DTC P0230 Fuel Pump Primary Circuit |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0230 | Open or short in fuel pump circuit for 2.5 seconds or more. (1 trip detection logic) |
|

| GTS Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| 1.INSPECT TERMINAL VOLTAGE (+B OF FUEL PUMP CONTROL ECU ASSEMBLY) |
![]() |
Disconnect the fuel pump control ECU assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| G12-1 (+B) - Body ground | Ignition switch ON | 11 to 14 V |
| *a | Front view of wire harness connector (to Fuel Pump Control ECU Assembly) |
|
| ||||
| OK | |
| 2.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU ASSEMBLY - BODY GROUND) |
Disconnect the fuel pump control ECU assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| G12-4 (E) - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (ECM - FUEL PUMP CONTROL ECU ASSEMBLY) |
Disconnect the ECM connector.
Disconnect the fuel pump control ECU assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A35-10 (DI) - G12-3 (DI) | Always | Below 1 Ω |
| A35-19 (FPC) - G12-2 (FPC) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| A35-10 (DI) or G12-3 (DI) - Body ground | Always | 10 kΩ or higher |
| A35-19 (FPC) or G12-2 (FPC) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 4.INSPECT FUEL PUMP ASSEMBLY |
Inspect the fuel pump assembly (Click here).
|
| ||||
| OK | |
| 5.REPLACE FUEL PUMP CONTROL ECU ASSEMBLY |
Replace the fuel pump control ECU assembly (Click here).
| NEXT | |
| 6.CONFIRM WHETHER DTC OUTPUT RECURS |
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs (Click here).
Crank the engine for 15 seconds.
Idle the engine for 1 minute.
Enter the following menus: Powertrain / Engine / DTC.
Read the DTCs.
| Result | Proceed to |
| No DTC output | A |
| DTC P0230 output | B |
|
| ||||
| A | ||
| ||
| 7.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU ASSEMBLY - FUEL PUMP ASSEMBLY) |
Disconnect the fuel pump control ECU assembly connector.
Disconnect the fuel pump assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| G12-5 (FP-) - G7-4 (FP-) | Always | Below 1 Ω |
| G12-6 (FP+) - G7-3 (FP+) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| G12-5 (FP-) or G7-4 (FP-) - Body ground | Always | 10 kΩ or higher |
| G12-6 (FP+) or G7-3 (FP+) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 8.INSPECT RELAY (C/OPEN) |
Inspect the C/OPEN relay .
|
| ||||
| OK | |
| 9.INSPECT RELAY (C/OPEN RELAY OPERATION) |
Check the relay operation sound when the ignition switch is turned to ON.
| Item | Condition | Standard |
| C/OPEN RELAY | Ignition switch OFF → Ignition switch ON | Operation sound is heard. |
|
| ||||
| OK | |
| 10.CHECK HARNESS AND CONNECTOR (C/OPEN RELAY - FUEL PUMP CONTROL ECU ASSEMBLY) |
Remove the C/OPEN relay from the engine room relay block assembly.
Disconnect the fuel pump control ECU assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| C/OPEN relay terminal 3 - G12-1 | Always | Below 1 Ω |
| C/OPEN relay terminal 1 - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| C/OPEN relay terminal 3 or G12-1 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||