Home › Vehicle Exterior › DOOR / HATCH › BACK DOOR › 2009.08–2012.08
RM1440E _59 Vehicle Exterior _056168 DOOR / HATCH _0274180 BACK DOOR A

DOOR / HATCH  BACK DOOR  DISASSEMBLY  


PROCEDURE

Hide 1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 74811G 2.REMOVE DOOR PULL HANDLE

a.
B240249

Using moulding remover D, detach the 4 claws and remove the back door pull handle.

HINT:

Use the same procedure for all back door pull handles.



Hide 69308 3.REMOVE BACK DOOR LOCK PROTECTOR SUB-ASSEMBLY

a.
B240228

Detach the 2 claws and remove the back door lock protector.


Hide 64780A 4.REMOVE BACK DOOR TRIM PANEL ASSEMBLY

a.
B240234

Detach the 12 clips by pulling the back door trim panel assembly.


Hide 68291 5.REMOVE BACK DOOR GLASS WEATHERSTRIP

a.
B240245

Raise the 9 claws of the back door glass weatherstrip and remove the back door glass weatherstrip from the back door trim panel assembly1 as shown in the illustration.


Hide 86160Y 6.REMOVE REAR NO. 2 SPEAKER ASSEMBLY

Hide 89222A 7.REMOVE MULTIPLEX NETWORK DOOR ECU

a.
B242092

Disconnect the 3 connectors to detach the 2 clamps.


b.
B242093

Remove the 3 screws.


c.
B242094

Using a clip remover, detach the 2 clips and remove the multiplex network door ECU.


Hide 67848C 8.REMOVE NO. 2 BACK DOOR SERVICE HOLE COVER

a.
B240216

Remove the back door service hole cover LH.

NOTICE:

Remove any remaining tape on the back door side.



Hide 67848 9.REMOVE BACK DOOR SERVICE HOLE COVER LH

a.
B240218

Detach the clamp and move the wire harness out of the way.


b.

Remove the 5 screws.


c.

Using a clip remover, detach the 2 clips and remove the service hole cover.


Hide 67847 10.REMOVE BACK DOOR SERVICE HOLE COVER RH

a.
B240219

Detach the clamp and move the wire harness out of the way.


b.

Remove the 5 screws.


c.

Using a clip remover, detach the 2 clips and remove the service hole cover.


Hide 76893 13.REMOVE REAR NO. 1 SPOILER COVER

Hide 76085 14.REMOVE REAR SPOILER SUB-ASSEMBLY

Hide 85120R 16.REMOVE REAR WIPER MOTOR AND BRACKET ASSEMBLY

Hide 67381A 17.REMOVE NO. 1 BACK WINDOW WIPER MOTOR BRACKET

a.
E199085

Remove the 3 bolts.


b.

Using a clip remover, detach the 2 clips and remove the No. 1 back window wiper motor bracket.


Hide 85293A 19.REMOVE REAR WIPER STOPPER

a.
E199086E01
1.378,2.208 1.638,2.452 0.259,0.244 10 *1 1.571,2.3 1.726,2.3 1.726,2.3 2.152,2.805 false

Insert a screwdriver into the rear spoiler service hole, detach the claw and remove the wiper step.

Text in Illustration
*1 Protective Tape


Hide 68275 20.REMOVE BACK DOOR GLASS RUN

a.
B240220

Remove the back door glass run.


Hide 68131 21.REMOVE BACK DOOR GLASS

a.

Temporarily connect the multiplex network body ECU connectors.


b.
B240221

Remove the hole plug.


c.

Connect the cable to the negative (-) battery terminal.


d.
B240222

Move the back door glass until the 4 bolts can be seen through the service holes.


e.

Disconnect the cable from the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



f.

Disconnect the multiplex network body ECU connectors.


g.
B240223

Remove the bolt and disconnect the 2 defogger connectors.


h.
B240222

Remove the 4 bolts.


i.
B240225E02
1.979,1.323 2.188,1.521 0.208,0.198 10 false (1) 2.458,0.375 2.667,0.573 0.208,0.198 10 false (2)

Remove the door glass as shown in the illustration.


j.

Disconnect the rear window connector.


k.

Disconnect the multiplex network door ECU connector.


Hide 68290A 22.REMOVE OUTER BACK DOOR GLASS WEATHERSTRIP ASSEMBLY

Hide 69350 23.REMOVE BACK DOOR LOCK ASSEMBLY

Hide 69807 24.REMOVE BACK DOOR POWER WINDOW REGULATOR SUB-ASSEMBLY

a.
B242097

Disconnect the window regulator connector.


b.
B240229

Remove the 5 bolts, nut and window regulator.

HINT:

Remove the power window regulator through the service hole.



Hide 85720E 25.REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

Hide 69055B 26.REMOVE BACK DOOR LOCK CYLINDER

a.
B240231

Disconnect the connector.


b.

Remove the 2 nuts and lock cylinder.

HINT:

Remove the back door lock cylinder assembly through the service hole.



Hide 76827A 27.REMOVE NO. 2 BACK DOOR GARNISH RETAINER (w/o Rear View Monitor System)

a.
B240235

Detach the 2 claws and remove the No. 2 back door garnish retainer.


Hide 86790D 29.REMOVE REAR TELEVISION CAMERA ASSEMBLY (w/ Rear View Monitor System)

Hide 84840G 30.REMOVE BACK DOOR OPENER SWITCH ASSEMBLY

a.
B240243

Disconnect the connector.


b.

Detach the guide.


c.

Remove the 2 screws and back door opener switch assembly.


Hide 81270 31.REMOVE LICENSE PLATE LIGHT ASSEMBLY

Hide 67281F 32.REMOVE BACK DOOR LOWER STOPPER

a.
B240241

Remove the bolt.


b.

Detach the guide and back door lower stopper.

HINT:

Use the same procedure as for the LH side.



Hide 67005B 33.REMOVE BACK DOOR PANEL CUSHION

a.
B240230

Remove the 2 back door panel cushions.


Hide 68908 34.REMOVE BACK DOOR DAMPER STAY SUB-ASSEMBLY LH

Hide 68907 35.REMOVE BACK DOOR DAMPER STAY SUB-ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 68961 36.REMOVE BACK DOOR STAY BOLT (for LH Side)

Hide 68961 37.REMOVE BACK DOOR STAY BOLT (for RH Side)

HINT:

Use the same procedure as for the LH side.


Hide 68946 38.REMOVE BACK DOOR UPPER DAMPER STAY BRACKET LH

Hide 68945 39.REMOVE BACK DOOR UPPER DAMPER STAY BRACKET RH

HINT:

Use the same procedure as for the LH side.