Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING UNIT
RM1440E _58 Vehicle Interior _056163 HEATING / AIR CONDITIONING _0274138 AIR CONDITIONING UNIT A

HEATING / AIR CONDITIONING  AIR CONDITIONING UNIT  REMOVAL  


PROCEDURE

Hide 1.DRAIN ENGINE COOLANT

a.

Drain the engine coolant (See page Engine / Hybrid System>1GR-FE COOLING>COOLANT>REPLACEMENT).


Hide 2.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM

Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 88710E 4.DISCONNECT AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY

E197374

a.

Using SST, remove the piping clamp.

SST
09870-00015  
09870-00025  

i.
E112919E02
2.348,1.375 2.677,1.545 0.330,0.170 10 SST 1.259,0.614 2.1,1.448 false 2.1,1.448 2.332,1.448 false

Attach SST to the piping clamp.

HINT:

Confirm the direction of the piping clamp claw and SST by referring to the illustration on the caution label.



ii.
E112920E06
3.01,1.479 2.552,1.917 false 2.552,1.917 2.354,1.917 false 2.958,0.365 2.823,0.365 2.823,0.365 2.719,0.698 false 1.375,0.292 1.198,0.292 1.198,0.292 1,0.698 false 0.646,0.156 0.833,0.354 0.188,0.198 10 false *a 2.5,0.156 2.688,0.354 0.188,0.198 10 false *b 2.167,1.823 2.344,2.01 0.177,0.188 10 false *1 2.99,0.26 3.313,0.427 0.323,0.167 10 false SST 1.406,0.208 1.729,0.375 0.323,0.167 10 false SST

Push down SST and release the clamp lock.

Text in Illustration
*1 Release Lever
*a Pull
*b Push

NOTICE:

Be careful not to deform the tubes when pushing SST.



iii.

Pull SST slightly and push the release lever, then remove the piping clamp with SST.


iv.

Remove the piping clamp from SST.



b.

Disconnect the air conditioning tube and accessory assembly.

NOTICE:

Cap the open fittings immediately to keep moisture or dirt out of the system.



c.

Remove the grommet.


Hide 87245A 5.DISCONNECT INLET HEATER WATER HOSE AND OUTLET HEATER WATER HOSE

a.
E197375

Using pliers, grip the claws of the clips and slide the 2 clips.


b.

Disconnect the 2 heater water hoses.


Hide 85110 6.REMOVE WINDSHIELD WIPER MOTOR ASSEMBLY

a.

Remove the windshield wiper motor assembly (See page Vehicle Exterior>WIPER / WASHER>FRONT WIPER MOTOR>REMOVAL).


Hide 55301 7.REMOVE INSTRUMENT PANEL SUB-ASSEMBLY

Hide 45250 8.REMOVE STEERING COLUMN ASSEMBLY

a.

Remove the steering column (See page Steering>STEERING COLUMN>STEERING COLUMN ASSEMBLY>REMOVAL).


Hide 9.REMOVE FRONT SEAT ASSEMBLY LH

a.

for Manual Seat:

Remove the front seat assembly LH (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>REMOVAL).


b.

for Power Seat:

Remove the front seat assembly LH (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Power Seat)>REMOVAL).


Hide 10.REMOVE FRONT SEAT ASSEMBLY RH

NOTICE:

Use the same procedure described for the LH side.


a.

for Manual Seat:

Remove the front seat assembly RH (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>REMOVAL).


b.

for Power Seat:

Remove the front seat assembly RH (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Power Seat)>REMOVAL).


Hide 58510C 11.REMOVE FRONT FLOOR CARPET ASSEMBLY

HINT:

It is not necessary to fully remove the floor carpet. Partially remove it so that the rear air duct can be removed in a later step.


Hide 87212G 12.REMOVE REAR NO. 3 AIR DUCT

a.
E197378

Detach the 3 clamps, 4 claws and remove the rear No. 3 air duct.


Hide 87212 13.REMOVE REAR NO. 1 AIR DUCT

a.
E197379

Detach the 3 clamps, 4 claws and remove the rear No. 1 air duct.


Hide 58861B 14.REMOVE NO. 1 CONSOLE BOX DUCT

a.
E197380

Remove the clip and remove the No. 1 console box duct.


Hide 55347A 15.REMOVE NO. 1 INSTRUMENT PANEL BRACE MOUNTING BRACKET LH

a.
E197383

Remove the 2 nuts, bolt and the instrument panel brace.


Hide 55347A 16.REMOVE NO. 1 INSTRUMENT PANEL BRACE MOUNTING BRACKET RH

a.
E197384

Remove the 2 nuts, bolt and the instrument panel brace.


Hide 87201 17.REMOVE NO. 1 AIR DUCT SUB-ASSEMBLY

a.
E197381

Detach the 3 claws and remove the duct.


Hide 87201B 18.REMOVE NO. 2 AIR DUCT SUB-ASSEMBLY

a.
E197382

Remove the screw.


b.

Detach the 2 claws and the air duct.


Hide 19.REMOVE INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONING UNIT ASSEMBLY

a.

Disconnect the clamps and disconnect the connectors and wire harness.

E197385


b.

Remove the instrument panel reinforcement assembly with air conditioning unit assembly.

i.

Remove the 5 caps.


ii.

Using a T40"TORX" socket, remove the 5 "TORX" bolts.


iii.

Using a 12 mm hexagon wrench, remove the 2 collars.


iv.

Remove the bolts, nuts and the instrument panel reinforcement assembly with air conditioning unit assembly.

E200829



Hide 55330B 20.REMOVE INSTRUMENT PANEL REINFORCEMENT ASSEMBLY

a.
U150484

Remove the 5 bolts.


b.

Detach the 2 claws and the instrument panel reinforcement assembly.