Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)

DTC    B14A3    Front Passenger Side Solar Sensor Short Circuit

for Preparation Click here


DESCRIPTION

E132508E01
The automatic light control sensor (solar sensor), which is installed on the upper side of the instrument panel, detects sunlight and controls the air conditioning in auto mode. The output current from the solar sensor varies according to the amount of sunlight. When the amount of sunlight increases, the output current increases. As the amount of sunlight decreases, the output current decreases. The air conditioning amplifier assembly detects the output current from the solar sensor.

DTC Code
DTC Detection Condition
Trouble Area
B14A3
An open or short in the passenger side solar sensor circuit.
  1. Automatic light control sensor (solar sensor)
  2. Harness or connector
  3. Main body ECU (multiplex network body ECU)
  4. Air conditioning amplifier assembly

WIRING DIAGRAM


E196914E10


INSPECTION PROCEDURE

HINT:
  1. If DTC B1244 is output together with other DTCs, troubleshoot DTC B1244 first (Click here).
  2. If the check is performed in a dark place, DTC B14A2 or B14A3 (solar sensor circuit abnormal) may be stored even though the system is normal.

1.READ VALUE USING TECHSTREAM (SOLAR SENSOR)
  1. Use the Data List to check if the automatic light control sensor (solar sensor) is functioning properly (Click here).

    Air Conditioner 
    Tester Display
    Measurement Item/Rang
    Normal Condition
    Diagnostic Note
    Solar Sensor (P side)
    Automatic light control sensor (solar sensor) / Min.: 0, Max.: 255
    Passenger side solar sensor voltage increases as brightness increases
    Open in the circuit: 0.
    Short in the circuit: 255.

    OK:
    The display is as specified in the normal condition column.

    Result 
    Result
    Proceed to
    OK (When troubleshooting according to problem symptoms table)
    A
    OK (When troubleshooting according to the DTC)
    B
    NG
    C



B
REPLACE AIR CONDITIONING AMPLIFIER ASSESMBLY (Click here)

C
Go to step 2
A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
E152686E56
  1. Disconnect the G2 sensor connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    G2-6 (CLTB) - G2-3 (CLTE)
    Ignition switch off
    Below 1 V
    G2-6 (CLTB) - G2-3 (CLTE)
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Automatic Light Control Sensor [Solar Sensor])



NG
Go to step 5
OK


3.CHECK HARNESS AND CONNECTOR (SOLAR SENSOR - AIR CONDITIONING AMPLIFIER)
  1. Disconnect the G2 sensor connector.

  1. Disconnect the F42 amplifier connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G2-2 (TSR) - F42-32 (TSP)
    Always
    Below 1 Ω
    G2-2 (TSR) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK AUTOMATIC LIGHT CONTROL SENSOR (SOLAR SENSOR)


    E161710E48
  1. Remove the automatic light control sensor (solar sensor) with its connector still connected (Click here).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    G2-2 (TSR) - G2-3 (CLTE)
    Ignition switch ON
    Sensor subjected to electric light
    0.8 to 4.3 V
    G2-2 (TSR) - G2-3 (CLTE)
    Ignition switch ON
    Sensor covered with cloth
    Below 0.8 V

    Text in Illustration 
    *a
    Component with harness connected
    (Automatic Light Control Sensor [Solar Sensor])

    NOTICE:
    The connection procedure for using a digital tester such as a TOYOTA electrical tester is shown above. When using an analog tester, connect the negative (-) lead to terminal 2 and the positive (+) lead to terminal 3 of the solar sensor.

    HINT:
    1. Use an incandescent light for inspection. Bring it within about 30 cm (11.8 in.) of the solar sensor.
    2. As the inspection light is moved away from the sensor, the voltage decreases.



NG
REPLACE AUTOMATIC LIGHT CONTROL SENSOR (SOLAR SENSOR) (Click here)
OK

REPLACE AIR CONDITIONING AMPLIFIER ASSESMBLY (Click here)  

5.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - SOLAR SENSOR)
  1. Disconnect the F9 ECU connector.

  1. Disconnect the G2 sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F9-22 (CLTE) - G2-3 (CLTE)
    Always
    Below 1 Ω
    F9-20 (CLTB) - G2-6 (CLTB)
    Always
    Below 1 Ω
    F9-22 (CLTE) - Body ground
    Always
    10 kΩ or higher
    F9-20 (CLTB) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)