Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM
RM1440E _59 Vehicle Exterior _056166 WINDOW / GLASS _0274161 POWER WINDOW CONTROL SYSTEM J

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  Manual Up / Down Function does not Operate on Back Door Only  


DESCRIPTION

If the back door power window does not operate, the retract switch in the rear wiper motor, the back door power window regulator motor or the wire harness may be abnormal.

WIRING DIAGRAM

B240838E01
4.768,5.066 6.577,5.444 1.809,0.378 10 Multiplex Network Door ECU (Back Door P/W) 0.745,5.12 2.491,5.461 1.746,0.341 10 Back Power Window Switch Assembly 0.745,4.928 1.341,5.103 0.596,0.174 10 f1 4.901,3.644 5.080,3.800 0.179,0.156 10 22 4.881,3.84 5.132,3.996 0.251,0.156 10 V2 5.182,3.826 5.620,3.982 0.438,0.156 10 BUP 4.877,1.903 5.070,2.059 0.193,0.156 10 14 4.827,2.079 5.153,2.235 0.326,0.156 10 W10 4.929,1.5 5.034,1.656 0.105,0.156 10 6 4.929,1.08 5.034,1.236 0.105,0.156 10 1 5.182,2.085 5.583,2.241 0.401,0.156 10 BUP2 5.189,1.689 5.590,1.845 0.401,0.156 10 BDR2 5.182,1.29 5.406,1.446 0.224,0.156 10 E4 1.758,2.077 1.989,2.247 0.231,0.170 10 UP 2.105,1.993 2.304,2.163 0.199,0.170 10 10 4.891,2.292 5.084,2.448 0.193,0.156 10 13 4.831,2.467 5.143,2.623 0.312,0.156 10 W10 5.178,2.466 5.579,2.622 0.401,0.156 10 BDN2 1.522,2.469 1.991,2.639 0.468,0.170 10 DOWN 1.66,1.285 2.013,1.455 0.353,0.170 10 GND 1.884,1.678 2.008,1.847 0.123,0.170 10 B 2.105,2.371 2.230,2.541 0.125,0.170 10 7 2.105,1.194 2.230,1.364 0.125,0.170 10 1 2.105,1.601 2.230,1.770 0.125,0.170 10 2 0.563,2.976 2.580,3.322 2.017,0.346 10 Back Door Power Window Regulator Motor Assembly 0.563,2.799 0.820,2.973 0.258,0.174 10 W9 1.772,3.828 2.012,3.998 0.239,0.170 10 UP 2.095,3.73 2.209,3.900 0.114,0.170 10 6 4.901,4.05 5.080,4.206 0.179,0.156 10 23 4.888,4.232 5.118,4.388 0.230,0.156 10 V2 5.182,4.246 5.620,4.402 0.438,0.156 10 BDN 1.52,4.238 1.992,4.408 0.472,0.170 10 DOWN 2.095,4.158 2.208,4.327 0.113,0.170 10 7 1.87,4.613 2.001,4.783 0.130,0.170 10 E 2.095,4.515 2.209,4.685 0.114,0.170 10 1 0.981,0.365 3.056,0.737 2.075,0.371 10 Back Door Lock Assembly (Back Door Courtesy light Switch) 4.827,1.29 5.153,1.446 0.326,0.156 10 W10 4.827,1.682 5.153,1.838 0.326,0.156 10 W10

PROCEDURE

1.SYSTEM CHECK
a.

Check the back door switch.


Result Proceed to
All back door switches do not operate A
Back door power window regulator switch does not operate B
Tail gate control switch does not operate C


A

2.CHECK LIGHTING SYSTEM (BACK DOOR COURTESY LIGHT SWITCH)

B

8.INSPECT BACK DOOR POWER WINDOW REGULATOR SWITCH ASSEMBLY

C

2.CHECK LIGHTING SYSTEM (BACK DOOR COURTESY LIGHT SWITCH)
a.

Use the Data List to check if the back door courtesy light switch is functioning properly (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>DATA LIST / ACTIVE TEST).

Back Door P/W
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Back Door Courtesy Switch Back door courtesy light switch signal / ON or OFF ON: Back door open
OFF: Back door closed
-


OK:

On tester screen, item changes between ON and OFF according to above chart.



OK

3.CHECK REAR WIPER SYSTEM (REAR WIPER POSITION)

NG

3.CHECK REAR WIPER SYSTEM (REAR WIPER POSITION)
a.

Use the Data List to check if the rear wiper is functioning properly (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>DATA LIST / ACTIVE TEST).

Back Door P/W
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Wiper Retracted Position Rear wiper reverse position switch signal / ON or OFF ON: Rear wiper reverse position switch is in ON position
OFF: Rear wiper reverse position switch is in OFF position
-
Wiper Reverse Position Rear wiper reverse position switch signal / ON or OFF ON: Rear wiper in reverse position
OFF: Rear wiper in other position
-


OK:

On tester screen, each item changes between ON and OFF according to above chart.



OK

4.CHECK FOR DTC (B2312)

NG

4.CHECK FOR DTC (B2312)
a.

Check if DTC B2312 is output (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B2312 is not output.




OK

5.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (BACK DOOR POWER WINDOW)

NG

5.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (BACK DOOR POWER WINDOW)
a.

Select the Active Test, use the intelligent tester to generate a control command, and then check that the door window regulator operates (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>DATA LIST / ACTIVE TEST).

Back Door P/W
Tester Display Test Part Control Range Diagnostic Note
Back Door power Window Back door power window OFF/UP/DOWN -

OK:

The power window regulator operates normally.




OK

REPLACE MULTIPLEX NETWORK DOOR ECU (BACK DOOR P/W)

NG

6.INSPECT BACK DOOR POWER WINDOW REGULATOR MOTOR ASSEMBLY
6.INSPECT BACK DOOR POWER WINDOW REGULATOR MOTOR ASSEMBLY
a.
B246366E01
1.896,3.181 2.229,2.955 2.229,2.955 2.317,2.955 false 1.664,3.181 1.332,2.955 1.332,2.955 1.243,2.955 false 2.332,2.88 2.671,3.022 0.339,0.142 10 GND 1.965,3.49 2.297,3.264 2.297,3.264 2.386,3.264 false 2.401,3.19 2.883,3.332 0.482,0.142 10 DOWN 1.111,2.88 1.223,3.022 0.112,0.142 10 B 1.596,3.49 1.263,3.264 1.263,3.264 1.174,3.264 false 0.914,3.19 1.130,3.332 0.216,0.142 10 UP 1.8,1.164 1.607,0.206 1.607,0.206 1.435,0.206 false 1.242,0.125 1.405,0.267 0.163,0.142 10 *1

Remove the back door power window regulator motor (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR(for Front Door)>REMOVAL).


b.

Check that the back door power window regulator motor moves smoothly as follows.

NOTICE:
·

Do not apply positive (+) battery voltage to any terminal other than terminal 2 (B) to avoid damaging the pulse sensor inside the motor.

·

Reset the door window regulator (initialize the pulse sensor) after installing the door window regulator to the door.



Measurement Condition Specified Condition
1.

Connect the positive (+) battery terminal to terminal 2 (B), and connect the negative (-) battery terminal to terminal 1 (GND), and keep them connected for 3 seconds or more.

2.

With terminals 2 (B) and 1 (GND) connected to the battery, connect the negative (-) battery terminal to terminal 10 (UP).

3.

Disconnect and reconnect the negative (-) battery terminal to terminal 10 (UP) within 1 second.


Motor gear rotates clockwise (Up)
1.

Connect the positive (+) battery terminal to terminal 2 (B), and connect the negative (-) battery terminal to terminal 1 (GND), and keep them connected for 3 seconds or more.

2.

With terminals 2 (B) and 1 (GND) connected to the battery, connect the negative (-) battery terminal to terminal 7 (DOWN).

3.

Disconnect and reconnect the negative (-) battery terminal to terminal 7 (DOWN) within 1 second.


Motor gear rotates counterclockwise (Down)

Text in Illustration
*1 Motor Gear
V100135

Clockwise
V100136

Counterclockwise



OK

7.CHECK HARNESS AND CONNECTOR (BACK DOOR POWER WINDOW REGULATOR MOTOR ASSEMBLY - MULTIPLEX NETWORK DOOR ECU)

NG

REPLACE BACK DOOR POWER WINDOW REGULATOR MOTOR ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (BACK DOOR POWER WINDOW REGULATOR MOTOR ASSEMBLY - MULTIPLEX NETWORK DOOR ECU)
a.

Disconnect the W9 back door power window regulator motor connector.


b.

Disconnect the W10 multiplex network door ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W9-10 (UP) - W10-14 (BUP2) Always Below 1 Ω
W9-7 (DOWN) - W10-13 (BDN2) Always Below 1 Ω
W9-10 (UP) - Body ground Always 10 kΩ or higher
W9-7 (DOWN) - Body ground Always 10 kΩ or higher




OK

REPLACE MULTIPLEX NETWORK DOOR ECU (BACK DOOR P/W)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT BACK DOOR POWER WINDOW REGULATOR SWITCH ASSEMBLY
a.

Remove the back door power window regulator switch (See page Vehicle Exterior>WINDOW / GLASS>BACK POWER WINDOW SWITCH>REMOVAL).


B215963E12
2.133,1.009 2.516,0.453 2.516,0.453 2.64,0.453 false 2.67,0.371 2.826,0.541 0.156,0.170 10 E 2.499,1.763 2.734,1.912 0.236,0.149 10 UP 0.38,1.763 0.856,1.912 0.475,0.149 10 DOWN 1.841,1.338 2.267,1.849 2.267,1.849 2.46,1.849 false 1.6,1.338 1.175,1.849 1.175,1.849 0.982,1.849 false

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
6 (UP) - 1 (E) Manual up operation Below 1 Ω
7 (DOWN) - 1 (E) Manual down operation Below 1 Ω
6 (UP) - 1 (E) Not operated 10 kΩ or higher
7 (DOWN) - 1 (E) Not operated 10 kΩ or higher




OK

9.CHECK HARNESS AND CONNECTOR (BACK DOOR POWER WINDOW REGULATOR SWITCH ASSEMBLY - MULTIPLEX NETWORK DOOR ECU)

NG

REPLACE BACK DOOR POWER WINDOW REGULATOR SWITCH ASSEMBLY

9.CHECK HARNESS AND CONNECTOR (BACK DOOR POWER WINDOW REGULATOR SWITCH ASSEMBLY - MULTIPLEX NETWORK DOOR ECU)
a.

Disconnect the f1 back door power window regulator switch connector.


b.

Disconnect the V2 multiplex network door ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
f1-6 (UP) - V2-22 (BUP) Always Below 1 Ω
f1-7 (DOWN) - V2-23 (BDN) Always Below 1 Ω
f1-1 (E) - Body ground Always Below 1 Ω
f1-6 (UP) - Body ground Always 10 kΩ or higher
f1-7 (DOWN) - Body ground Always 10 kΩ or higher




OK

REPLACE MULTIPLEX NETWORK DOOR ECU (BACK DOOR P/W)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR