Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM

POWER WINDOW CONTROL SYSTEM > Front Passenger Side Power Window Auto Up / Down Function does not Operate with Front Passenger Side Power Window Switch

for Preparation Click here


DESCRIPTION

If the auto up/down function does not operate, the cause may be one or more of the following:
  1. The ECU in the power window regulator motor determines that the power window regulator motor has not been initialized.
  2. The power window regulator switch has a malfunction.
  3. The Hall IC in the power window regulator motor has a malfunction.
  4. There is an open or short in the wiring between the power window regulator switch and power window regulator motor.

WIRING DIAGRAM


B240839E01


INSPECTION PROCEDURE

HINT:
Since the power window control system has functions that use LIN communication, first confirm that there is no malfunction in the communication system by inspecting the LIN communication functions in accordance with the "How to Proceed with Troubleshooting" procedures. Then, conduct the following inspection procedure.

1.CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).
    Result  
    Result
    Proceed to
    DTC is not output
    A
    DTC B2311 is output
    B
    DTC B2312 is output
    C
    DTC B2313 is output
    D



B
GO TO DTC B2311 (Click here)

C
GO TO DTC B2312 (Click here)

D
GO TO DTC B2313 (Click here)
A


2.CHECK MANUAL UP/DOWN FUNCTION (POWER WINDOW REGULATOR SWITCH)
  1. Check that the manual up/down function using the front power window regulator switch can operate the front power window (Click here).

    OK:
    Front passenger side door power window moves.



NG
GO TO "Front Passenger Side Power Window does not Operate with Front Passenger Side Power Window Switch" (Click here)
OK


3.READ VALUE USING TECHSTREAM (POWER WINDOW REGULATOR SWITCH)
  1. Use the Data List to check if the front power window regulator is functioning properly (Click here).

    P-Door Motor 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    P Door P/W Auto SW
    Front passenger side power window auto up/down signal / ON or OFF
    ON: Front passenger side power window auto up/down switch operated
    OFF: Front passenger side power window regulator switch not operated
    -

    OK:
    On tester screen, item changes between ON and OFF according to above chart.



NG
Go to step 4
OK

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (Click here)  

4.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY


    B215963E18
  1. Remove the power window regulator switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    8 (AUTO) - 1 (GND)
    Auto up/down operation
    Below 1 Ω
    8 (AUTO) - 1 (GND)
    Not operated
    10 kΩ or higher



NG
REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH - FRONT POWER WINDOW REGULATOR MOTOR RH AND BODY GROUND)
  1. Disconnect the g1 power window regulator switch connector.

  1. Disconnect the H2 power window regulator motor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    g1-8 (AUTO) - H2-4 (AUTO)
    Always
    Below 1 Ω
    g1-1 (GND) - Body ground
    Always
    Below 1 Ω
    g1-8 (AUTO) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (Click here)