Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM › from 2016.12
RM1440E _57 Power Source / Network _056154 NETWORKING _0274052 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2325  LIN Communication Bus Malfunction  


DESCRIPTION

The main body ECU (multiplex network body ECU) intermittently monitors the LIN communication bus between the components related to the doors and sliding roof ECU (sliding roof drive gear sub-assembly)*. DTC B2325 is stored when a malfunction in the LIN communication bus between the components related to the doors and sliding roof ECU (sliding roof drive gear sub-assembly)* is detected consecutively 3 times.

*: w/ Sliding Roof System


DTC Code DTC Detection Condition Trouble Area
B2325 The main body ECU (multiplex network body ECU) detects a malfunction in the LIN communication bus between components related to the doors and sliding roof ECU (sliding roof drive gear sub-assembly)* consecutively 3 times.
·

Multiplex network master switch assembly

·

Front power window regulator motor assembly LH

·

Front power window regulator motor assembly RH

·

Rear power window regulator motor assembly LH

·

Rear power window regulator motor assembly RH

·

Multiplex network door ECU (back door P/W)

·

Sliding roof ECU (sliding roof drive gear sub-assembly)*

·

Driver side junction block assembly

·

Main body ECU (multiplex network body ECU)

·

Harness or connector



*: w/ Sliding Roof System


WIRING DIAGRAM

B467033E01
0.24,1.667 1.875,2.271 1.635,0.604 10 false Main Body ECU (Multiplex Network Body ECU) 0.25,1.479 0.563,1.719 0.313,0.24 10 false A 1.448,0.698 1.927,0.969 0.479,0.271 10 false LIN2 1.823,0.563 2.229,0.802 0.406,0.24 10 false 16 1.948,1.26 3.208,1.854 1.26,0.594 10 false Driver Side Junction Block Assembly 1.938,1.073 2.25,1.313 0.313,0.24 10 false 2B 5.198,1.667 6.813,2.281 1.615,0.615 10 false Multiplex Network Master Switch Assembly 1.073,3.646 3.083,4.042 2.01,0.396 10 false Sliding Roof ECU (Sliding Roof Drive Gear Sub-assembly)* 4.427,5.552 6.406,6.229 1.979,0.677 10 false Front Power Window Regulator Motor Assembly RH 5.438,0.698 5.99,1 0.552,0.302 10 false LIN1 5.438,1 5.979,1.292 0.542,0.292 10 false LIN2 5.156,0.552 5.573,0.813 0.417,0.26 10 false 17 5.156,0.865 5.448,1.135 0.292,0.271 10 false 16 5.188,1.5 5.479,1.75 0.292,0.25 10 false h1 4.875,2.917 5.448,3.188 0.573,0.271 10 false LIN 4.656,2.76 4.865,3.031 0.208,0.271 10 false 9 4.49,3.604 6.427,4.375 1.938,0.771 10 false Front Power Window Regulator Motor Assembly LH 4.5,3.417 4.813,3.688 0.313,0.271 10 false I2 4.427,5.365 4.771,5.646 0.344,0.281 10 false H2 4.896,4.885 5.344,5.177 0.448,0.292 10 false LIN 4.646,4.698 4.885,4.969 0.24,0.271 10 false 9 1.927,2.917 2.583,3.219 0.656,0.302 10 false MPX1 1.073,3.458 1.552,3.74 0.479,0.281 10 false S10 2.406,2.74 2.771,3.01 0.365,0.271 10 false 11 1.927,4.875 2.615,5.135 0.688,0.26 10 false MPX1 2.427,4.698 2.781,4.979 0.354,0.281 10 false 16 1.063,5.583 2.542,6.25 1.479,0.667 10 false Multiplex Network Door ECU (Back Door P/W) 1.073,5.385 1.479,5.677 0.406,0.292 10 false V2 2.448,8.375 4.281,8.667 1.833,0.292 10 false *: w/ Sliding Roof System 2.427,6.635 2.677,6.906 0.25,0.271 10 false 9 2.083,6.802 2.604,7.115 0.521,0.313 10 false LIN 0.865,7.292 1.219,7.563 0.354,0.271 10 false K2 0.854,7.49 2.75,8.146 1.896,0.656 10 false Rear Power Window Regulator Motor Assembly LH 4.656,6.635 4.917,6.917 0.26,0.281 10 false 9 4.885,6.823 5.365,7.115 0.479,0.292 10 false LIN 4.458,7.302 4.823,7.552 0.365,0.25 10 false J2 4.448,7.49 6.354,8.156 1.906,0.667 10 false Rear Power Window Regulator Motor Assembly RH 0.74,8.375 3.896,8.708 3.156,0.333 10 false : LIN Communication Line 3.198,0.542 3.51,0.781 0.313,0.24 10 false 11

CAUTION / NOTICE / HINT

NOTICE:
·

When using the intelligent tester with the ignition switch off to troubleshoot:

Connect the intelligent tester to the vehicle and turn a courtesy light switch on and off at 1.5 second intervals until communication between the intelligent tester and vehicle begins.

·

Inspect the fuses and bulbs for circuits related to this system before performing the following inspection procedure.



HINT:

When DTC B2325 and a LIN communication stop DTC are output simultaneously, first perform troubleshooting for the LIN communication stop DTC. Then perform troubleshooting for DTC B2325.


PROCEDURE

1.CLEAR DTC

NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B2325 is not output.




OK

NG

3.CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY
3.CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY
a.

Remove the main body ECU (multiplex network body ECU) from the driver side junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-16 (LIN2) - 2B-11 Always Below 1 Ω
A-16 (LIN2) or 2B-11 - Body ground Always 10 kΩ or higher




OK

4.CLEAR DTC

NG

REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY

4.CLEAR DTC
a.

Install the main body ECU (multiplex network body ECU) to the driver side junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>INSTALLATION).


b.

Disconnect the I2 front power window regulator motor assembly LH connector.




NEXT

5.CHECK FOR DTC
5.CHECK FOR DTC
a.

Check for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2325 is output A
DTC B2325 is not output B



A

6.CLEAR DTC

B

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

6.CLEAR DTC
a.

Connect the I2 front power window regulator motor assembly LH connector.


b.

Disconnect the h1 multiplex network master switch assembly connector.




NEXT

7.CHECK FOR DTC
7.CHECK FOR DTC
a.

Check for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2325 is output A
DTC B2325 is not output B



A

8.CLEAR DTC

B

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

8.CLEAR DTC
a.

Connect the h1 multiplex network master switch assembly connector.


b.

Disconnect the H2 front power window regulator motor assembly RH connector.




NEXT

9.CHECK FOR DTC
9.CHECK FOR DTC
a.

Check for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2325 is output A
DTC B2325 is not output B



A

10.CLEAR DTC

B

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

10.CLEAR DTC
a.

Connect the H2 front power window regulator motor assembly RH connector.


b.

Disconnect the J2 rear power window regulator motor assembly RH connector.




NEXT

11.CHECK FOR DTC
11.CHECK FOR DTC
a.

Check for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2325 is output A
DTC B2325 is not output B



A

12.CLEAR DTC

B

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

12.CLEAR DTC
a.

Connect the J2 rear power window regulator motor assembly RH connector.


b.

Disconnect the K2 rear power window regulator motor assembly LH connector.




NEXT

13.CHECK FOR DTC
13.CHECK FOR DTC
a.

Check for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2325 is output A
DTC B2325 is not output B



A

14.CLEAR DTC

B

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

14.CLEAR DTC
a.

Connect the K2 rear power window regulator motor assembly LH connector.


b.

Disconnect the V2 multiplex network door ECU (back door P/W) connector.




NEXT

15.CHECK FOR DTC
15.CHECK FOR DTC
a.

Check for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2325 is output (w/ Sliding Roof System) A
DTC B2325 is output (w/o Sliding Roof System) B
DTC B2325 is not output C



A

16.CLEAR DTC

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

REPLACE MULTIPLEX NETWORK DOOR ECU (BACK DOOR P/W)

16.CLEAR DTC
a.

Connect the V2 multiplex network door ECU (back door P/W) connector


b.

Disconnect the S10 sliding roof ECU (sliding roof drive gear sub-assembly) connector.




NEXT

17.CHECK FOR DTC
17.CHECK FOR DTC
a.

Check for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2325 is output A
DTC B2325 is not output B



A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY)