Home › Vehicle Exterior › DOOR / HATCH › REAR DOOR › from 2013.08
RM1440E _59 Vehicle Exterior _056168 DOOR / HATCH _0274179 REAR DOOR A

DOOR / HATCH  REAR DOOR  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for both the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 75394A 1.INSTALL NO. 3 OUTSIDE MOULDING RETAINER

Hide 75742 2.INSTALL REAR DOOR OUTSIDE MOULDING LH

Hide 75742 3.INSTALL REAR DOOR OUTSIDE MOULDING LH (w/ TOYOTA Parking Assist-sensor System)

Hide 75762A 7.INSTALL REAR DOOR FRONT WINDOW FRAME MOULDING LH

Hide 67003C 9.INSTALL REAR DOOR PANEL CUSHION

a.
B240622

Attach the claw to install a new rear door panel cushion.


Hide 67872 10.INSTALL REAR DOOR WEATHERSTRIP LH

a.
B240714

Attach the 20 clips to install the rear door weatherstrip LH.


Hide 68640A 11.INSTALL REAR DOOR CHECK ASSEMBLY LH

a.

Apply MP grease to the sliding areas of the rear door check assembly LH.


b.
A057108E60
2.156,0.26 2.031,0.26 2.031,0.26 1.75,1.292 false 2.198,0.156 2.417,0.354 0.219,0.198 10 false *1

Apply a few drops of adhesive to 2 or 3 threads of the bolt.

Text in Illustration
*1 Adhesive

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

Install the bolt within 3 minutes of applying adhesive.



c.
B240713

Install the rear door check assembly LH to the rear door panel with the 2 nuts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


d.

Install the rear door check assembly LH to the vehicle body with the bolt.

Torque:
27 N*m (275 kgf*cm, 20 ft.*lbf)


Hide 69204A 12.INSTALL REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH

a.

Apply MP grease to the sliding parts of the rear door outside handle frame sub-assembly LH.


b.
B240748

Attach the door handle nut and claw.


c.

Using a T30 "TORX" socket wrench, install the rear door outside handle frame sub-assembly LH with the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


Hide 69242G 13.INSTALL REAR DOOR REAR OUTSIDE HANDLE PAD

a.
B240738

Attach the 2 claws to install the rear door rear outside handle pad.


Hide 69241G 14.INSTALL REAR DOOR FRONT OUTSIDE HANDLE PAD

a.
B240737

Attach the 3 claws to install the rear door front outside handle pad.


Hide 69240 15.INSTALL REAR DOOR OUTSIDE HANDLE ASSEMBLY LH

a.
B240736

Insert the front end of the rear door outside handle assembly LH into the rear door outside handle frame sub-assembly LH.

NOTICE:

If the bellcrank lever is not pulled and held when installing the rear door outside handle assembly LH, the bellcrank lever will interfere with the rear door outside handle assembly LH and the release plate will be damaged.



b.

Insert the rear end of the rear door outside handle assembly LH into the rear door outside handle frame sub-assembly. Next, slide the rear door outside handle assembly LH toward the front of the vehicle to install it.


c.
B240734

Move the lever back in the direction indicated by the arrow in the illustration to lock the rear door outside handle assembly LH.


Hide 69227L 16.INSTALL REAR DOOR OUTSIDE HANDLE COVER LH

a.
B240732

Attach the claw to install the rear door outside handle cover LH.


b.

Using a T30 "TORX" socket wrench, install the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


Hide 69780B 17.INSTALL REAR DOOR INSIDE LOCKING CABLE ASSEMBLY LH

a.
B240731

Install the rear door inside locking cable assembly LH to the rear door lock assembly LH.


b.
B240730

Attach the 3 claws to close the cover.


Hide 69740D 18.INSTALL REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH

a.
B240729

Install the rear door lock remote control cable assembly LH to the rear door lock assembly LH.


b.
B240728

Attach the claw to close the cover.


Hide 69060A 19.INSTALL REAR DOOR LOCK ASSEMBLY LH

Hide 85720G 20.INSTALL REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

Hide 69804 21.INSTALL REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY LH

a.

Apply MP grease to the sliding parts of the rear door window regulator sub-assembly LH.


b.

Install the temporary bolt to the rear door window regulator sub-assembly LH.


c.
B240723E04
1.729,0.844 1.813,0.844 1.813,0.844 1.885,1.26 true 1.49,0.76 1.719,1 0.229,0.24 10 true *1 2.448,2.167 2.74,2.583 0.292,0.417 10 true (1) 3.063,1.375 3.385,1.635 0.323,0.26 10 true (2) 3.104,1.854 3.344,2.135 0.24,0.281 10 true (3) 1.938,1.052 2.146,1.24 0.208,0.188 10 true (4)

Temporarily install the rear door window regulator sub-assembly LH.

Text in Illustration
*1 Temporary Bolt


d.

Tighten the temporary bolt and 3 bolts to install the rear door window regulator sub-assembly LH.

HINT:

Tighten the bolts in the order shown in the illustration.


Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


e.

Connect the connector.


Hide 69975A 22.INSTALL REAR DOOR GLASS CHANNEL FILLER

a.

Apply soapy water to a new rear door glass channel filler.


b.
B234459E02
0.364,0.562 0.557,0.733 0.193,0.171 10 A 2.948,0.55 3.141,0.721 0.193,0.171 10 B 0.616,0.184 0.818,0.345 0.202,0.162 10 *a 2.627,0.172 2.829,0.334 0.202,0.162 10 *b

Install the rear door glass channel filler to the position shown in the illustration.

Standard
Area Specified Condition
A 6.8 mm (0.268 in.)
B 6.7 mm (0.264 in.)

Text in Illustration
*a Front Side
*b Rear Side


Hide 69906B 23.INSTALL REAR DOOR GLASS CHANNEL SUB-ASSEMBLY LH

a.

Apply soapy water to the rear door glass channel filler side of the rear door glass channel sub-assembly LH.


b.
B234461E02
0.603,0.185 0.801,0.347 0.198,0.163 10 *a 2.606,0.185 2.803,0.347 0.198,0.163 10 *b 0.363,0.589 0.560,0.751 0.198,0.163 10 A 2.958,0.597 3.155,0.760 0.198,0.163 10 B

Using a plastic-faced hammer, install the rear door glass channel sub-assembly LH to the position shown in the illustration.

Standard
Area Specified Condition
A 6.8 mm (0.268 in.)
B 6.7 mm (0.264 in.)

Text in Illustration
*a Front Side
*b Rear Side

NOTICE:

To prevent damaging the rear door glass sub-assembly LH, be careful not to strike the channel with too much force.



Hide 68104 24.INSTALL REAR DOOR GLASS SUB-ASSEMBLY LH

a.

Connect the rear power window regulator switch assembly.


b.

Connect the cable to the negative (-) battery terminal.


c.
B242781

Move the arm of the rear door window regulator sub-assembly LH so that the roller on the arm can be seen through the service hole.


d.

Disconnect the cable from the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



e.

Disconnect the rear power window regulator switch assembly.


f.

Install the front side of the rear door glass run LH.


g.
B242788E01
0.54,1.193 0.792,1.375 0.252,0.182 10 *a 1.229,1.193 1.481,1.375 0.252,0.182 10 *b 2.092,1.193 2.274,1.375 0.182,0.182 10 *c

Apply MP grease to the sliding areas of the rear door glass channel sub-assembly LH as shown in the illustration.

Text in Illustration
*a 5.0 mm (0.197 in.)
*b 157 mm (6.181 in.)
*c 5.0 mm (0.197 in.)
V100155

MP grease


h.
B240720

Slide the rear door glass sub-assembly LH as shown in the illustration to install it.


Hide 68189 25.INSTALL REAR DOOR QUARTER WINDOW WEATHERSTRIP LH

a.

Install the rear door quarter window weatherstrip LH to the rear door quarter window glass LH.


Hide 68124C 26.INSTALL REAR DOOR QUARTER WINDOW GLASS LH

a.
B240718

Install the rear door quarter window glass LH together with the rear door quarter window weatherstrip LH as shown in the illustration.


Hide 67408F 27.INSTALL REAR DOOR WINDOW REAR LOWER FRAME SUB-ASSEMBLY LH

a.
B240716E01
2.366,1.199 2.570,1.411 0.204,0.212 10 *1 2.297,1.318 2.122,1.318 2.122,1.318 1.723,1.85 false

Install the temporary bolt to the rear door window rear lower frame sub-assembly LH.

Text in Illustration
*1 Temporary Bolt


b.

Temporarily install the rear door window rear lower frame sub-assembly LH to the rear door panel.


c.

Install the screw.


d.

Install the 2 bolts.

Torque:
6.2 N*m (63 kgf*cm, 55 in.*lbf)


e.

Tighten the temporary bolt to install the rear door window rear lower frame sub-assembly LH.

Torque:
6.2 N*m (63 kgf*cm, 55 in.*lbf)


Hide 68152C 28.INSTALL REAR DOOR GLASS RUN LH

a.
B240715

Install the rear door glass run LH.


Hide 67674A 29.INSTALL REAR DOOR FRAME GARNISH LH

a.
B240621

Attach the clip to install a new rear door frame garnish LH.


Hide 67842E 30.INSTALL REAR DOOR SERVICE HOLE COVER LH

a.

Apply a new butyl tape to the rear door panel.


b.
B240712E01
0.188,0.208 0.385,0.406 0.198,0.198 10 false *1 3.021,0.198 3.219,0.396 0.198,0.198 10 false *1

Pass the rear door lock remote control cable assembly LH and rear door inside locking cable assembly LH through a new rear door service hole cover LH.


c.

Install the rear door service hole cover LH according to the reference points on the rear door panel.

Text in Illustration
*1 Reference Point

NOTICE:

Securely install the rear door service hole cover LH preventing wrinkles and air bubbles.



d.

Connect the connector.


e.

Attach the 3 clamps and rear door wire.


Hide 81090 32.INSTALL NO. 1 INTERIOR ILLUMINATION LIGHT ASSEMBLY (w/ TOYOTA Parking Assist-sensor System)

a.

Connect the connector.


b.

Attach the claw to install the light.


Hide 84810D 34.INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY

Hide 68174A 35.INSTALL REAR DOOR INNER GLASS WEATHERSTRIP LH

a.
B240749

Attach the 3 claws to install the rear door inner glass weatherstrip LH as shown in the illustration.


Hide 67604 36.INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY LH

a.
B240750

Attach the claw to install the clamp.


b.
B242790

Connect the rear door lock remote control cable assembly LH and rear door inside locking cable assembly LH as shown in the illustration.


c.
B242772

Connect the connector.


d.
B357471E01
1.339,4.279 1.494,4.424 0.155,0.145 10 *1 2.008,4.247 2.163,4.391 0.155,0.145 10 *1 1.12,4.067 1.318,4.271 false 2.466,4.056 2.193,4.26 false

Attach the rear door trim board sub-assembly LH to the 4 claws of the rear door inner glass weatherstrip LH as shown in the illustration.


e.

Attach the reference boss.

Text in Illustration
*1 Reference Boss


f.
B240704

Attach the 9 clips to install the rear door trim board sub-assembly LH.


g.

Install the 3 screws.


h.
B357479

Attach the 4 claws to install the 2 door armrest caps.


Hide 69278C 37.INSTALL REAR DOOR INSIDE HANDLE BEZEL LH

a.
B357472

Attach the 3 claws to install the rear door inside handle bezel LH.


Hide 38.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 39.INITIALIZE POWER WINDOW CONTROL SYSTEM