Home › Engine / Hybrid System › FA20 ENGINE CONTROL › SFI SYSTEM

DTC    P0451    Evaporative Emission Control System Pressure Sensor Range / Performance

DTC    P0452    Evaporative Emission Control System Pressure Sensor / Switch Low Input

DTC    P0453    Evaporative Emission Control System Pressure Sensor / Switch High Input

for Preparation Click here


DTC SUMMARY


DTC No.
Monitoring Item
Malfunction Detection Condition
Trouble Area
Detection Timing
Detection Logic
P0451
Difference between canister pressure sensor output value and manifold absolute pressure sensor output value
The difference between the canister pressure sensor output value and the manifold absolute pressure sensor output value with the ignition switch ON is large.
  1. Canister pump module
  2. Connector/wire harness
    (Canister pump module - ECM)
  3. EVAP system hose (pipe from air inlet port to canister pump module, canister filter, fuel tank vent hose)
  4. ECM
Ignition switch off to ON
2 trip
P0452
Canister pressure sensor low input
EVAP pressure sensor less than 0.973 V for 1 second.
  1. Ignition switch ON
  2. EVAP monitoring (ignition switch off)
1 trip
P0453
Canister pressure sensor high input
EVAP pressure sensor more than 4.095 V for 1 second.
  1. Ignition switch ON
  2. EVAP monitoring (ignition switch off)
1 trip

HINT:
The canister pressure sensor is built into the canister pump module.


DESCRIPTION

The description can be found in EVAP (Evaporative Emission) System (Click here).

MONITOR DESCRIPTION


A282306E05

  1. DTC P0451: Difference between canister pressure sensor output value and manifold absolute pressure sensor output value
    If the difference between the atmospheric pressure calculated using the canister pressure sensor and that calculated using the MAP sensor exceeds the specified value, then the ECM determines there is a canister pressure sensor abnormality. The ECM then illuminates the MIL and stores the DTC (2 trip detection logic).
  2. DTC P0452: Canister pressure sensor voltage low
    If the canister pressure sensor voltage output (pressure) is below 0.973 V: 51.71 kPa(abs) [388 mmHg(abs)], the ECM interprets this as an open or short circuit in the canister pressure sensor or its circuit, and stops the EVAP system monitor. The ECM then illuminates the MIL and stores the DTC (1 trip detection logic).
  3. DTC P0453: Canister pressure sensor voltage high
    If the canister pressure sensor voltage output (pressure) is 4.095 V: 108.99 kPa(abs) [818 mmHg(abs)] or more, the ECM interprets this as an open or short circuit in the canister pressure sensor or its circuit, and stops the EVAP system monitor. The ECM then illuminates the MIL and stores the DTC (1 trip detection logic).

CONFIRMATION DRIVING PATTERN

  1. Connect the GTS to the DLC3.
  2. Turn the ignition switch to ON and turn the GTS on.
  3. Enter the following menus: Powertrain / Engine / Data List / Intake Air.
  4. Check that the intake air temperature is between 4.4 and 35°C (40 and 95°F).
  5. Clear DTCs (even if no DTCs are stored, perform the clear DTC procedure) (Click here).
  6. Turn the ignition switch off and wait for at least 30 seconds.
  7. Turn the ignition switch to ON and turn the GTS on.
  8. Enter the following menus: Powertrain / Engine / Utility / All readiness.
  9. Input the DTC: P0451, P0452 or P0453.
  10. Check the DTC judgment result.

    GTS Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.

  11. If the judgment result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM


A282407E03


INSPECTION PROCEDURE

NOTICE:
  1. When a vehicle is brought into the workshop, leave it as it is. Do not change the vehicle condition. For example, do not tighten the fuel cap.
  2. Do not disassemble the canister pump module.
  3. The GTS is required to conduct the following diagnostic troubleshooting procedure.
  4. Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CONFIRM DTC AND EVAP PRESSURE
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON (do not start the engine).

  1. Turn the GTS on.

  1. Enter the following menus: Powertrain / Engine / Trouble Codes.

  1. Read DTCs.

  1. Enter the following menus: Powertrain / Engine / Data List / Vapor Pressure Pump.

  1. Read the EVAP (Evaporative Emission) pressure displayed on the GTS.

    Result 
    Display (DTC Output)
    Test Result
    Suspected Trouble Area
    Proceed to
    P0451
    -
    1. Canister pressure sensor
    2. Manifold absolute pressure sensor
    C
    P0452
    Below 51.71 kPa(abs) [388 mmHg(abs)]
    1. Wire harness/connector (ECM - Canister pressure sensor)
    2. Canister pressure sensor
    3. Short in ECM circuit
    A
    P0453
    Higher than 108.99 kPa(abs) [818 mmHg(abs)]
    1. Wire harness/connector (ECM - Canister pressure sensor)
    2. Canister pressure sensor
    3. Open in ECM circuit
    B



B
Go to step 4

C
Go to step 8
A


2.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM)
  1. Turn the ignition switch off.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Result 
    Tester Connection
    Condition
    Specified Condition
    Suspected Trouble Area
    Proceed to
    A35-20 (PPMP) - Body ground
    Always
    Below 10 Ω
    1. Wire harness/connector (ECM - Canister pressure sensor)
    2. Short in canister pressure sensor circuit
    A
    10 kΩ or higher
    1. Wire harness/connector (ECM - Canister pressure sensor)
    2. Short in ECM circuit
    B



B
Go to step 8
A


3.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM)
  1. Disconnect the canister pump module connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Result 
    Tester Connection
    Condition
    Specified Condition
    Suspected Trouble Area
    Proceed to
    A35-20 (PPMP) - Body ground
    Always
    10 kΩ or higher
    Short in canister pressure sensor circuit
    A
    Below 10 Ω
    Short in wire harness/connector (ECM - Canister pressure sensor)
    B



A
Go to step 6

B
Go to step 7

4.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM)


    A281930E01
  1. Disconnect the canister pump module connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G8-8 - Body ground
    Always
    100 Ω or less

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Canister Pump Module)

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    G8-6 - Body ground
    Ignition switch ON
    4.5 to 5.5 V
    G8-7 - Body ground
    Ignition switch ON
    4.5 to 5.5 V


    Result 
    Test Result
    Suspected Trouble Area
    Proceed to
    Voltage and resistance within standard ranges
    Open in canister pressure sensor circuit
    A
    Voltage and/or resistance outside standard ranges
    Open in wire harness/connector (ECM - Canister pressure sensor)
    B



B
Go to step 7
A


Go to step 6

5.REPLACE CANISTER PUMP MODULE
  1. Replace the canister pump module (Click here).



NEXT
Go to step 12

6.REPAIR OR REPLACE HARNESS OR CONNECTOR (CANISTER PUMP MODULE - ECM)


NEXT
Go to step 12

7.REPLACE ECM
  1. Replace the ECM (Click here).



NEXT
Go to step 12

8.READ VALUE USING GTS (ATMOSPHERE PRESSURE)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Powertrain / Engine / Data List / Atmosphere Pressure.

  1. Compares Atmosphere Pressure displayed with the GTS to the actual atmosphere pressure.


Result 
Result
Proceed to
Difference with the actual atmosphere pressure is less than 4.7 kPa (abs) [36 mmHg (abs)].
A
Difference with the actual atmosphere pressure is 4.7 kPa (abs) [36 mmHg (abs)] or more.
B


B
Go to step 10
A


9.READ VALUE USING GTS (MAP)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Powertrain / Engine / Data List / MAP.

  1. Compares the MAP displayed with the GTS to the actual atmosphere pressure.


Result 
Result
Proceed to
Difference with the actual atmosphere pressure is less than 4.7 kPa (abs) [36 mmHg (abs)].
A
Difference with the actual atmosphere pressure is 4.7 kPa (abs) [36 mmHg (abs)] or more.
B


B
Go to step 11
A

CHECK INTERMITTENT PROBLEMS (Click here)  

10.REPLACE CANISTER PUMP MODULE
  1. Replace the canister pump module (Click here).



NEXT
Go to step 12

11.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
  1. Replace the manifold absolute pressure sensor (Click here).



NEXT
Go to step 12

12.CHECK WHETHER DTC OUTPUT RECURS (AFTER REPAIR)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off and wait for at least 60 seconds.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Perform the Evaporative System Check using the GTS, referring to the Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine / Utility / All Readiness.

  1. Input the DTC: P0451, P0452 or P0453.

  1. Check the DTC judgment result.

    Result 
    GTS Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit


NEXT

END