Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM

DTC    B15C3    Speaker Output Short

for Preparation Click here


DESCRIPTION

This DTC is stored when a malfunction occurs in the speakers.

DTC No.
DTC Detection Condition
Trouble Area
B15C3
A short is detected in the speaker output circuit.
  1. Harness or connector
  2. Speaker
  3. Radio and display receiver assembly

WIRING DIAGRAM



E283441E04


INSPECTION PROCEDURE

1.CHECK HARNESS AND CONNECTOR
  1. Disconnect the G47 and G48 radio and display receiver assembly connectors.

  1. Disconnect the H1 and I1 front No. 1 speaker assembly connectors.

  1. Disconnect the G1 and G10 front No. 2 speaker assembly connectors.

  1. Disconnect the J1 and K1 rear speaker assembly connectors.

  1. Disconnect the W5 and W6 rear No. 2 speaker assembly connectors.

  1. Measure the resistance between the radio and display receiver assembly and body ground to check for a short circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G47-1 (RR+) - Body ground
    Always
    10 kΩ or higher
    G47-2 (RL+) - Body ground
    Always
    10 kΩ or higher
    G47-3 (RR-) - Body ground
    Always
    10 kΩ or higher
    G47-6 (RL-) - Body ground
    Always
    10 kΩ or higher
    G48-1 (FR+) - Body ground
    Always
    10 kΩ or higher
    G48-2 (FL+) - Body ground
    Always
    10 kΩ or higher
    G48-5 (FR-) - Body ground
    Always
    10 kΩ or higher
    G48-6 (FL-) - Body ground
    Always
    10 kΩ or higher

  1. Measure the resistance between each of the front No. 2 speaker assemblies and body ground to check for a short circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G1-2 (TWL+) - Body ground
    Always
    10 kΩ or higher
    G1-4 (TWL-) - Body ground
    Always
    10 kΩ or higher
    G10-2 (TWR+) - Body ground
    Always
    10 kΩ or higher
    G10-4 (TWR-) - Body ground
    Always
    10 kΩ or higher

  1. Measure the resistance between each of the rear speaker assemblies and rear No. 2 speaker assemblies to check for a short circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    J1-2 - Body ground
    Always
    10 kΩ or higher
    K1-2 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY


    E144966E53
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H1-1 - H1-2
    Always
    4 Ω
    I1-1 - I1-2
    Always
    4 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Front No. 1 Speaker Assembly)
    *b
    for RH
    *c
    for LH



NG
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY (Click here)
OK


3.REPLACE FRONT NO. 2 SPEAKER ASSEMBLY
  1. Replace the front No. 2 speaker assembly with a known good one (Click here).

  1. Clear the DTCs (Click here).

  1. Recheck for DTCs and check that no DTCs are output (Click here).

    OK:
    No DTCs are output.

    HINT:
    1. Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.
    2. When there is a possibility that either the right or left front speaker is defective, inspect by interchanging the right one with the left one.
    3. Perform the above inspection on both LH and RH sides.



NG
Go to step 4
OK

END (FRONT NO. 2 SPEAKER ASSEMBLY WAS DEFECTIVE) 

4.INSPECT REAR SPEAKER ASSEMBLY


    E144966E54
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    J1-1 - J1-2
    Always
    4 Ω
    K1-1 - K1-2
    Always
    4 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Rear Speaker Assembly)
    *b
    for RH
    *c
    for LH



NG
REPLACE REAR SPEAKER ASSEMBLY (Click here)
OK


5.INSPECT REAR NO. 2 SPEAKER ASSEMBLY


    E144966E55
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    W5-1 - W5-2
    Always
    4 Ω
    W6-1 - W6-2
    Always
    4 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Rear No. 2 Speaker Assembly)
    *b
    for RH
    *c
    for LH



NG
REPLACE REAR NO. 2 SPEAKER ASSEMBLY (Click here)
OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)