Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM

DTC    C1249    Open in Stop Light Switch Circuit

for Preparation Click here


DESCRIPTION

The skid control ECU (brake actuator assembly) receives stop light switch signals and uses them to determine whether or not the brakes are applied.
DTCs may be stored if one of the following occurs:
  1. Stop light switch stuck on/off malfunction.
  2. Accelerator pedal and brake pedal depressed simultaneously.*

HINT:
*: The skid control ECU (brake actuator assembly) may store this DTC upon judging that a stuck on malfunction has occurred when the accelerator pedal and brake pedal are depressed simultaneously. However, this does not indicate a malfunction.


DTC No.
DTC Detection Condition
Trouble Area
C1249
Any of the following is detected:
  1. The vehicle speed is 10 km/h (6 mph) or more, the accelerator pedal is depressed, and the stop light switch is on for 60 seconds or more.
  2. When the stop light switch is off, the master cylinder pressure is increased.
  1. STOP fuse
  2. Stop light switch assembly
  3. Noise filter
  4. Stop light switch circuit
  5. Skid control ECU (Brake actuator assembly)

WIRING DIAGRAM


C261862E01


INSPECTION PROCEDURE

NOTICE:
  1. When replacing the skid control ECU (brake actuator assembly), perform VSC sensor neutral memorization (Click here).
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.
  3. The skid control ECU (brake actuator assembly) may store this DTC upon judging that a stuck on malfunction has occurred when the accelerator pedal and brake pedal are depressed simultaneously.
  4. If the pedals were depressed simultaneously, clear the DTC because it is not a malfunction.

1.READ VALUE USING GTS (STOP LIGHT SW)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Select the Data List using the GTS (Click here).

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Stop Light SW
    Stop light switch / ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    -

  1. Check that the "Stop Light SW" display observed on the GTS changes according to the brake pedal operation.

    OK:
    The GTS displays "ON" or "OFF" according to the brake pedal operation.



NG
Go to step 4
OK


2.READ VALUE USING GTS (MASTER CYLINDER PRESSURE SENSOR 1, STOP LIGHT SW)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Select the Data List using the GTS (Click here).

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Master Cylinder Pressure Sensor 1
    Master cylinder pressure sensor / Min.: -1.00 MPa, Max.: 23.99 MPa
    Brake pedal released: -1 to 0 MPa
    During brake pedal operation: Proportional to pedal pressure
    Stop Light SW
    Stop light switch / ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    -

  1. Check that the "Stop Light SW" and "Master Cylinder Pressure Sensor 1" displays observed on the GTS change according to the brake pedal operation.

    OK:
    When the "Stop Light SW" is turned "ON", the "Master Cylinder Pressure Sensor 1" is within the standard value (0.08 to 0.27 MPa(0.81 to 2.75 kgf/cm2, 11 to 39 psi)).



NG
ADJUST STOP LIGHT SWITCH ASSEMBLY (Click here)
OK


3.RECONFIRM DTC
  1. Turn the ignition switch off.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Start the engine.

  1. Drive the vehicle and depress the brake pedal several times to test the stop light circuit.

  1. Check if the same DTC is output (Click here).

    Result:

    Result
    Proceed to
    DTC C1249 is output.
    A
    DTC C1249 is not output.
    B

    HINT:
    If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts (Click here).



B
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A

REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)  

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)


    C281994E01
  1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

  1. Disconnect the noise filter connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A13-3 - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Noise Filter)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)
OK


5.INSPECT NOISE FILTER
  1. Remove the noise filter (Click here).

  1. Inspect the noise filter (Click here).



NG
REPLACE NOISE FILTER (Click here)
OK


6.CHECK HARNESS AND CONNECTOR (NOISE FILTER - STOP LIGHT SWITCH ASSEMBLY)
  1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

  1. Disconnect the stop light switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    A13-2 - A22-1
    Always
    Below 1 Ω
    A13-1 - A22-2
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    A13-2 or A22-1 - Body ground
    Always
    10 kΩ or higher
    A13-1 or A22-2 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.INSPECT STOP LIGHT SWITCH ASSEMBLY
  1. Remove the stop light switch assembly (Click here).

  1. Inspect the stop light switch assembly (Click here).



NG
REPLACE STOP LIGHT SWITCH ASSEMBLY (Click here)
OK


8.CHECK HARNESS AND CONNECTOR (STP TERMINAL)


    C261861E01
  1. Reconnect the stop light switch assembly connector.

  1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

  1. Disconnect the skid control ECU (brake actuator assembly) connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A5-30 (STP) - Body ground
    Stop light switch ON (Brake pedal depressed)
    11 to 14 V*
    Stop light switch OFF (Brake pedal released)
    Below 1.5 V

    HINT:
    *: The standard voltage value varies depending on the +BS terminal voltage value. The standard voltage is 85% of the +BS terminal voltage.

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU (Brake Actuator Assembly))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)
OK

REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)