Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM › 2009.08–2016.12
RM1440E _57 Power Source / Network _056154 NETWORKING _0274052 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2325  LIN Communication Bus Malfunction  


DESCRIPTION

The main body ECU (multiplex network body ECU) intermittently monitors the LIN communication bus between the components related to the doors and sliding roof drive gear sub-assembly*. DTC B2325 is stored when a malfunction in the LIN communication bus between the components related to the doors and sliding roof drive gear sub-assembly* is detected consecutively 3 times.

*: w/ Sliding Roof System


DTC Code DTC Detection Condition Trouble Area
B2325 The main body ECU (multiplex network body ECU) detects a malfunction in the LIN communication bus between components related to the doors and sliding roof drive gear sub-assembly* consecutively 3 times.
·

Multiplex network master switch assembly

·

Front power window regulator motor assembly LH

·

Front power window regulator motor assembly RH

·

Rear power window regulator motor assembly LH

·

Rear power window regulator motor assembly RH

·

Sliding roof drive gear sub-assembly*

·

Main body ECU (multiplex network body ECU)

·

Multiplex network door ECU (back door P/W)

·

Harness or connector



*: w/ Sliding Roof System


WIRING DIAGRAM

C214397E04
5.25,0.813 5.552,0.99 0.302,0.177 10 false A 5.74,0.385 6.094,0.563 0.354,0.177 10 false LIN2 3.5,2.052 3.771,2.229 0.271,0.177 10 false LIN 1.24,0.385 1.51,0.563 0.271,0.177 10 false LIN 3.5,0.385 3.813,0.563 0.313,0.177 10 false LIN1 3.854,0.302 4.063,0.479 0.208,0.177 10 false 17 3.104,0.385 3.427,0.563 0.323,0.177 10 false LIN2 2.844,0.302 3.052,0.479 0.208,0.177 10 false 16 5.49,0.302 5.667,0.479 0.177,0.177 10 false 16 3.844,1.958 3.979,2.135 0.135,0.177 10 false 9 1.573,0.302 1.708,0.479 0.135,0.177 10 false 9 3.521,3.094 3.792,3.271 0.271,0.177 10 false LIN 5.729,3.104 6,3.281 0.271,0.177 10 false LIN 3.865,3.01 4,3.188 0.135,0.177 10 false 9 5.542,3.01 5.677,3.188 0.135,0.177 10 false 9 5.74,4.854 6.156,5.031 0.417,0.177 10 false MPX1 5.542,4.781 5.677,4.958 0.135,0.177 10 false 4 5.25,0.958 6.927,1.354 1.677,0.396 10 false Main Body ECU (Multiplex Network Body ECU) 2.75,0.833 3.917,1.01 1.167,0.177 10 false h1 2.75,0.99 4.417,1.323 1.667,0.333 10 false Multiplex Network Master Switch Assembly 0.063,0.823 0.969,1 0.906,0.177 10 false I2 0.063,0.969 2.073,1.344 2.01,0.375 10 false Front Power Window Regulator Motor Assembly LH 1.698,1.865 3.01,2.417 1.313,0.552 10 false Front Power Window Regulator Motor Assembly RH 1.698,1.708 2.583,1.885 0.885,0.177 10 false H2 1.719,2.781 2.125,2.958 0.406,0.177 10 false K2 0.094,6.479 2.146,6.656 2.052,0.177 10 false *: w/ Sliding Roof System 1.719,2.927 3.021,3.469 1.302,0.542 10 false Rear Power Window Regulator Motor Assembly LH 5.042,3.552 5.448,3.729 0.406,0.177 10 false J2 5.042,3.698 7.021,4.031 1.979,0.333 10 false Rear Power Window Regulator Motor Assembly RH 5.375,5.302 5.781,5.479 0.406,0.177 10 false S8 5.354,5.469 6.698,5.833 1.344,0.365 10 false Sliding Roof Drive Gear Sub-assembly* 3.396,4.865 3.802,5.042 0.406,0.177 10 false MPX1 3.865,4.781 4.083,4.958 0.219,0.177 10 false 16 1.563,4.594 1.969,4.771 0.406,0.177 10 false V2 1.563,4.74 3.021,5.281 1.458,0.542 10 false Multiplex Network Door ECU (Back Door P/W)

CAUTION / NOTICE / HINT

NOTICE:
·

When using the intelligent tester with the ignition switch off to troubleshoot:

Connect the intelligent tester to the vehicle and turn a courtesy light switch on and off at 1.5 second intervals until communication between the intelligent tester and vehicle begins.

·

Inspect the fuses and bulbs for circuits related to this system before performing the following inspection procedure.



HINT:

When DTC B2325 and a LIN communication stop DTC are output simultaneously, first perform troubleshooting for the LIN communication stop DTC. Then perform troubleshooting for DTC B2325.


PROCEDURE

1.CLEAR DTC

NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B2325 is not output.




OK

NG

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - MULTIPLEX NETWORK MASTER SWITCH)
3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - MULTIPLEX NETWORK MASTER SWITCH)
a.

Remove the main body ECU (multiplex network body ECU) from the driver side junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.

Disconnect the h1 multiplex network master switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-16 (LIN2) - h1-17 (LIN1) Always Below 1 Ω
A-16 (LIN2) or h1-17 (LIN1) - Body ground Always 10 kΩ or higher




OK

4.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CLEAR DTC
a.

Install the main body ECU (multiplex network body ECU) to the driver side junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>INSTALLATION).


b.

Connect the h1 multiplex network master switch assembly connector.


c.

Disconnect the I2 front power window regulator motor assembly LH connector.




NEXT

5.CHECK FOR DTC
5.CHECK FOR DTC
a.

Check for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2325 is output A
DTC B2325 is not output B



A

6.CLEAR DTC

B

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

6.CLEAR DTC
a.

Connect the I2 front power window regulator motor assembly LH connector.


b.

Disconnect the h1 multiplex network master switch assembly connector.




NEXT

7.CHECK FOR DTC
7.CHECK FOR DTC
a.

Check for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2325 is output A
DTC B2325 is not output B



A

8.CLEAR DTC

B

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

8.CLEAR DTC
a.

Connect the h1 multiplex network master switch assembly connector.


b.

Disconnect the H2 front power window regulator motor assembly RH connector.




NEXT

9.CHECK FOR DTC
9.CHECK FOR DTC
a.

Check for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2325 is output A
DTC B2325 is not output B



A

10.CLEAR DTC

B

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

10.CLEAR DTC
a.

Connect the H2 front power window regulator motor assembly RH connector.


b.

Disconnect the J2 rear power window regulator motor assembly RH connector.




NEXT

11.CHECK FOR DTC
11.CHECK FOR DTC
a.

Check for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2325 is output A
DTC B2325 is not output B



A

12.CLEAR DTC

B

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

12.CLEAR DTC
a.

Connect the J2 rear power window regulator motor assembly RH connector.


b.

Disconnect the K2 rear power window regulator motor assembly LH connector.




NEXT

13.CHECK FOR DTC
13.CHECK FOR DTC
a.

Check for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2325 is output A
DTC B2325 is not output B



A

14.CLEAR DTC

B

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

14.CLEAR DTC
a.

Connect the K2 rear power window regulator motor assembly LH connector.


b.

Disconnect the V2 multiplex network door ECU (back door P/W) connector.




NEXT

15.CHECK FOR DTC
15.CHECK FOR DTC
a.

Check for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2325 is output (w/ Sliding Roof System) A
DTC B2325 is output (w/o Sliding Roof System) B
DTC B2325 is not output C



A

16.CLEAR DTC

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

REPLACE MULTIPLEX NETWORK DOOR ECU

16.CLEAR DTC
a.

Connect the V2 multiplex network door ECU (back door P/W) connector


b.

Disconnect the S8 sliding roof drive gear sub-assembly connector.




NEXT

17.CHECK FOR DTC
17.CHECK FOR DTC
a.

Check for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2325 is output A
DTC B2325 is not output B



A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY