Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM

POWER WINDOW CONTROL SYSTEM > Auto Up / Down Function does not Operate

for Preparation Click here


DESCRIPTION

If the auto up/down function does not operate, the cause may be one or more of the following:
  1. The ECU in the back door power window regulator motor determines that the back door power window regulator motor has not been initialized.
  2. The rear back door power window regulator switch has a malfunction.
  3. The Hall IC in the back door power window regulator motor has a malfunction.
  4. There is an open or short in the wiring between the back door power window regulator switch and back door power window regulator motor.

WIRING DIAGRAM


B245634E01


INSPECTION PROCEDURE

HINT:
Since the power window control system has functions that use LIN communication, first confirm that there is no malfunction in the communication system by inspecting the LIN communication functions in accordance with the "How to Proceed with Troubleshooting" procedures. Then, conduct the following inspection procedure.

1.CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC B2311 is output
    B
    DTC B2312 is output
    C
    DTC B2313 is output
    D
    LIN communication system DTCs are output
    E



B
GO TO DTC B2311 (Click here)

C
GO TO DTC B2312 (Click here)

D
GO TO DTC B2313 (Click here)

E
GO TO LIN COMMUNICATION SYSTEM (Click here)
A


2.CHECK MANUAL UP/DOWN FUNCTION (BACK DOOR POWER WINDOW REGULATOR SWITCH ASSEMBLY)
  1. Check that the manual up/down function using the back door power window regulator switch can operate the multiplex network door ECU (Click here).

    OK:
    Manual up/down function operates.



NG
GO TO "Manual Up / Down Function does not Operate on Back Door Only" (Click here)
OK


3.READ VALUE USING TECHSTREAM (BACK DOOR POWER WINDOW REGULATOR SWITCH)
  1. Use the Data List to check if the back door power window regulator switch is functioning properly (Click here).

    Back Door P/W 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Inside Back Door P/W Auto SW
    Back door power window regulator switch auto up/down signal / ON or OFF
    ON: Back door power window regulator auto up/down switch operated
    OFF: Back door power window regulator switch not operated
    -

    OK:
    On tester screen, item changes between ON and OFF according to above chart.



NG
Go to step 6
OK


4.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK DOOR ECU - BACK DOOR POWER WINDOW REGULATOR MOTOR ASSEMBLY)
  1. Disconnect the W9 back door power window regulator motor connector.

  1. Disconnect the W10 multiplex network door ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    W9-4 (AUTO) - W10-12 (AUT2)
    Always
    Below 1 Ω
    W9-1 (GND) - W10-1 (E4)
    Always
    Below 1 Ω
    W9-4 (AUTO) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK MULTIPLEX NETWORK DOOR ECU (BACK DOOR P/W)


  1. Reconnect the multiplex network door ECU.


    B245638E01

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Tool Setting
    Switch Condition
    Specified Condition
    W10-12 (AUT2) - W10-1 (E4)
    2 V/DIV., 100 ms/DIV.
    Ignition switch ON, back door power window auto up or auto down function operating
    Pulse generation (See waveform 1)



NG
REPLACE MULTIPLEX NETWORK DOOR ECU (BACK DOOR P/W) (Click here)
OK

REPLACE BACK DOOR POWER WINDOW REGULATOR MOTOR ASSEMBLY (Click here)  

6.INSPECT BACK DOOR POWER WINDOW REGULATOR SWITCH ASSEMBLY


    B215963E15
  1. Remove the back door power window regulator switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    8 (AUTO) - 1 (E)
    Auto up/down operation
    Below 1 Ω
    8 (AUTO) - 1 (E)
    Not operated
    10 kΩ or higher



NG
REPLACE BACK DOOR POWER WINDOW REGULATOR SWITCH ASSEMBLY (Click here)
OK


7.CHECK HARNESS AND CONNECTOR (BACK DOOR POWER WINDOW REGULATOR SWITCH ASSEMBLY - MULTIPLEX NETWORK DOOR ECU AND BODY GROUND)
  1. Disconnect the f1 back door power window regulator switch connector.

  1. Disconnect the V2 multiplex network door ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    f1-8 (AUTO) - V2-21 (AUTO)
    Always
    Below 1 Ω
    f1-1 (E) - Body ground
    Always
    Below 1 Ω
    f1-8 (AUTO) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MULTIPLEX NETWORK DOOR ECU (BACK DOOR P/W) (Click here)