This DTC is stored when a malfunction occurs in the speakers.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| B15C3 | A short is detected in the speaker output circuit. | ·
Harness or connector ·
Speaker ·
Radio and display receiver assembly |
Disconnect the G35 and G36 radio and display receiver assembly connectors.
Disconnect the H1 and I1 front No. 1 speaker assembly connectors.
Disconnect the G1 and G12 front No. 2 speaker assembly connectors.
Disconnect the J1 and K1 rear speaker assembly connectors.
Disconnect the W5 and W6 rear No. 2 speaker assembly connectors.
Measure the resistance between the radio and display receiver assembly and body ground to check for a short circuit in the wire harness.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G35-1 (RR+) - Body ground | Always | 10 kΩ or higher |
| G35-2 (RL+) - Body ground | Always | 10 kΩ or higher |
| G35-3 (RR-) - Body ground | Always | 10 kΩ or higher |
| G35-6 (RL-) - Body ground | Always | 10 kΩ or higher |
| G36-1 (FR+) - Body ground | Always | 10 kΩ or higher |
| G36-2 (FL+) - Body ground | Always | 10 kΩ or higher |
| G36-5 (FR-) - Body ground | Always | 10 kΩ or higher |
| G36-6 (FL-) - Body ground | Always | 10 kΩ or higher |
Measure the resistance between each of the front No. 2 speaker assemblies and body ground to check for a short circuit in the wire harness.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G1-2 (TWL+) - Body ground | Always | 10 kΩ or higher |
| G1-4 (TWL-) - Body ground | Always | 10 kΩ or higher |
| G12-2 (TWR+) - Body ground | Always | 10 kΩ or higher |
| G12-4 (TWR-) - Body ground | Always | 10 kΩ or higher |
Measure the resistance between each of the rear speaker assemblies and rear No. 2 speaker assemblies to check for a short circuit in the wire harness.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J1-2 - Body ground | Always | 10 kΩ or higher |
| K1-2 - Body ground | Always | 10 kΩ or higher |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H1-1 - H1-2 | Always | 4 Ω |
| I1-1 - I1-2 | Always | 4 Ω |
| *a | Component without harness connected
(Front No. 1 Speaker Assembly) |
| *b | for RH |
| *c | for LH |
OK
NG
Replace the front No. 2 speaker assembly with a known good one (See page Audio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL).
Clear the DTCs (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>DTC CHECK / CLEAR).
Recheck for DTCs and check that no DTCs are output (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>DTC CHECK / CLEAR).
No DTCs are output.
Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.
When there is a possibility that either the right or left front speaker is defective, inspect by interchanging the right one with the left one.
Perform the above inspection on both LH and RH sides.
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J1-1 - J1-2 | Always | 4 Ω |
| K1-1 - K1-2 | Always | 4 Ω |
| *a | Component without harness connected
(Rear Speaker Assembly) |
| *b | for RH |
| *c | for LH |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| W5-1 - W5-2 | Always | 4 Ω |
| W6-1 - W6-2 | Always | 4 Ω |
| *a | Component without harness connected
(Rear No. 2 Speaker Assembly) |
| *b | for RH |
| *c | for LH |
OK
NG