DTC B1782 Rear Occupant Classification Sensor LH Circuit Malfunction |
| DTC Code | DTC Detection Condition | Trouble Area |
| B1782 | One of the following conditions is met:
|
|

| 1.CHECK FOR DTC |
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Using the Techstream, check for DTCs of the occupant classification ECU (Click here).
|
| ||||
| OK | ||
| ||
| 2.CHECK CONNECTION OF CONNECTOR |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Check that the connectors are properly connected to the occupant classification ECU and rear occupant classification sensor LH.
|
| ||||
| OK | |
| 3.CHECK CONNECTOR |
Disconnect the connectors from the occupant classification ECU and rear occupant classification sensor LH.
Check that the connectors (on the occupant classification ECU side and rear occupant classification sensor LH side) are not damaged (Click here).
|
| ||||
| OK | |
| 4.CHECK FRONT SEAT WIRE RH |
![]() |
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| a10-3 (SGD3) - Body ground | Ignition switch ON | Below 1 V |
| a10-5 (SVC3) - Body ground | ||
| a10-9 (SIG3) - Body ground |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Using service wires, connect terminals 1 (SVC3) and 3 (SGD3), and terminals 2 (SIG3) and 3 (SGD3) of connector C.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| a10-5 (SVC3) - a10-3 (SGD3) | Always | Below 1 Ω |
| a10-9 (SIG3) - a10-3 (SGD3) |
Disconnect the service wires from connector C.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| a10-5 (SVC3) - a10-3 (SGD3) | Always | 1 MΩ or higher |
| a10-9 (SIG3) - a10-3 (SGD3) | ||
| a10-5 (SVC3) - a10-9 (SIG3) | ||
| a10-3 (SGD3) - Body ground | ||
| a10-5 (SVC3) - Body ground | ||
| a10-9 (SIG3) - Body ground |
| *1 | Front Seat Wire RH |
| *2 | Rear Occupant Classification Sensor LH |
| *3 | Occupant Classification ECU |
| *4 | Service Wire |
| *5 | Connector C |
| *6 | Connector B |
| *a | Front view of wire harness connector (to Rear Occupant Classification Sensor LH) |
| *b | Front view of wire harness connector (to Occupant Classification ECU) |
|
| ||||
| OK | |
| 5.CHECK FOR DTC |
Connect the connectors to the occupant classification ECU and rear occupant classification sensor LH.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Using the Techstream, check for DTCs of the occupant classification ECU (Click here).
|
| ||||
| OK | ||
| ||
| 6.REPLACE OCCUPANT CLASSIFICATION ECU |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Replace the occupant classification ECU (Click here).
| NEXT | |
| 7.PERFORM ZERO POINT CALIBRATION |
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Using the Techstream, perform the zero point calibration (Click here).
|
| ||||
| OK | |
| 8.PERFORM SENSITIVITY CHECK |
Using the Techstream, perform the sensitivity check (Click here).
|
| ||||
| OK | |
| 9.CHECK FOR DTC |
Clear the DTCs stored in memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Using the Techstream, check for DTCs of the occupant classification ECU (Click here).
|
| ||||
| OK | ||
| ||
| 10.REPLACE SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY RH |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
for Manual Seat:
Replace the separate type front seat cushion spring RH (Click here).
for Power Seat:
Replace the separate type front seat cushion spring RH (Click here).
| NEXT | |
| 11.PERFORM ZERO POINT CALIBRATION |
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Using the Techstream, perform the zero point calibration (Click here).
| NEXT | |
| 12.PERFORM SENSITIVITY CHECK |
Using the Techstream, perform the sensitivity check (Click here).
| NEXT | ||
| ||