Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › OCCUPANT CLASSIFICATION SYSTEM

DTC    B1780    Front Occupant Classification Sensor LH Circuit Malfunction

for Preparation Click here


DESCRIPTION

The front occupant classification sensor LH circuit consists of the occupant classification ECU and front occupant classification sensor LH.
DTC B1780 is stored when a malfunction is detected in the front occupant classification sensor LH circuit.

DTC Code
DTC Detection Condition
Trouble Area
B1780
One of the following conditions is met:
  1. Occupant classification ECU detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to +B signal in the front occupant classification sensor LH circuit for 2 seconds.
  2. Front occupant classification sensor LH malfunction.
  3. Occupant classification ECU malfunction.
  1. Separate type front seat cushion spring RH (Front occupant classification sensor LH)
  2. Front seat wire RH
  3. Occupant classification ECU

HINT:
  1. When DTC B1650/32 is stored as a result of troubleshooting the airbag system, perform troubleshooting for DTC B1780 of the occupant classification system.
  2. Use the Techstream to check for DTCs of the occupant classification ECU, otherwise the DTCs cannot be read.


WIRING DIAGRAM


B151586E23


INSPECTION PROCEDURE

HINT:
  1. If troubleshooting (wire harness inspection) is difficult to perform, remove the front seat RH installation bolts to see the undersurface of the seat cushion.
  2. In the above case, hold the seat so that it does not fall down. Holding the seat for a long period of time may cause problems, such as seat rail deformation. Hold the seat up only for as long as necessary.

1.CHECK FOR DTC
  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in memory (Click here).

    HINT:
    1. First clear the DTCs stored in the occupant classification ECU, and then clear the DTCs stored in the center airbag sensor.
    2. Use the Techstream to clear the DTCs of the occupant classification ECU, otherwise the DTCs cannot be cleared.

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Using the Techstream, check for DTCs of the occupant classification ECU (Click here).

    OK:
    DTC B1780 is not output.

    HINT:
    DTCs other than DTC B1780 may be output at this time, but they are not related to this check.



NG
Go to step 2
OK

USE SIMULATION METHOD TO CHECK (Click here)  

2.CHECK CONNECTION OF CONNECTOR
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the occupant classification ECU and front occupant classification sensor LH.

    OK:
    Connectors are properly connected.



NG
CONNECT CONNECTOR
OK


3.CHECK CONNECTOR
  1. Disconnect the connectors from the occupant classification ECU and front occupant classification sensor LH.

  1. Check that the connectors (on the occupant classification ECU side and front occupant classification sensor LH side) are not damaged (Click here).

    OK:
    Connectors are not deformed or damaged.



NG
REPLACE FRONT SEAT WIRE RH
OK


4.CHECK FRONT SEAT WIRE RH


    C213684E01
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    a10-1 (SGD1) - Body ground
    Ignition switch ON
    Below 1 V
    a10-7 (SIG1) - Body ground
    a10-11 (SVC1) - Body ground

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Using service wires, connect terminals 1 (SVC1) and 3 (SGD1), and terminals 2 (SIG1) and 3 (SGD1) of connector C.

    NOTICE:
    Do not forcibly insert the service wires into the terminals of the connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    a10-7 (SIG1) - a10-1 (SGD1)
    Always
    Below 1 Ω
    a10-11 (SVC1) - a10-1 (SGD1)

  1. Disconnect the service wires from connector C.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    a10-7 (SIG1) - a10-1 (SGD1)
    Always
    1 MΩ or higher
    a10-11 (SVC1) - a10-1 (SGD1)
    a10-7 (SIG1) - a10-11 (SVC1)
    a10-1 (SGD1) - Body ground
    a10-7 (SIG1) - Body ground
    a10-11 (SVC1) - Body ground

    Text in Illustration 
    *1
    Front Seat Wire RH
    *2
    Front Occupant Classification Sensor LH
    *3
    Occupant Classification ECU
    *4
    Service Wire
    *5
    Connector C
    *6
    Connector B
    *a
    Front view of wire harness connector
    (to Front Occupant Classification Sensor LH)
    *b
    Front view of wire harness connector
    (to Occupant Classification ECU)



NG
REPLACE FRONT SEAT WIRE RH
OK


5.CHECK FOR DTC
  1. Connect the connectors to the occupant classification ECU and front occupant classification sensor LH.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear any DTCs stored in memory (Click here).

    HINT:
    1. First clear the DTCs stored in the occupant classification ECU, and then clear the DTCs stored in the center airbag sensor.
    2. Use the Techstream to clear the DTCs of the occupant classification ECU, otherwise the DTCs cannot be cleared.

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Using the Techstream, check for DTCs of the occupant classification ECU (Click here).

    OK:
    DTC B1780 is not output.

    HINT:
    DTCs other than DTC B1780 may be output at this time, but they are not related to this check.



NG
Go to step 6
OK

USE SIMULATION METHOD TO CHECK (Click here)  

6.REPLACE OCCUPANT CLASSIFICATION ECU
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Replace the occupant classification ECU (Click here).

    HINT:
    Perform the inspection using parts from a normal vehicle when possible.


NEXT


7.PERFORM ZERO POINT CALIBRATION
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Using the Techstream, perform the zero point calibration (Click here).

    OK:
    "Zero Point Calibration is complete." is displayed.



NG
Go to step 10
OK


8.PERFORM SENSITIVITY CHECK
  1. Using the Techstream, perform the sensitivity check (Click here).

    Standard range:
    27 to 33 kg (59.5 to 72.8 lb)



NG
Go to step 10
OK


9.CHECK FOR DTC
  1. Clear the DTCs stored in memory (Click here).

    HINT:
    1. First clear the DTCs stored in the occupant classification ECU, and then clear the DTCs stored in the center airbag sensor.
    2. Use the Techstream to clear the DTCs of the occupant classification ECU, otherwise the DTCs cannot be cleared.

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Using the Techstream, check for DTCs of the occupant classification ECU (Click here).

    OK:
    DTC B1780 is not output.

    HINT:
    DTCs other than DTC B1780 may be output at this time, but they are not related to this check.



NG
Go to step 10
OK

END 

10.REPLACE SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY RH
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. for Manual Seat:

    1. Replace the separate type front seat cushion spring RH (Click here).

  1. for Power Seat:

    1. Replace the separate type front seat cushion spring RH (Click here).

HINT:
Perform the inspection using parts from a normal vehicle when possible.


NEXT


11.PERFORM ZERO POINT CALIBRATION
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Using the Techstream, perform the zero point calibration (Click here).

    OK:
    "Zero Point Calibration is complete." is displayed.


NEXT


12.PERFORM SENSITIVITY CHECK
  1. Using the Techstream, perform the sensitivity check (Click here).

    Standard range:
    27 to 33 kg (59.5 to 72.8 lb)


NEXT

END