Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART KEY SYSTEM (for Entry Function)

SMART KEY SYSTEM (for Entry Function) > All Door Entry Lock/Unlock Functions and Wireless Functions do not Operate

for Preparation Click here


DESCRIPTION

When the entry operation and wireless operation of the door lock functions do not operate, a malfunction or wave interference may be occurring in either of the following: 1) the signal communication line between the door control receiver and certification ECU (the line is used by entry and wireless operations); or 2) the electrical key transmitter.

WIRING DIAGRAM


B211013E06


INSPECTION PROCEDURE

NOTICE:
  1. The smart key system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the smart key system (for Entry Function) after confirming that the communication systems are functioning properly.
  2. When using the Techstream with the engine switch off to troubleshoot: Connect the Techstream to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the Techstream and vehicle begins.
  3. Check that there are no electrical key transmitters in the vehicle.
  4. Before performing the inspection, check that DTC B1242 (wireless door lock control) is not output (Click here).
  5. Inspect the fuses for circuits related to this system before performing the following inspection procedure.
  6. When checking the entry lock operation multiple times, the lock operation may be limited to 2 consecutive operations depending on the settings. In order to perform the entry lock operation 3 or more times, an unlock operation must be performed once (any type of unlock operation is sufficient). However, only consecutive entry lock operations are limited. Using the wireless lock or other types of lock operations, it is possible to perform consecutive lock operations without this limitation.
  7. Before replacing the certification ECU, refer to the engine immobiliser system (w/ Smart Key System) (Click here).

1.CHECK POWER DOOR LOCK CONTROL SYSTEM
  1. When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation (Click here).

    OK:
    Door locks operate normally.



NG
GO TO POWER DOOR LOCK CONTROL SYSTEM (Click here)
OK


2.CHECK ELECTRICAL KEY TRANSMITTER
  1. When another registered electrical key transmitter is used, check that the wireless and entry functions operate normally (Click here).
    Result 
    Result
    Proceed to
    Entry function operates
    A
    Entry function does not operate
    B



B
Go to step 5
A


3.CHECK ELECTRICAL KEY TRANSMITTER (LED)
  1. Check that the transmitter LED illuminates 3 times when a switch is pressed 3 times.
    Result 
    Result
    Proceed to
    Transmitter LED does not illuminate when switch is pressed 3 times
    A
    Transmitter LED illuminates 3 times when switch is pressed 3 times
    B
    Transmitter LED does not illuminate second or third time
    C

    HINT:
    If the transmitter LED does not illuminate the second or third time, replace the transmitter battery as it is depleted.



B
REPLACE ELECTRICAL KEY TRANSMITTER

C
REPLACE TRANSMITTER BATTERY (Click here)
A


4.INSPECT TRANSMITTER BATTERY (VOLTAGE)


    B246343E01
  1. Remove the battery from the electrical key transmitter that does not operate (Click here).

  1. Attach a lead wire (0.6 mm (0.0236 in.) in diameter or less including wire sheath) with tape or equivalent to the negative terminal.
    Text in Illustration 
    *1
    Lead Wire

    NOTICE:
    Do not wrap the lead wire around a terminal, wedge it between terminals, or solder it. The terminal may be deformed or damaged, and the battery will not be able to be installed correctly.

  1. Carefully pull the lead wire out from the position shown in the illustration and install the previously removed transmitter battery.



    B246344E01
  1. Using an oscilloscope, check the transmitter battery voltage waveform.

    HINT:
    When measuring the battery voltage, bring the electrical key transmitter within the entry operating range while operating the lock sensor of a door handle to perform the measurement. For the entry operating range, refer to System Description (Click here).

    Standard Voltage:
    Item
    Content
    Tester Connection
    Battery positive (+) - Battery negative (-)
    Tool Setting
    0.5 V/DIV., 100 ms/DIV.
    Condition
    Engine switch off, all doors closed and lock sensor touched
    Specified Condition
    2.5 to 3.2 V (Refer to waveform)

    Text in Illustration 
    *1
    Measurement Position



NG
REPLACE TRANSMITTER BATTERY (Click here)
OK

REPLACE ELECTRICAL KEY TRANSMITTER 

5.CHECK WAVE ENVIRONMENT
  1. Bring the electrical key transmitter near the door control receiver and perform a wireless and entry function operation check.

    HINT:
    1. When the electrical key transmitter is brought near the door control receiver, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.
    2. If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

    OK:
    Wireless and entry functions operate normally.



NG
Go to step 6
OK

AFFECTED BY WAVE INTERFERENCE 

6.CHECK POWER SOURCE
  1. Check that the combination meter display turns off when the engine switch is turned off.

    OK:
    Combination meter turns off.

    HINT:
    This confirms that systems other than the smart key system are correctly detecting the state of the power source.



NG
GO TO SMART KEY SYSTEM (FOR START FUNCTION)
OK


7.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - BATTERY AND BODY GROUND)
B199585E09
  1. Disconnect the F79 ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    F79-17 (CUTB) - Body ground
    Always
    11 to 14 V
    F79-1 (+B) - Body ground
    Always
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F79-15 (E) - Body ground
    Always
    Below 1 Ω

Text in Illustration 
*a
Front view of wire harness connector
(to Certification ECU)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - CERTIFICATION ECU AND BODY GROUND)
  1. Disconnect the O10 receiver connector.

  1. Disconnect the F78 ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O10-4 (+5) - F78-5 (RCO)
    Always
    Below 1 Ω
    O10-5 (DATA) - F78-15 (RDA)
    Always
    Below 1 Ω
    O10-2 (RSSI) - F78-16 (RSSI)
    Always
    Below 1 Ω
    F78-5 (RCO) - Body ground
    Always
    10 kΩ or higher
    F78-15 (RDA) - Body ground
    Always
    10 kΩ or higher
    F78-16 (RSSI) - Body ground
    Always
    10 kΩ or higher
    O10-1 (GND) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9.CHECK DOOR CONTROL RECEIVER (OPERATION)
  1. Temporarily replace the door control receiver with a new or normally functioning one (Click here).

  1. Check that the wireless and entry functions operate normally.

    OK:
    Wireless and entry functions operate normally.



NG
REPLACE CERTIFICATION ECU (Click here)
OK

END (DOOR CONTROL RECEIVER IS DEFECTIVE)