Use the same procedure for both the RH and LH sides.
The procedure listed below is for the LH side.
1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
69278C
2.REMOVE REAR DOOR INSIDE HANDLE BEZEL LH
Using moulding remover, detach the 3 claws to remove the rear door inside handle bezel LH as shown in the illustration.
| *1 | Moulding Remover |
67604
3.REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH
Detach the 4 claws to remove the 2 door armrest caps.
Remove the 3 screws.
Remove the 9 clips.
Pull out the rear door trim board sub-assembly LH in the direction indicated by the arrow as shown in the illustration.
Raise the rear door trim board sub-assembly LH and detach the 4 claws and reference boss to remove the rear door trim board sub-assembly LH together with the rear door inner glass weatherstrip LH.
| *1 | Reference Boss |
Disconnect the connector.
Disconnect the rear door lock remote control cable assembly LH and rear door inside locking cable assembly LH as shown in the illustration.
Using a screwdriver, detach the claw to remove the clamp.
68174A
4.REMOVE REAR DOOR INNER GLASS WEATHERSTRIP LH
Using a screwdriver, detach the 3 claws to remove the rear door inner glass weatherstrip LH from the rear door trim board sub-assembly LH as shown in the illustration.
84810D
5.REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY
81230A
6.REMOVE COURTESY LIGHT ASSEMBLY
81090
7.REMOVE NO. 1 INTERIOR ILLUMINATION LIGHT ASSEMBLY (w/ TOYOTA Parking Assist-sensor System)
Using a screwdriver, detach the claw and remove the light.
| *1 | Protective Tape |
Tape the screwdriver tip before use.
Disconnect the connector.
86160B
8.REMOVE REAR SPEAKER ASSEMBLY
67842E
9.REMOVE REAR DOOR SERVICE HOLE COVER LH
Disconnect the connector.
Detach the 3 clamps and move the rear door wire out of the way to remove the rear door service hole cover LH.
Remove any remaining butyl tape from the rear door panel.
67674A
10.REMOVE REAR DOOR FRAME GARNISH LH
Detach the clip to remove the rear door frame garnish LH.
68152C
11.REMOVE REAR DOOR GLASS RUN LH
Remove the rear door glass run LH.
67408F
12.REMOVE REAR DOOR WINDOW REAR LOWER FRAME SUB-ASSEMBLY LH
Loosen the temporary bolt.
| *1 | Temporary Bolt |
Do not remove the temporary bolt. If the temporary bolt is removed, the rear door window rear lower frame sub-assembly LH may fall and cause damage.
Remove the 2 bolts and screw.
Remove the rear door window rear lower frame sub-assembly LH.
When the rear door window rear lower frame sub-assembly LH is removed, do not allow the rear door quarter window glass LH to fall.
Remove the temporary bolt from the rear door window rear lower frame sub-assembly LH.
68124C
13.REMOVE REAR DOOR QUARTER WINDOW GLASS LH
Remove the rear door quarter window glass LH and rear door quarter window weatherstrip LH as a unit as shown in the illustration.
68189
14.REMOVE REAR DOOR QUARTER WINDOW WEATHERSTRIP LH
Remove the rear door quarter window weatherstrip LH from the rear door quarter window glass LH.
68104
15.REMOVE REAR DOOR GLASS SUB-ASSEMBLY LH
Connect the rear power window regulator switch assembly.
Connect the cable to the negative (-) battery terminal.
Move the arm of the rear door window regulator sub-assembly LH so that the roller on the arm can be seen through the service hole.
Disconnect the cable from the negative (-) battery terminal.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
Disconnect the rear power window regulator switch assembly.
Remove the rear door glass sub-assembly LH from the rear door window regulator sub-assembly LH as shown in the illustration.
Remove the rear door glass sub-assembly LH as indicated by the arrows in the order shown in the illustration.
Do not damage the rear door glass sub-assembly LH.
69906B
16.REMOVE REAR DOOR GLASS CHANNEL SUB-ASSEMBLY LH
Using a screwdriver, remove the rear door glass channel sub-assembly LH.
| *1 | Protective Tape |
Tape the screwdriver tip before use.
69975A
17.REMOVE REAR DOOR GLASS CHANNEL FILLER
Remove the rear door glass channel filler.
69804
18.REMOVE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY LH
Disconnect the connector.
Loosen the temporary bolt.
| *1 | Temporary Bolt |
Do not remove the temporary bolt. If the temporary bolt is removed, the rear door window regulator sub-assembly LH may fall and cause damage.
Remove the 3 bolts.
Remove the rear door window regulator sub-assembly LH.
Remove the temporary bolt from the rear door window regulator sub-assembly LH.
85720G
19.REMOVE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
69060A
20.REMOVE REAR DOOR LOCK ASSEMBLY LH
69740D
21.REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH
Using a screwdriver, detach the claw to open the cover.
Tape the screwdriver tip before use.
Remove the rear door lock remote control cable assembly LH from the rear door lock assembly LH.
69780B
22.REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY LH
Using a screwdriver, detach the 3 claws to open the cover.
Tape the screwdriver tip before use.
Remove the rear door inside locking cable assembly LH from the rear door lock assembly LH.
69227L
23.REMOVE REAR DOOR OUTSIDE HANDLE COVER LH
Using a T30 "TORX" socket wrench, loosen the screw.
The screw cannot be removed because it is integrated into the rear door outside handle frame sub-assembly LH.
Detach the claw to remove the rear door outside handle cover LH.
69240
24.REMOVE REAR DOOR OUTSIDE HANDLE ASSEMBLY LH
Move the lever in the direction indicated by the arrow in the illustration.
Remove the rear door outside handle assembly LH as shown in the illustration.
69241G
25.REMOVE REAR DOOR FRONT OUTSIDE HANDLE PAD
Detach the 3 claws to remove the rear door front outside handle pad.
69242G
26.REMOVE REAR DOOR REAR OUTSIDE HANDLE PAD
Detach the 2 claws to remove the rear door rear outside handle pad.
69204A
27.REMOVE REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH
Using a T30 "TORX" socket wrench, loosen the screw.
Slide the rear door outside handle frame sub-assembly LH to detach the door handle nut and claw of the rear door outside handle frame sub-assembly LH. Then remove the rear door outside handle frame sub-assembly LH.
68640A
28.REMOVE REAR DOOR CHECK ASSEMBLY LH
Remove the bolt, 2 nuts and rear door check assembly LH.
67872
29.REMOVE REAR DOOR WEATHERSTRIP LH
Using a clip remover, detach the 20 clips to remove the rear door weatherstrip LH.
67003C
30.REMOVE REAR DOOR PANEL CUSHION
Using a clip remover, detach the claw to remove the rear door panel cushion.
75722A
31.REMOVE REAR DOOR BELT MOULDING LH
75762A
32.REMOVE REAR DOOR FRONT WINDOW FRAME MOULDING LH
75924C
33.REMOVE NO. 2 BLACK OUT TAPE LH
75978H
34.REMOVE REAR DOOR LOWER OUTSIDE STRIPE LH
75988E
35.REMOVE REAR DOOR OUTSIDE STRIPE LH
75742
36.REMOVE REAR DOOR OUTSIDE MOULDING LH
75742
37.REMOVE REAR DOOR OUTSIDE MOULDING LH (w/ TOYOTA Parking Assist-sensor System)
75394A
38.REMOVE NO. 3 OUTSIDE MOULDING RETAINER