Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM

DTC    P0171    System Too Lean (Bank 1)

DTC    P0172    System Too Rich (Bank 1)

DTC    P0174    System Too Lean (Bank 2)

DTC    P0175    System Too Rich (Bank 2)

for Preparation Click here


DESCRIPTION

The fuel trim is related to the feedback compensation value, not to the basic injection duration. The fuel trim consists of both the short-term and long-term fuel trim.
The short-term fuel trim is fuel compensation that is used to constantly maintain the air fuel ratio at stoichiometric levels. The signal from the air fuel ratio sensor indicates whether the air fuel ratio is rich or lean compared to the stoichiometric ratio. This triggers a reduction in the fuel injection volume if the air fuel ratio is rich and an increase in the fuel injection volume if it is lean.
Factors such as individual engine differences, wear over time and changes in operating environment cause short-term fuel trim to vary from the central value. The long-term fuel trim, which controls overall fuel compensation, compensates for long-term deviations in the fuel trim from the central value caused by the short-term fuel trim compensation.
If both the short-term and long-term fuel trim are lean or rich beyond predetermined values, it is interpreted as a malfunction, and the ECM illuminates the MIL and sets a DTC.

DTC No.
DTC Detection Condition
Trouble Area
P0171
P0174
With warm engine and stable air fuel ratio feedback, fuel trim considerably in error to lean side (2 trip detection logic)
  1. Intake system
  2. Fuel injector assembly blockage
  3. Mass air flow meter
  4. Engine coolant temperature sensor
  5. Fuel pressure
  6. Gas leaks from exhaust system
  7. Open or short in air fuel ratio sensor (bank 1, 2 sensor 1) circuit
  8. Air fuel ratio sensor (bank 1, 2 sensor 1)
  9. No.1 integration relay (A/F)
  10. PCV valve and hose
  11. PCV hose connections
  12. Wire harness or connector
  13. ECM
P0172
P0175
With warm engine and stable air fuel ratio feedback, fuel trim considerably in error to rich side (2 trip detection logic)
  1. Fuel injector assembly leak or blockage
  2. Mass air flow meter
  3. Engine coolant temperature sensor
  4. Ignition system
  5. Fuel pressure
  6. Gas leaks from exhaust system
  7. Open or short in air fuel ratio sensor (bank 1, 2 sensor 1) circuit
  8. Air fuel ratio sensor (bank 1, 2 sensor 1)
  9. No.1 integration relay (A/F)
  10. Wire harness or connector
  11. ECM

HINT:
  1. When DTC P0171 or P0174 is set, the actual air fuel ratio is on the lean side. When DTC P0172 or P0175 is set, the actual air fuel ratio is on the rich side.
  2. If the vehicle runs out of fuel, the air fuel ratio is lean and DTC P0171 or P0174 may be set. The MIL is then illuminated.
  3. When the total of the short-term and long-term fuel trim values is within the malfunction threshold (and the engine coolant temperature is more than 75°C (167°F)), the system is functioning normally.


MONITOR DESCRIPTION

Under closed-loop fuel control, fuel injection volumes that deviate from those estimated by the ECM cause changes in the long-term fuel trim compensation value. The long-term fuel trim is adjusted when there are persistent deviations in the short-term fuel trim values. Deviations from the ECM's estimated fuel injection volumes also affect the average fuel trim learning value, which is a combination of the average short-term fuel trim (fuel feedback compensation value) and the average long-term fuel trim (learning value of the air fuel ratio). If the average fuel trim learning value exceeds the malfunction thresholds, the ECM interprets this as a fault in the fuel system and sets a DTC.
Example:

  1. When the average fuel trim learning value is +35% or more, or -35% or less, the ECM interprets this as a fuel system malfunction.


    A082386E30


MONITOR STRATEGY


Related DTCs
P0171: Fuel trim Lean (Bank 1)
P0172: Fuel trim Rich (Bank 1)
P0174: Fuel trim Lean (Bank 2)
P0175: Fuel trim Rich (Bank 2)
Required Sensors / Components
Air fuel ratio sensor, Mass air flow meter, Crankshaft position sensor
Frequency of Operation
Continuous
Duration
Less than 10 seconds
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Fuel Trim 
Monitor runs whenever following DTCs are not present
P0010, P0020 (Camshaft timing oil control valve assembly bank 1, 2)
P0011, P0021 (VVT system bank 1, 2 - advance)
P0012, P0022 (VVT system bank 1, 2 - retard)
P0013, P0023 (Exhaust camshaft timing oil control valve assembly bank 1, 2)
P0014, P0024 (Exhaust VVT system bank 1, 2 - advance)
P0015, P0025 (Exhaust VVT system bank 1, 2 - retard)
P0016, P0018 (VVT system bank 1, 2 - misalignment)
P0017, P0019 (Exhaust VVT system bank 1, 2 - misalignment)
P0031, P0032, P0051, P0052, P101D, P103D (Air fuel ratio sensor heater)
P0102, P0103 (Mass air flow meter)
P0115, P0117, P0118 (Engine coolant temperature sensor)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor)
P0125 (Insufficient coolant temperature for closed loop fuel control)
P0335 (Crankshaft position sensor)
P0340, P0342, P0343, P0345, P0347, P0348 (VVT sensor)
P0351, P0352, P0353, P0354, P0355, P0356 (Igniter)
P0365, P0367, P0368, P0390, P0392, P0393 (Exhaust VVT sensor)
P0500 (Vehicle speed sensor)
P0412, P1613 (Secondary Air Injection System Control)
P0416, P0417, P2440, P2441, P2442, P2443, P2444, P2445 (Secondary Air Injection System)
P219A, P219B (Air fuel ratio imbalance)
Fuel system status
Closed-loop
Battery voltage
11 V or more
One of the following conditions is met:
Condition 1, 2 or 3
1. Engine speed
Less than 1100 rpm
2. Engine load
10% or more
3. Either of the following conditions is met:
Condition (a) or (b)
(a). Idle
ON
(b). Vehicle speed
Less than 1.15 km/h (1.875 mph)
Catalyst monitor
Not executed

TYPICAL MALFUNCTION THRESHOLDS


Fuel Trim 
EVAP purge-cut
Executing
Either of the following conditions is met:
Condition 1 or 2
1. Average between short-term fuel trim and long-term fuel trim
35% or more (varies with engine coolant temperature)
2. Average between short-term fuel trim and long-term fuel trim
-35% or less (varies with engine coolant temperature)

CONFIRMATION DRIVING PATTERN


A199233E44

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on [A].
  6. Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher with all the accessories switched off [B].
  7. With the engine warmed up, idle the engine for 2 minutes or more [C].
  8. Drive the vehicle at a speed between 60 and 135 km/h (38 and 85 mph) for 5 minutes or more [D].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  9. Enter the following menus: Powertrain / Engine / Trouble Codes / Pending [E].
  10. Read the pending DTCs.

    HINT:
    If a pending DTC is output, the system is malfunctioning.

  11. If no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM

Refer to DTC P0102 .
Refer to DTC P2195 .

INSPECTION PROCEDURE

HINT:
Malfunctioning areas can be identified by performing the Control the Injection Volume function provided in the Active Test. The Control the Injection Volume function can help to determine whether the air fuel ratio sensor, heated oxygen sensor and other potential trouble areas are malfunctioning.
The following instructions describe how to conduct the Control the Injection Volume operation using the Techstream.
  1. Connect the Techstream to the DLC3.
  2. Start the engine.
  3. Turn the Techstream on.
  4. Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.
  5. Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume / AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2.
  6. Perform the Active Test operation with the engine idling (press the RIGHT or LEFT button to change the fuel injection volume).
  7. Monitor the output voltages of the air fuel ratio and heated oxygen sensors (AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2) displayed on the Techstream.

HINT:
  1. Change the fuel injection volume within the range of -12.5% to 12.5%. The injection volume can be changed in fine gradations.
  2. Each sensor reacts in accordance with increases and decreases in the fuel injection volume.


Techstream Display (Sensor)
Injection Volume
Status
Voltage
AFS Voltage B1S1 or AFS Voltage B2S1
(Air fuel ratio)
12.5%
Rich
Below 3.1 V
-12.5%
Lean
Higher than 3.4 V
O2S B1S2 or O2S B2S2
(Heated oxygen)
12.5%
Rich
Higher than 0.55 V
12.5%
Lean
Below 0.4 V

NOTICE:
The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.


Case
Air Fuel Ratio Sensor (Sensor 1) Output Voltage
Heated Oxygen Sensor (Sensor 2) Output Voltage
Main Suspected Trouble Area
1
A150787E11
A151324E08
A150787E11
A150788E06
-
2
A150787E11
A150790E01
A150787E11
A150788E06
  1. Air fuel ratio sensor
  2. Air fuel ratio sensor heater
  3. Air fuel ratio sensor circuit
3
A150787E11
A151324E08
A150787E11
A150790E01
  1. Heated oxygen sensor
  2. Heated oxygen sensor heater
  3. Heated oxygen sensor circuit
4
A150787E11
A150790E01
A150787E11
A150790E01
  1. Fuel injector assembly
  2. Fuel pressure
  3. Gas leak from exhaust system (Air fuel ratio extremely rich or lean)
  1. Following the Control the Injection Volume procedure enables technicians to check and graph the voltage outputs of both the air fuel ratio and heated oxygen sensors.
  2. To display the graph, enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume / AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2; and then press the graph button on the Data List view.

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
  1. Bank 1 refers to the bank that includes the No. 1 cylinder*.
    *: The No. 1 cylinder is the cylinder which is farthest from the transaxle.
  2. Bank 2 refers to the bank that does not include the No. 1 cylinder.
  3. Sensor 1 refers to the sensor closest to the engine assembly.
  4. Sensor 2 refers to the sensor farthest away from the engine assembly.
  5. Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  6. A low air fuel ratio sensor voltage could be caused by a rich air fuel mixture. Check for conditions that would cause the engine to run rich.
  7. A high air fuel ratio sensor voltage could be caused by a lean air fuel mixture. Check for conditions that would cause the engine to run lean.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0171, P0172, P0174 OR P0175)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine / Trouble Codes.

  1. Read the DTCs.

    Result:

    Result
    Proceed to
    DTC P0171, P0172, P0174 and/or P0175 are output
    A
    DTC P0171, P0172, P0174 or P0175 and other DTCs are output
    B

    HINT:
    If any DTCs other than P0171, P0172, P0174 or P0175 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.CHECK PCV HOSE CONNECTIONS
  1. Check the PCV hose connections.

OK:
PCV hose is connected correctly and is not damaged.



NG
REPAIR OR REPLACE PCV HOSE (Click here)
OK


3.CHECK INTAKE SYSTEM
  1. Check the intake system for vacuum leaks (Click here).

    OK:
    No leaks in intake system.



NG
REPAIR OR REPLACE INTAKE SYSTEM
OK


4.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE INJECTION VOLUME)
  1. Connect the Techstream to the DLC3.

  1. Start the engine.

  1. Turn the Techstream on.

  1. Warm up the engine and run the engine at an engine speed of 2500 rpm for approximately 90 seconds.

  1. Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume / AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2.

  1. Perform the Control the Injection Volume operation with the engine idling (press the RIGHT or LEFT button to change the fuel injection volume).

  1. Monitor the voltage outputs of the air fuel ratio sensor and the heated oxygen sensor (AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2) displayed on the Techstream.

    HINT:
    1. Change the fuel injection volume within the range of -12.5% to 12.5%. The injection volume can be changed in fine gradations.
    2. The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.
    3. If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.


    Standard:

    Techstream Display
    (Sensor)
    Injection Volume
    Status
    Voltage
    AFS Voltage B1S1 or AFS Voltage B2S1
    (Air fuel ratio)
    12.5%
    Rich
    Below 3.1 V
    -12.5%
    Lean
    Higher than 3.4 V
    O2S B1S2 or O2S B2S2
    (Heated oxygen)
    12.5%
    Rich
    Higher than 0.55 V
    -12.5%
    Lean
    Below 0.4 V


    Result 
    Status
    AFS Voltage B1S1 or AFS Voltage B2S1
    Status
    O2S B1S2 or O2S B2S2
    Air Fuel Ratio Condition and
    Air Fuel Ratio Sensor Condition
    Suspected Trouble Area
    Proceed to
    Lean/Rich
    Lean/Rich
    Normal
    -
    A
    Lean
    Lean
    Actual air fuel ratio lean
    1. PCV valve and hose
    2. PCV hose connections
    3. Fuel injector assembly blockage
    4. Gas leak from exhaust system
    5. Intake system
    6. Fuel pressure
    7. Mass air flow meter
    8. Engine coolant temperature sensor
    A
    Rich
    Rich
    Actual air fuel ratio rich
    1. Fuel injector assembly leak or blockage
    2. Gas leak from exhaust system
    3. Ignition system
    4. Fuel pressure
    5. Mass air flow meter
    6. Engine coolant temperature sensor
    A
    Lean
    Lean/Rich
    Air fuel ratio sensor malfunction
    1. Air fuel ratio sensor
    B
    Rich
    Lean/Rich
    Air fuel ratio sensor malfunction
    1. Air fuel ratio sensor
    B
    1. Lean: During Control the Injection Volume, the air fuel ratio sensor output voltage (AFS Voltage B1S1 or AFS Voltage B2S1) is consistently higher than 3.4 V, and the heated oxygen sensor output voltage (O2S B1S2 or O2S B2S2) is consistently below 0.4 V.
    2. Rich: During Control the Injection Volume, the AFS Voltage B1S1 or AFS Voltage B2S1 is consistently below 3.1 V, and the O2S B1S2 or O2S B2S2 is consistently higher than 0.55 V.
    3. Lean/Rich: During Control the Injection Volume of the Active Test, the output voltage of the heated oxygen sensor alternates correctly.

    HINT:
    Refer to "Data List / Active Test" [AFS Voltage B1S1, AFS Voltage B2S1, O2S B1S2 and O2S B2S2] (Click here).



B
Go to step 11
A


5.READ VALUE USING TECHSTREAM (COOLANT TEMP)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine / Data List / Coolant Temp.

  1. Read the Data List twice, when the engine is both cold and warmed up.

    Standard:
    With cold engine:
    Same as ambient air temperature.
    With warm engine:
    Between 75°C and 100°C (167°F and 212°F)



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)
OK


6.READ VALUE USING TECHSTREAM (MAF)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine / Data List / MAF and Coolant Temp.

  1. Allow the engine to idle until Coolant Temp reaches 75°C (167°F) or higher.

  1. Read MAF with the engine speed at 2500 rpm.

    Standard:
    Between 8 gm/sec and 19 gm/sec (shift lever: N, A/C: Off).



NG
Go to step 16
OK


7.CHECK FUEL PRESSURE
  1. Check the fuel pressure .



NG
REPAIR OR REPLACE FUEL SYSTEM
OK


8.CHECK FOR EXHAUST GAS LEAK
  1. Check for exhaust gas leaks.

OK:
No gas leaks.



NG
REPAIR OR REPLACE EXHAUST SYSTEM
OK


9.CHECK FOR SPARK (SPARK TEST)
  1. Perform a spark test .

    HINT:
    If the result of the spark test is normal, proceed to the next step.


NEXT


10.INSPECT FUEL INJECTOR ASSEMBLY (INJECTION AND VOLUME)
  1. Check the injection and volume (Click here).



OK
Go to step 15

NG
REPLACE FUEL INJECTOR ASSEMBLY (Click here)

11.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)
  1. Inspect the air fuel ratio sensor (Click here).



NG
REPLACE AIR FUEL RATIO SENSOR (Click here)
OK


12.CHECK TERMINAL VOLTAGE (+B TERMINAL OF AIR FUEL RATIO SENSOR)
A150242E34
  1. Disconnect the air fuel ratio sensor connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    B26-2 (+B) - Body ground
    Ignition switch ON
    11 to 14 V
    B27-2 (+B) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *A
    Bank 1
    *B
    Bank 2
    *a
    Front view of wire harness connector
    (to Air Fuel Ratio Sensor)

  1. Reconnect the air fuel ratio sensor connector.



NG
Go to step 21
OK


13.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
  1. Disconnect the air fuel ratio sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B26-1 (HA1A) - B39-17 (HA1A)
    Always
    Below 1 Ω
    B27-1 (HA2A) - B39-19 (HA2A)
    Always
    Below 1 Ω
    B26-1 (HA1A) or B39-17 (HA1A) - Body ground
    Always
    10 kΩ or higher
    B27-1 (HA2A) or B39-19 (HA2A) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the air fuel ratio sensor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
OK


14.REPLACE AIR FUEL RATIO SENSOR
  1. Replace the air fuel ratio sensor (Click here).


NEXT


15.PERFORM CONFIRMATION DRIVING PATTERN
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Start the engine and warm it up.

  1. Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine / Trouble Codes / Pending.

  1. Read the pending DTCs.

    Result:

    Result
    Proceed to
    DTC P0171, P0172, P0174 or P0175 is output
    A
    DTC is not output
    B



B
END
A


16.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER CONNECTOR CONNECTION)
  1. Check the connection and terminal contact pressure of connectors and wire harnesses between the mass air flow meter and ECM (Click here).

    HINT:
    Repair any problems.


NEXT


17.CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Start the engine and warm it up.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine / Trouble Codes / Pending.

  1. Read the pending DTCs.

    Result 
    Result
    Proceed to
    DTC P0171, P0172, P0174 or P0175 is output
    A
    DTC is not output
    B



B
END
A


18.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
  1. Disconnect the mass air flow meter connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B35-5 (VG) - B37-14 (VG)
    Always
    Below 1 Ω
    B35-4 (E2G) - B37-13 (E2G)
    Always
    Below 1 Ω
    B35-5 (VG) or B37-14 (VG) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the mass air flow meter connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


19.REPLACE MASS AIR FLOW METER
  1. Replace the mass air flow meter (Click here).

    HINT:
    If the result of the inspection performed in step 6 indicated no problem, proceed to the next step without replacing the mass air flow meter.


NEXT


20.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Start the engine and warm it up.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine / Trouble Codes / Pending.

  1. Read the pending DTCs.

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC P0171, P0172, P0174 or P0175 is output
    B



B
REPLACE ECM (Click here)
A

END 

21.INSPECT NO.1 INTEGRATION RELAY (A/F)
  1. Inspect the No. 1 integration relay (A/F) .



NG
REPLACE NO.1 INTEGRATION RELAY
OK


22.CHECK HARNESS AND CONNECTOR (NO.1 INTEGRATION RELAY - A/F SENSOR AND BODY GROUND)
  1. Disconnect the air fuel ratio sensor connector.

  1. Remove the No. 1 integration relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B26-2 (+B) - 1D-8
    Always
    Below 1 Ω
    B27-2 (+B) - 1D-8
    Always
    Below 1 Ω
    1D-7 - Body ground
    Always
    Below 1 Ω
    B26-2 (+B) or 1D-8 - Body ground
    Always
    10 kΩ or higher
    B27-2 (+B) or 1D-8 - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the air fuel ratio sensor connector.

  1. Reinstall the No. 1 integration relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (NO.1 INTEGRATION RELAY - A/F SENSOR AND BODY GROUND)
OK

CHECK ECM POWER SOURCE CIRCUIT (Click here)