Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM
RM1440E _59 Vehicle Exterior _056166 WINDOW / GLASS _0274161 POWER WINDOW CONTROL SYSTEM J

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  Auto Up / Down Function does not Operate  


DESCRIPTION

If the auto up/down function does not operate, the cause may be one or more of the following:

·

The ECU in the back door power window regulator motor determines that the back door power window regulator motor has not been initialized.

·

The rear back door power window regulator switch has a malfunction.

·

The Hall IC in the back door power window regulator motor has a malfunction.

·

There is an open or short in the wiring between the back door power window regulator switch and back door power window regulator motor.


WIRING DIAGRAM

B245634E02
4.948,3.917 6.854,4.594 1.906,0.677 10 Multiplex Network Door ECU (Back Door P/W) 0.521,3.896 2.802,4.583 2.281,0.688 10 Back Door Power Window Regulator Switch Assembly 0.542,3.698 1.135,3.875 0.594,0.177 10 f1 5.083,2.615 5.458,2.875 0.375,0.26 10 21 5.073,2.823 5.5,3.146 0.427,0.323 10 V2 5.375,2.823 6.031,3.25 0.656,0.427 10 AUTO 5.063,0.594 5.375,0.823 0.313,0.229 10 12 5.021,0.802 5.583,1.146 0.563,0.344 10 W10 5.375,0.792 5.948,1.083 0.573,0.292 10 AUT2 1.49,0.792 2.198,1.052 0.708,0.26 10 AUTO 2.042,0.656 2.344,0.917 0.302,0.26 10 4 1.563,1.25 2.094,1.583 0.531,0.333 10 GND 2.042,1.135 2.521,1.448 0.479,0.313 10 1 0.479,1.844 2.521,2.188 2.042,0.344 10 Back Door Power Window Regulator Motor Assembly 0.49,1.656 1.083,1.833 0.594,0.177 10 W9 1.51,2.813 2.073,3.083 0.563,0.271 10 AUTO 2.031,2.719 2.375,2.958 0.344,0.24 10 8 1.781,3.313 1.917,3.479 0.135,0.167 10 E 2.031,3.198 2.323,3.49 0.292,0.292 10 1 5.104,1.052 5.302,1.24 0.198,0.188 10 1 5.0,1.26 5.5,1.573 0.5,0.313 10 W10 5.385,1.229 5.771,1.552 0.385,0.323 10 E4

CAUTION / NOTICE / HINT

HINT:

Since the power window control system has functions that use LIN communication, first confirm that there is no malfunction in the communication system by inspecting the LIN communication functions in accordance with the "How to Proceed with Troubleshooting" procedures. Then, conduct the following inspection procedure.


PROCEDURE

1.CHECK FOR DTC

b.

Check for DTCs (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is not output A
DTC B2311 is output B
DTC B2312 is output C
DTC B2313 is output D
LIN communication system DTCs are output E



A

2.CHECK MANUAL UP/DOWN FUNCTION (BACK DOOR POWER WINDOW REGULATOR SWITCH ASSEMBLY)

B

C

D

E

2.CHECK MANUAL UP/DOWN FUNCTION (BACK DOOR POWER WINDOW REGULATOR SWITCH ASSEMBLY)
a.

Check that the manual up/down function using the back door power window regulator switch can operate the multiplex network door ECU (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>OPERATION CHECK).

OK:

Manual up/down function operates.




OK

3.READ VALUE USING INTELLIGENT TESTER (BACK DOOR POWER WINDOW REGULATOR SWITCH)

NG

GO TO "Manual Up / Down Function does not Operate on Back Door Only"

3.READ VALUE USING INTELLIGENT TESTER (BACK DOOR POWER WINDOW REGULATOR SWITCH)
a.

Use the Data List to check if the back door power window regulator switch is functioning properly (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>DATA LIST / ACTIVE TEST).

Back Door P/W
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Inside Back Door P/W Auto SW Back door power window regulator switch auto up/down signal / ON or OFF ON: Back door power window regulator auto up/down switch operated
OFF: Back door power window regulator switch not operated
-

OK:

On tester screen, item changes between ON and OFF according to above chart.




OK

4.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK DOOR ECU - BACK DOOR POWER WINDOW REGULATOR MOTOR ASSEMBLY)

NG

6.INSPECT BACK DOOR POWER WINDOW REGULATOR SWITCH ASSEMBLY
4.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK DOOR ECU - BACK DOOR POWER WINDOW REGULATOR MOTOR ASSEMBLY)
a.

Disconnect the W9 back door power window regulator motor connector.


b.

Disconnect the W10 multiplex network door ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W9-4 (AUTO) - W10-12 (AUT2) Always Below 1 Ω
W9-1 (GND) - W10-1 (E4) Always Below 1 Ω
W9-4 (AUTO) - Body ground Always 10 kΩ or higher




OK

5.CHECK MULTIPLEX NETWORK DOOR ECU (BACK DOOR P/W)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK MULTIPLEX NETWORK DOOR ECU (BACK DOOR P/W)
a.

Reconnect the multiplex network door ECU.

U149818E01
1.039,0.524 1.421,0.673 0.382,0.149 10 AUT2 4.25,2.054 4.598,2.203 0.347,0.149 10 GND 2.928,1.279 3.23,0.589 3.23,0.589 3.359,0.589 false 3.381,0.525 3.579,0.674 0.198,0.149 10 E4 4.765,0.416 5.580,0.599 0.816,0.184 10 Waveform 1 2.509,1.383 1.553,0.588 1.553,0.588 1.42,0.588 false 2.394,0.619 2.716,0.780 0.323,0.161 10 W10


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Tool Setting Switch Condition Specified Condition
W10-12 (AUT2) - W10-1 (E4) 2 V/DIV., 100 ms/DIV. Ignition switch ON, back door power window auto up or auto down function operating Pulse generation (See waveform 1)




OK

REPLACE BACK DOOR POWER WINDOW REGULATOR MOTOR ASSEMBLY

NG

REPLACE MULTIPLEX NETWORK DOOR ECU (BACK DOOR P/W)

6.INSPECT BACK DOOR POWER WINDOW REGULATOR SWITCH ASSEMBLY
a.
B215963E15
2.713,0.466 2.865,0.608 0.151,0.142 10 E 0.307,1.725 0.741,1.888 0.434,0.163 10 AUTO 2.116,0.951 2.511,0.535 2.511,0.535 2.688,0.535 false 1.351,1.312 1.003,1.802 1.003,1.802 0.831,1.802 false

Remove the back door power window regulator switch (See page Vehicle Exterior>WINDOW / GLASS>BACK POWER WINDOW SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
8 (AUTO) - 1 (E) Auto up/down operation Below 1 Ω
8 (AUTO) - 1 (E) Not operated 10 kΩ or higher




OK

7.CHECK HARNESS AND CONNECTOR (BACK DOOR POWER WINDOW REGULATOR SWITCH ASSEMBLY - MULTIPLEX NETWORK DOOR ECU AND BODY GROUND)

NG

REPLACE BACK DOOR POWER WINDOW REGULATOR SWITCH ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (BACK DOOR POWER WINDOW REGULATOR SWITCH ASSEMBLY - MULTIPLEX NETWORK DOOR ECU AND BODY GROUND)
a.

Disconnect the f1 back door power window regulator switch connector.


b.

Disconnect the V2 multiplex network door ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
f1-8 (AUTO) - V2-21 (AUTO) Always Below 1 Ω
f1-1 (E) - Body ground Always Below 1 Ω
f1-8 (AUTO) - Body ground Always 10 kΩ or higher




OK

REPLACE MULTIPLEX NETWORK DOOR ECU (BACK DOOR P/W)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR