DTC C1273 Low Output Signal of Rear Speed Sensor RH (Test Mode DTC) |
DTC C1274 Low Output Signal of Rear Speed Sensor LH (Test Mode DTC) |
DTC C1332 Open in Rear Speed Sensor RH |
DTC C1333 Open in Rear Speed Sensor LH |
DTC C1466 Rear Speed Sensor RH |
DTC C1467 Rear Speed Sensor LH |

| DTC No. | DTC Detection Condition | Trouble Area |
| C1332 C1333 | An open or short in the speed sensor signal circuit. |
|
| C1466 C1467 | An abnormal signal is received from a wheel speed sensor. |
|
| C1273 C1274 | Detected only during Test Mode. |
|

| 1.READ VALUE USING GTS (REAR SPEED SENSOR) |
Connect the GTS to the DLC3.
Start the engine.
Select the Data List using the GTS (Click here).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| RR Wheel Speed | Rear wheel speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326.4 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| RL Wheel Speed | Rear wheel speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326.4 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
Check the speed value output from the speed sensor displayed on the GTS.
|
| ||||
| OK | |
| 2.PERFORM TEST MODE INSPECTION (SIGNAL CHECK) |
Turn the ignition switch off.
Perform the sensor check using the Test Mode procedure (Click here).
|
| ||||
| OK | |
| 3.RECONFIRM DTC |
Clear the DTCs (Click here).
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 45 km/h (28 mph) or more for at least 120 seconds.
Check if the same DTC is output (Click here).
| Result | Proceed to |
| DTCs C1332, C1333, C1466 and C1467 are not output. | A |
| DTCs C1332, C1333, C1466 and/or C1467 are output. | B |
|
| ||||
| A | ||
| ||
| 4.CHECK REAR SPEED SENSOR INSTALLATION |
![]() |
Turn the ignition switch off.
Check the speed sensor installation.
|
| ||||
| OK | |
| 5.CHECK REAR SPEED SENSOR TIP |
Remove the rear speed sensor (Click here).
Check the speed sensor tip.
|
| ||||
| OK | |
| 6.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - REAR SPEED SENSOR) |
Install the rear speed sensor (Click here).
Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the skid control ECU (brake actuator assembly) connector and the rear speed sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A5-17 (RR+) - G9-2 (RR+) | Always | Below 1 Ω |
| A5-17 (RR+) - Body ground | Always | 10 kΩ or higher |
| A5-29 (RR-) - G9-1 (RR-) | Always | Below 1 Ω |
| A5-29 (RR-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| A5-31 (RL+) - H12-2 (RL+) | Always | Below 1 Ω |
| A5-31 (RL+) - Body ground | Always | 10 kΩ or higher |
| A5-18 (RL-) - H12-1 (RL-) | Always | Below 1 Ω |
| A5-18 (RL-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 7.INSPECT BRAKE ACTUATOR ASSEMBLY (REAR SPEED SENSOR POWER SOURCE TERMINAL) |
Reconnect the skid control ECU (brake actuator assembly) connector.
![]() |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| G9-2 (RR+) - Body ground | Ignition switch ON | 8 to 14 V |
| Tester Connection | Condition | Specified Condition |
| H12-2 (RL+) - Body ground | Ignition switch ON | 8 to 14 V |
| *A | for RH |
| *B | for LH |
| *a | Front view of wire harness connector (to Rear Speed Sensor) |
|
| ||||
| OK | |
| 8.RECONFIRM DTC |
Reconnect the rear speed sensor connector.
Clear the DTCs (Click here).
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 45 km/h (28 mph) or more for at least 120 seconds.
Check if the same DTC is output (Click here).
| Result | Proceed to |
| DTCs C1332, C1333, C1466 and/or C1467 are output. | A |
| DTCs C1332, C1333, C1466 and C1467 are not output. | B |
|
| ||||
| A | |
| 9.REPLACE REAR SPEED SENSOR |
Turn the ignition switch off.
Replace the rear speed sensor (Click here).
| NEXT | |
| 10.RECONFIRM DTC |
Clear the DTCs (Click here).
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 45 km/h (28 mph) or more for at least 120 seconds.
Check if the same DTC is output (Click here).
| Result | Proceed to |
| DTCs C1332, C1333, C1466 and/or C1467 are output. | A |
| DTCs C1332, C1333, C1466 and C1467 are not output. | B |
|
| ||||
| A | |
| 11.REPLACE REAR SPEED SENSOR ROTOR |
Turn the ignition switch off.
Replace the rear speed sensor rotor (Click here).
| NEXT | |
| 12.RECONFIRM DTC |
Clear the DTCs (Click here).
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 45 km/h (28 mph) or more for at least 120 seconds.
Check if the same DTC is output (Click here).
| Result | Proceed to |
| DTCs C1332, C1333, C1466 and/or C1467 are output. | A |
| DTCs C1332, C1333, C1466 and C1467 are not output. | B |
|
| ||||
| A | ||
| ||