal: Normal mode
TRC OFF: TRC OFF mode
VSC OFF: VSC OFF mode
-

f.

Check that the mode display changes according to VSC OFF switch operation.

OK:

Display changes according to switch operation.




OK

GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

NG

REPLACE MASTER CYLINDER SOLENOID

5.INSPECT VSC OFF SWITCH

b.
C215409E03
0.221,0.063 0.520,0.285 0.299,0.222 10 *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
6 - 3 Switch is not pushed 10 kΩ or higher
Switch is pushed Below 1 Ω


Text in Illustration
*a Component without harness connected
(VSC OFF Switch)



OK

6.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - VSC OFF SWITCH)

NG

6.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - VSC OFF SWITCH)
a.

Disconnect the A6 skid control ECU connector.


b.

Disconnect the U6 VSC OFF switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A6-9 (CSW) - U6-6 Always Below 1 Ω
A6-9 (CSW) - Body ground Always 10 kΩ or higher
U6-3 - Body ground Always Below 1 Ω




OK

REPLACE MASTER CYLINDER SOLENOID

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU EXI3 CIRCUIT)
a.

Disconnect the A6 skid control ECU connector.


b.

Disconnect the F47 four wheel drive control ECU connector.


c.
U150103E02
2,1.542 2.083,1.958 2.083,1.958 2.208,1.958 false 0.125,0.115 0.438,0.365 0.313,0.25 10 false *a 2.26,1.885 2.646,2.073 0.385,0.188 10 false EXI3 1.635,0.479 1.896,0.708 0.26,0.229 10 false A6

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A6-40 (EXI3) - Body ground Always 10 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU)



OK

8.CHECK TERMINAL VOLTAGE (EXI3)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK TERMINAL VOLTAGE (EXI3)
a.

Disconnect the A6 skid control ECU connector.


b.

Connect the F47 four wheel drive control ECU connector.


c.
U150103E02
2,1.542 2.083,1.958 2.083,1.958 2.208,1.958 false 0.125,0.115 0.438,0.365 0.313,0.25 10 false *a 2.26,1.885 2.646,2.073 0.385,0.188 10 false EXI3 1.635,0.479 1.896,0.708 0.26,0.229 10 false A6

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A6-40 (EXI3) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU)



OK

REPLACE MASTER CYLINDER SOLENOID

NG

REPLACE 4 WHEEL DRIVE CONTROL ECU NO.2