Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM › from 2013.08
RM1440E _58 Vehicle Interior _056156 THEFT DETERRENT / KEYLESS ENTRY _0274067 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Security Indicator Light Circuit  


DESCRIPTION

When the theft deterrent system is in the disarmed state, the security indicator light (telltale light assembly) flashes continuously when the engine immobiliser system is set, and does not illuminate when the engine immobiliser system is not set.

When the theft deterrent system is in the armed state, the engine immobiliser system is automatically set and the security indicator light (telltale light assembly) flashes continuously.

When the theft deterrent system is in the arming preparation state or alarm sounding state, the main body ECU (multiplex network body ECU) causes the security indicator light to be illuminated.


WIRING DIAGRAM

B353562E10
1.021,1.875 1.313,2.052 0.292,0.177 10 false F35 1,2.031 2.5,2.615 1.5,0.583 10 false Security Indicator Light (Telltale Light Assembly) 4.688,1.875 4.979,2.052 0.292,0.177 10 false A 4.656,2.031 6.333,2.667 1.677,0.635 10 false Main Body ECU (Multiplex Network Body ECU) 1.344,1.083 1.719,1.26 0.375,0.177 10 false GND 1.198,0.979 1.333,1.156 0.135,0.177 10 false 1 2.021,1.083 2.24,1.26 0.219,0.177 10 false LP 2.25,0.979 2.385,1.156 0.135,0.177 10 false 6 5.042,1.083 5.354,1.26 0.313,0.177 10 false IND 4.833,0.979 5.063,1.156 0.229,0.177 10 false 23

PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SECURITY INDICATOR)
a.

Operate the intelligent tester according to the steps on the display and select Active Test (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>THEFT DETERRENT SYSTEM>DATA LIST / ACTIVE TEST).

Main Body
Tester Display Test Part Control Range Diagnostic Note
Security Indicator Security indicator light ON/OFF The test is possible when the following conditions are met:
·

The key is in the ignition key cylinder



OK:

Security indicator light can be turned on and off using the intelligent tester.




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT SECURITY INDICATOR LIGHT (TELLTALE LIGHT ASSEMBLY)
2.INSPECT SECURITY INDICATOR LIGHT (TELLTALE LIGHT ASSEMBLY)
a.

Remove the security indicator light (telltale light assembly) (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SECURITY INDICATOR LIGHT ASSEMBLY>REMOVAL).


b.

Inspect the security indicator light (telltale light assembly) (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SECURITY INDICATOR LIGHT ASSEMBLY>INSPECTION).



OK

3.CHECK HARNESS AND CONNECTOR (TELLTALE LIGHT - MAIN BODY ECU AND BODY GROUND)

NG

REPLACE SECURITY INDICATOR LIGHT (TELLTALE LIGHT ASSEMBLY)

3.CHECK HARNESS AND CONNECTOR (TELLTALE LIGHT - MAIN BODY ECU AND BODY GROUND)
a.

Disconnect the F35 security indicator light (telltale light assembly) connector.


b.

Remove the main body ECU (multiplex network body ECU) (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F35-6 (LP) - A-23 (IND) Always Below 1 Ω
F35-1 (GND) - Body ground Always Below 1 Ω
F35-6 (LP) or A-23 (IND) - Body ground Always 10 kΩ or higher




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR