DTC P0010 Camshaft Position "A" Actuator Circuit (Bank 1) |
DTC P0020 Camshaft Position "A" Actuator Circuit (Bank 2) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0010 | Oil control valve current is less than 0.306 A for intake camshaft circuit for 2 seconds or more (bank 1). (1 trip detection logic) |
|
| P0020 | Oil control valve current is less than 0.306 A for intake camshaft circuit for 2 seconds or more (bank 2). (1 trip detection logic) |
|

| GTS Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|

| 1.READ DTC OUTPUT |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTC after recording the freeze frame data and DTC.
Turn the ignition switch off.
Start the engine and allow the engine to idle.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read DTCs.
| Result | Proceed to |
| DTC P0010 or P0020 is output | A |
| DTC is not output | B |
|
| ||||
| A | |
| 2.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE (FOR INTAKE CAMSHAFT) |
Inspect the camshaft timing oil control valve (for intake camshaft) (Click here).
|
| ||||
| OK | |
| 3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF CAMSHAFT TIMING OIL CONTROL VALVE) |
![]() |
Disconnect the camshaft timing oil control valve (for intake camshaft connector).
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| C7-1 - Body ground | Ignition switch ON | 11 to 14 V |
| C24-1 - Body ground | Ignition switch ON | 11 to 14 V |
| *A | Bank 1 |
| *B | Bank 2 |
| *a | Front view of wire harness connector (to Camshaft Timing Oil Control Valve) |
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE - ECM) |
Disconnect the camshaft timing oil control valve (for intake camshaft connector).
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A36-17 (OC1) - C7-2 | Always | Below 1 Ω |
| A36-16 (OC2) - C24-2 | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| A36-17 (OC1) or C7-2 - Body ground | Always | 10 kΩ or higher |
| A36-16 (OC2) or C24-2 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 5.INSPECT RELAY (EFI MAIN1) |
Inspect EFI MAIN1 relay .
|
| ||||
| OK | |
| 6.CHECK WIRE HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE - EFI MAIN1 RELAY) |
Disconnect the ECM connector.
Remove the EFI MAIN1 relay from the engine room relay block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| EFI MAIN1 relay terminal 3 - C7-1 | Always | Below 1 Ω |
| EFI MAIN1 relay terminal 3 - C24-1 | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| EFI MAIN1 relay terminal 3 or C7-1 - Body ground | Always | 10 kΩ or higher |
| EFI MAIN1 relay terminal 3 or C24-1 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||