Home › Vehicle Exterior › DOOR / HATCH › REAR DOOR › 2009.08–2013.08
RM1440E _59 Vehicle Exterior _056168 DOOR / HATCH _0274179 REAR DOOR A

DOOR / HATCH  REAR DOOR  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 75394A 1.INSTALL NO. 3 OUTSIDE MOULDING RETAINER

Hide 75742 2.INSTALL REAR DOOR OUTSIDE MOULDING LH

Hide 75762A 6.INSTALL REAR DOOR FRONT WINDOW FRAME MOULDING LH

Hide 67003C 8.INSTALL REAR DOOR PANEL CUSHION

a.

Attach the claw to install a new door panel cushion.


Hide 67872 9.INSTALL REAR DOOR WEATHERSTRIP LH

a.

Attach the 20 clips to install the rear door weatherstrip.


Hide 68640A 10.INSTALL REAR DOOR CHECK ASSEMBLY LH

a.

Apply MP grease to the sliding areas of the rear door check assembly.


b.
B240713

Install the door check to the door panel with the 2 nuts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


c.

Apply adhesive to the threads of the bolt.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



d.

Install the door check to the body panel with the bolt.

Torque:
27 N*m (275 kgf*cm, 20 ft.*lbf)


Hide 69204A 11.INSTALL REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH

a.

Apply MP grease to the sliding parts of the rear door outside handle frame sub-assembly.


b.
B240748

Attach the door handle nut and claw.


c.

Using a T30 "TORX" socket wrench, install the rear door outside handle frame sub-assembly with the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


Hide 69242G 12.INSTALL REAR DOOR REAR OUTSIDE HANDLE PAD

a.

Attach the 2 claws to install the rear door rear outside handle pad.


Hide 69241G 13.INSTALL REAR DOOR FRONT OUTSIDE HANDLE PAD

a.

Attach the 3 claws to install the rear door front outside handle pad.


Hide 69240 14.INSTALL REAR DOOR OUTSIDE HANDLE ASSEMBLY LH

a.
B240736

Insert the front end of the rear door outside handle assembly into the rear door outside handle frame.

NOTICE:

If the bellcrank lever is not pulled and held when installing the outside handle, the bellcrank lever will interfere with the outside handle and the release plate will be damaged.



b.

Insert the rear end of the rear door outside handle assembly into the rear door outside handle frame. Next, slide the rear door outside handle assembly toward the front of the vehicle to install it.


c.
B240734

Move the lever back in the direction indicated by the arrow in the illustration to lock the door outside handle assembly.


Hide 69227L 15.INSTALL REAR DOOR OUTSIDE HANDLE COVER LH

a.

Attach the claw to install the rear door outside handle cover.


b.

Using a T30 "TORX" socket wrench, install the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


Hide 69780B 16.INSTALL REAR DOOR INSIDE LOCKING CABLE ASSEMBLY LH

a.

Install the rear door inside locking cable assembly.


b.

Attach the 3 claws.


Hide 69740D 17.INSTALL REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH

a.

Install the rear door lock remote control cable assembly.


b.

Attach the claw.


Hide 69060A 18.INSTALL REAR DOOR LOCK ASSEMBLY LH

Hide 85720G 19.INSTALL POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

Hide 69804 20.INSTALL REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY LH

a.

Apply MP grease to the sliding parts of the rear door window regulator assembly.


b.

Install the temporary bolt to the rear door window regulator assembly.


c.
B240723E04
1.729,0.844 1.813,0.844 1.813,0.844 1.885,1.26 true 1.49,0.76 1.719,1 0.229,0.24 10 true *1 2.448,2.167 2.74,2.583 0.292,0.417 10 true (1) 3.063,1.375 3.385,1.635 0.323,0.26 10 true (2) 3.104,1.854 3.344,2.135 0.24,0.281 10 true (3) 1.938,1.052 2.146,1.24 0.208,0.188 10 true (4)

Temporarily install the rear door window regulator assembly.

Text in Illustration
*1 Temporary Bolt


d.

Tighten the temporary bolt and 3 bolts to install the rear door window regulator assembly.

HINT:

Tighten the bolts in the order shown in the illustration.


Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


e.

Connect the connector.


Hide 69975A 21.INSTALL REAR DOOR GLASS CHANNEL FILLER

a.

Apply soapy water to a new rear door glass channel filler.


b.
B234459E02
0.364,0.562 0.557,0.733 0.193,0.171 10 A 2.948,0.55 3.141,0.721 0.193,0.171 10 B 0.616,0.184 0.818,0.345 0.202,0.162 10 *a 2.627,0.172 2.829,0.334 0.202,0.162 10 *b

Install the rear door glass channel filler to the position shown in the illustration.

Text in Illustration
*a Front Side
*b Rear Side

Standard
Area Specified Condition
A 6.8 mm (0.268 in.)
B 6.7 mm (0.264 in.)


Hide 69906B 22.INSTALL REAR DOOR GLASS CHANNEL SUB-ASSEMBLY LH

a.

Apply soapy water to the channel filler side of the rear door glass channel sub-assembly.


b.
B234461E02
0.603,0.185 0.801,0.347 0.198,0.163 10 *a 2.606,0.185 2.803,0.347 0.198,0.163 10 *b 0.363,0.589 0.560,0.751 0.198,0.163 10 A 2.958,0.597 3.155,0.760 0.198,0.163 10 B

Using a plastic-faced hammer, install the rear door glass channel sub-assembly to the position shown in the illustration.

Text in Illustration
*a Front Side
*b Rear Side

Standard
Area Specified Condition
A 6.8 mm (0.268 in.)
B 6.7 mm (0.264 in.)

NOTICE:

To prevent damaging the rear door glass sub-assembly, be careful not to strike the channel with too much force.



Hide 68104 23.INSTALL REAR DOOR GLASS SUB-ASSEMBLY

a.

Temporarily install the regulator switch assembly.


b.

Connect the cable to the negative (-) battery terminal and the rear power window regulator motor connector.


c.
B242781

Operate the regulator switch until the regulator reaches bottom dead center.


d.

Disconnect the power window regulator switch assembly and rear power window regulator motor connector.


e.

Disconnect the cable from the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



f.

Remove the regulator switch assembly.


g.

Install the front side of the glass run.


h.
B242788E02
0.542,1.24 0.792,1.417 0.25,0.177 10 false *a 1.229,1.24 1.479,1.417 0.25,0.177 10 false *b 2.094,1.229 2.271,1.406 0.177,0.177 10 false *c

Apply MP grease to the sliding areas of the glass channel as shown in the illustration.

Text in Illustration
*a 5.0 mm (0.197 in.)
*b 157 mm (6.181 in.)
*c 5.0 mm (0.197 in.)
V100155

MP grease


i.
B240720

Slide the rear door glass sub-assembly as shown in the illustration to install it.


Hide 68189 24.INSTALL REAR DOOR QUARTER WINDOW WEATHERSTRIP LH

a.

Install the rear door quarter window weatherstrip to the rear door quarter window glass.


Hide 68124C 25.INSTALL REAR DOOR QUARTER WINDOW GLASS LH

a.
B240718

Install the rear door quarter window glass together with the rear door quarter window weatherstrip in the direction indicated by the arrow in the illustration.


Hide 67674A 26.INSTALL REAR DOOR FRAME GARNISH LH

a.

Attach the clip to install a new door frame garnish.


Hide 67408F 27.INSTALL REAR DOOR WINDOW REAR LOWER FRAME SUB-ASSEMBLY LH

a.

Insert the rear door window rear lower frame sub-assembly from above.


b.

Install the rear door window rear lower frame sub-assembly to the glass run.


c.
B240716E01
2.366,1.199 2.570,1.411 0.204,0.212 10 *1 2.297,1.318 2.122,1.318 2.122,1.318 1.723,1.85 false

Install the temporary bolt to the rear door window rear lower frame sub-assembly.

Text in Illustration
*1 Temporary Bolt


d.

Install the rear door window rear lower frame sub-assembly to the glass run.


e.

Install the rear door window rear lower frame sub-assembly.


f.

Install the screw.


g.

Install the 2 bolts.

Torque:
6.2 N*m (63 kgf*cm, 55 in.*lbf)


h.

Tighten the temporary bolt to install the rear door window rear guide sub-assembly.

Torque:
6.2 N*m (63 kgf*cm, 55 in.*lbf)


Hide 68152C 28.INSTALL REAR DOOR GLASS RUN LH

a.
B240715

Install the glass run.


Hide 67842E 29.INSTALL REAR DOOR SERVICE HOLE COVER LH

a.

Apply butyl tape to the rear door panel.


b.
B240712E01
0.188,0.208 0.385,0.406 0.198,0.198 10 false *1 3.021,0.198 3.219,0.396 0.198,0.198 10 false *1

Pass the rear door lock remote control cable assembly and rear door inside locking cable assembly through a new rear door service hole cover.


c.

Install the rear door service hole cover according to the reference points on the rear door panel.

Text in Illustration
*1 Reference Point

NOTICE:
·

There should be no wrinkles or folds when installing attaching the service hole cover.

·

After installing the service hole cover, check the seal quality.




d.

Connect the connector.


e.

Attach the 3 clamps to the rear door wire.


Hide 67812C 32.INSTALL REAR DOOR HOLE COVER

a.

Attach the 2 claws to install the rear door hole cover.


Hide 84810D 33.INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY

Hide 68174A 34.INSTALL REAR DOOR INNER GLASS WEATHERSTRIP LH

a.
B240749

Attach the 3 claws to install the rear door inner glass weatherstrip as shown in the illustration.


Hide 67604 35.INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY LH

a.
B240750

Install the clamp to the door panel.


b.
B242790

Connect the rear door lock remote control cable assembly and rear door inside locking cable assembly.


c.
B242772

Connect the connector.


d.
B240707

Attach the rear door trim board sub-assembly to the 4 claws of the rear door inner glass weatherstrip as shown in the illustration.


e.

Attach the 9 clips to install the rear door trim board sub-assembly.


f.

Install the 3 screws.


g.

Attach the 4 claws to install the 2 hole covers.


Hide 69278C 36.INSTALL REAR DOOR INSIDE HANDLE BEZEL LH

a.

Attach the 3 claws to install the door inside handle bezel.


Hide 37.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 38.INITIALIZE POWER WINDOW CONTROL SYSTEM

a.

Initialize the power window control system (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION).