Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART KEY SYSTEM (for Entry Function)

SMART KEY SYSTEM (for Entry Function) > Front Passenger Side Door Entry Lock and Unlock Functions do not Operate

for Preparation Click here


DESCRIPTION

When the front passenger side door entry lock and unlock functions do not operate, one of the following may be malfunctioning: 1) the power door lock control system, 2) the front door outside handle (for front passenger side), or 3) the certification ECU.

WIRING DIAGRAM


B242660E02


INSPECTION PROCEDURE

NOTICE:
  1. The smart key system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the smart key system (for Entry Function) after confirming that the communication systems are functioning properly.
  2. When using the Techstream with the engine switch off to troubleshoot: Connect the Techstream to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the Techstream and vehicle begins.
  3. Check that there are no electrical key transmitters in the vehicle.
  4. Before performing the inspection, check that DTC B1242 (wireless door lock control) is not output (Click here).
  5. When checking the entry lock operation multiple times, the lock operation may be limited to 2 consecutive operations depending on the settings. In order to perform the entry lock operation 3 or more times, an unlock operation must be performed once (any type of unlock operation is sufficient). However, only consecutive entry lock operations are limited. Using the wireless lock or other types of lock operations, it is possible to perform consecutive lock operations without this limitation.
  6. Before replacing the certification ECU, refer to the engine immobiliser system (w/ Smart Key System) (Click here).

1.CHECK POWER DOOR LOCK OPERATION
  1. When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation (Click here).

    OK:
    Door locks operate normally.



NG
GO TO POWER DOOR LOCK CONTROL SYSTEM (Click here)
OK


2.CHECK WAVE ENVIRONMENT
  1. Bring the electrical key transmitter approximately 0.3 m (0.984 ft.) from the door outside handle (for front passenger side) and perform a front passenger side door entry lock and unlock operation check (Click here).

    NOTICE:
    If the key is brought within 0.2 m (0.656 ft.) of the door handle, communication is not possible.

    HINT:
    1. When the electrical key transmitter is brought near the front passenger side door outside handle, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.
    2. If the operation check is normal, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

    OK:
    Entry function operates normally.



NG
Go to step 3
OK

AFFECTED BY WAVE INTERFERENCE 

3.READ VALUE USING TECHSTREAM (DOOR LOCK POSITION SWITCH)
  1. Connect the Techstream to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Main Body / Data List.

  1. Read the Data List according to the display on the Techstream.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    FR Door Lock Pos
    Front RH side door lock position switch signal / UNLOCK or LOCK
    UNLOCK: Front RH side door unlocked
    LOCK: Front RH side door locked
    -

    OK:
    On the Techstream screen, the display changes between LOCK and UNLOCK as shown in the chart above.



NG
GO TO POWER DOOR LOCK CONTROL SYSTEM (Proceed to Only Passenger Door Lock/Unlock Functions do not Operate) (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (FRONT DOOR OUTSIDE HANDLE - CERTIFICATION ECU)
  1. Disconnect the L1 handle connector.

  1. Disconnect the F79 ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L1-3 (ANT2) - F79-6 (CG2B)
    Always
    Below 1 Ω
    L1-6 (ANT1) - F79-5 (CLG2)
    Always
    Below 1 Ω
    L1-5 (B) - F79-33 (POS2)
    Always
    Below 1 Ω
    L1-2 (GND) - Body ground
    Always
    Below 1 Ω
    F79-6 (CG2B) - Body ground
    Always
    10 kΩ or higher
    F79-5 (CLG2) - Body ground
    Always
    10 kΩ or higher
    F79-33 (POS2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK CERTIFICATION ECU


    B199753E36
  1. Disconnect the L1 handle connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    L1-3 (ANT2) - L1-6 (ANT1)
    Engine switch off, all doors closed, key not in cabin and transmitter lock switch not pressed → pressed
    No pulse generation → Pulse generation
    L1-5 (B) - Body ground
    Engine switch off → on (IG)
    9 to 14 V → Below 2 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Front Door Outside Handle Assembly [for Front Passenger Side])



NG
REPLACE CERTIFICATION ECU (Click here)
OK


6.REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER SIDE)
  1. Temporarily replace the front door outside handle assembly (for front passenger side) with a new or normally functioning one (Click here).


NEXT


7.CHECK FRONT DOOR OUTSIDE HANDLE ASSEMBLY (OPERATION)
  1. Check that the entry functions operate normally (Click here).

    OK:
    Entry functions operate normally.



NG
REPLACE CERTIFICATION ECU (Click here)
OK

END (FRONT DOOR OUTSIDE HANDLE ASSEMBLY IS DEFECTIVE)