56115A
1.INSTALL NO. 1 WINDSHIELD GLASS STOPPER
Install 2 new stoppers to the vehicle body as shown in the illustration.
| *1 | Stopper |
| *2 | Vehicle Body |
56116C
2.INSTALL NO. 2 WINDSHIELD GLASS STOPPER
Apply Primer G to the glass where the stoppers will be installed.
Allow the primer to dry for 3 minutes or more.
Throw away any leftover primer.
Do not apply too much primer.
Install 2 new stoppers to the glass at the locations shown in the illustration.
| *1 | Windshield Glass | - | - |
| *a | Backside | *b | Ceramic Notch |
| *c | Ceramic Line | d | Center |
| Area | Specified Condition |
|---|---|
| a | 14.2 mm (0.559 in.) |
75533G
3.INSTALL WINDSHIELD OUTSIDE UPPER MOULDING
Using a brush or sponge, coat the contact surface of the glass and moulding with Primer G as shown in the illustration.
Allow the primer coating to dry for 3 minutes or more.
Do not coat the adhesive with Primer G.
Throw away any leftover primer.
| *a | Backside | - | - |
| Area | Specified Condition |
|---|---|
| a | 6.9 mm (0.272 in.) |
Remove the peeling paper from a new windshield outside moulding. Install the moulding as shown in the illustration.
56117D
4.INSTALL WINDSHIELD GLASS ADHESIVE DAM
Apply Primer G to the glass where the glass adhesive dam will be installed.
Allow the primer to dry for 3 minutes or more.
Throw away any leftover primer.
Do not apply too much primer.
Remove the peeling paper from the adhesive part of a new dam. Install the dam (adhesive side) to the glass (Primer G area), but exclude the area above the notches on the upper part of the glass.
| *a | Backside | *b | Ceramic Notch |
| *c | Dam Center Line | - | - |
| Area | Specified Condition |
|---|---|
| a | 9.5 mm (0.374 in.) |
| b | 37.7 mm (1.48 in.) |
56111
5.INSTALL WINDSHIELD GLASS
Position the glass.
Using suction cups, place the glass in the correct position.
Check that the entire contact surface of the glass rim is perfectly even.
Place matchmarks on the glass and vehicle body at the locations indicated in the illustration.
Placing matchmarks is only necessary when installing new glass. When reinstalling the used glass, matchmarks should already be present.
When reusing the glass, check and correct the matchmark positions.
Check that the stoppers are attached to the vehicle body correctly.
Using suction cups, remove the glass.
| *a | Matchmark |
Using a brush, apply Primer M to the exposed part of the vehicle body.
Allow the primer to dry for 3 minutes or more.
Do not apply primer to the adhesive.
Throw away any leftover primer.
Do not apply too much primer.
| *1 | Primer M |
| *2 | Adhesive |
| *a | CORRECT |
| *b | INCORRECT |
Using a brush or sponge, apply Primer G to the contact surface of the glass.
| *1 | Primer M | - | - |
| *a | Backside | *b | Adhesive Center Line |
| Area | Specified Condition |
|---|---|
| a | 9.5 mm (0.374 in.) |
| b | 3.0 mm (0.118 in.) |
| c | 8.0 mm (0.315 in.) |
| d | 28.1 mm (1.11 in.) |
| e | 7.0 mm (0.276 in.) |
If the primer is applied to an area that is not specified, apply non-residue solvent to a clean cloth and wipe off the excess primer before it dries.
Allow the primer to dry for 3 minutes or more.
Throw away any leftover primer.
Do not apply too much primer.
Apply adhesive to the glass.
Toyota Genuine Windshield Glass Adhesive or equivalent
Cut off the tip of a cartridge nozzle as shown in the illustration.
After cutting off the tip, use all adhesive within the time written in the table below.
| Temperature | Usage Time Frame |
|---|---|
| 35°C (95°F) | 15 minutes |
| 20°C (68°F) | 1 hour 40 minutes |
| 5°C (41°F) | 8 hours |
Load a sealer gun with the cartridge.
Apply adhesive to the glass as shown in the illustration.
| *1 | Adhesive | - | - |
| *a | Backside | *b | Adhesive Center Line |
| Area | Specified Condition |
|---|---|
| a | 12.0 mm (0.472 in.) |
| b | 8.0 mm (0.315 in.) |
| c | 9.5 mm (0.374 in.) |
| d | 3.0 mm (0.118 in.) |
Install the glass to the vehicle body.
Using suction cups, position the glass so that the matchmarks are aligned. Press it in gently along the rim.
| *a | Matchmark |
Lightly press the outer surface of the glass to ensure that it is securely fit to the vehicle body.
Check that the stoppers are attached to the vehicle body correctly.
Check that the vehicle body and glass have a small gap between them.
If necessary, use a scraper to correct the level or position of adhesive that has been applied.
Apply adhesive to any areas where the amount of adhesive is inadequate.
| *1 | Dam |
| *2 | Adhesive |
| *3 | Windshield Glass |
Hold the glass in place securely with protective tape or equivalent until the adhesive hardens.
Do not drive the vehicle within the amount of time written in the table below.
| Temperature | Minimum Time Prior to Driving Vehicle |
|---|---|
| 35°C (95°F) | 1 hour 30 minutes |
| 20°C (68°F) | 5 hours |
| 5°C (41°F) | 24 hours |
w/ Windshield Deicer System:
Connect the windshield deicer connector.
75533E
6.INSTALL WINDSHIELD OUTSIDE MOULDING
Using a brush or sponge, apply Primer G to the glass where the moulding will be installed.
Do not apply too much primer.
Allow the primer coating to dry for 3 minutes or more.
Throw away any leftover primer.
If an area other than that specified is coated by accident, wipe off the primer with a clean piece of cloth before it dries.
Apply Primer G to the windshield outside moulding area "a" shown in the illustration.
Install a new moulding to the windshield glass as shown in the illustration.
56111
7.CHECK FOR LEAK AND REPAIR
Conduct a leak test after the adhesive has completely hardened.
Seal any leaks with auto glass sealer.
63310
8.INSTALL ROOF HEADLINING ASSEMBLY
Return the roof headlining to its original position. Refer to the following procedures (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION).
87810
9.INSTALL INNER REAR VIEW MIRROR ASSEMBLY (w/ EC Mirror)
87834
10.INSTALL INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)
87810
11.INSTALL INNER REAR VIEW MIRROR ASSEMBLY (w/o EC Mirror)
81260A
12.INSTALL MAP LIGHT ASSEMBLY
74348
13.INSTALL VISOR HOLDER
74320
14.INSTALL VISOR ASSEMBLY LH
74310
15.INSTALL VISOR ASSEMBLY RH
74318
16.INSTALL VISOR BRACKET COVER LH
74317
17.INSTALL VISOR BRACKET COVER RH
74610A
18.INSTALL ASSIST GRIP SUB-ASSEMBLY
62212
19.INSTALL FRONT PILLAR GARNISH LH
62211
20.INSTALL FRONT PILLAR GARNISH RH
74611F
21.INSTALL NO. 1 ASSIST GRIP
74617A
22.INSTALL ASSIST GRIP PLUG
62312B
23.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH
62311B
24.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH
62112
25.INSTALL COWL SIDE TRIM BOARD LH
62111C
26.INSTALL COWL SIDE TRIM BOARD RH
67920
27.INSTALL DOOR SCUFF PLATE ASSEMBLY LH
67910
28.INSTALL DOOR SCUFF PLATE ASSEMBLY RH
55781E
29.INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY
30.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH
31.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH
85292B
32.INSTALL FRONT WIPER ARM HEAD CAP
53867H
33.INSTALL FRONT FENDER TO COWL SIDE SEAL LH
53866J
34.INSTALL FRONT FENDER TO COWL SIDE SEAL RH
53883F
35.INSTALL FRONT FENDER MAIN SEAL LH
53882H
36.INSTALL FRONT FENDER MAIN SEAL RH
53292A
37.INSTALL UPPER RADIATOR SUPPORT SEAL
38.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).